Инструкция для EXTRON ELECTRONICS IN1608 MA User Guide, IN1608 SA User Guide, IN1606 User Guide, IN1608 Series User Guide

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

 

IN1606 and IN1608 Series Scaling Presentation Switcher • Installation

9

Power and Input Connections

Output and Control Connections

a

 AC power connector

b

 Analog video connectors — inputs 1 and 2

c

 HDMI connectors — inputs 3 and higher

d

 DTP input and corresponding RS-232/IR  

    

 

Over DTP connectors — inputs 7 and 8

e

 Analog audio input connectors  

— inputs 1 to 6

f

 Mic/Line connectors — inputs 1 and 2

g

 DTP output and corresponding  

   

  

RS-232/IR Over DTP connector —  

   

  

output C

h

 HDMI connectors — outputs A and B

i

 Analog audio output connectors

j

 Amplified audio output connectors

k

 LAN connector

l

 RS-232 connector

a

 

Power connector — Connect the standard IEC power cord from a 100 to 240 VAC, 
50-60 Hz power source into this connector. The front panel control and input selection 
buttons light in sequence during power-up. 

b

 

Analog video connectors — Connect video sources to the 15-pin HD connectors. 
Each accepts RGB, YUV, RGBcvS, S-video, and composite video (see 

Analog Video 

Wiring

 on page 12).

c

 

HDMI input connectors — Connect video sources to the HDMI connectors.

TIP:  Use Extron HDMI LockIt Lacing Brackets to secure HDMI cables to the device 

(see 

HDMI Connections

 on page 12).

d

   DTP input connectors (IN1608 models only) — Connect a DTP 230 transmitter to 

either DTP In RJ-45 connector to send all signals over a single twisted pair cable (see 

Twisted Pair Recommendations for DTP Communication

 on page 13 for wiring 

and cable recommendations). This connection supports the following:

• 

HDCP-compliant digital video

• 

Embedded digital audio de-embedding from the TMDS source or analog audio

• 

DTP standard RS-232 and IR pass-through signals on associated 5-pole captive 
screw connectors.

• 

Remote power to DTP 230 transmitters

ATTENTION: 

• 

Do not connect this connector to a computer or telecommunications network.

• 

DTP remote power is intended for indoor use only. No part of the network that 
uses DTP remote power should be routed outdoors.

Signal LED — Lights when the scaler is receiving an active video signal from a DTP 
transmitter.
Link LED — Lights when a valid link is established to a DTP transmitter.
RS-232 Over DTP port — To pass bidirectional serial control between  
DTP-compatible devices, connect a control device to the 5-pole captive 
screw connector. This port includes only the 3 poles labeled “RS-232.”
IR Over DTP port — To transmit and receive IR signals, connect a control 
device to the 5-pole captive screw connector. This port includes only the  
2 poles labeled “IR” and shares the ground pole with the RS-232 port.

NOTE:  RS-232 and IR data can be transmitted simultaneously.

IR

Tx Rx G

Tx Rx

RS-232

IR

Tx Rx G

Tx Rx

RS-232

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
Оглавление инструкции

Document Outline