Инструкция для EXTRON ELECTRONICS IN1608 MA User Guide, IN1608 SA User Guide, IN1606 User Guide, IN1608 Series User Guide

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

 

IN1606 and IN1608 Series Scaling Presentation Switcher • Operation

30

Reset Modes

There are three reset modes (numbered 1, 4, and 5). These are available by pressing the 
recessed Reset button on the rear panel (see the following table for a summary of the reset 
modes).

ATTENTION:  Review the reset modes carefully. Using the wrong reset mode may result 

in unintended loss of flash memory programming, port reassignment, or processor 
reboot.

NOTE:  The reset modes listed close all open IP and Telnet connections and all sockets. 

Each mode is a separate function, not a continuation from mode 1 to mode 5.

Reset Mode Summary

Mode

Activation

Result

Purpose/Notes

 Use Factory Firmwar

e

1

Hold in the recessed Reset button for 
30 seconds while applying power to the 
scaler.

NOTE:  After a mode 1 reset, 

update the device with the latest 
firmware version. 

DO NOT 

operate with the firmware version 
that results from this mode reset. 
This temporarily resets the device 
to factory default until power is 
recycled. To use factory default 
firmware, upload that version 
again.

The device reverts to the factory default 
firmware.

• 

Firmware reverts to the factory default for a 
single power cycle.

• 

All user files and settings (drivers, audio 
and video adjustments, IP settings, and so 
on) are maintained.

NOTE:  If you do not want to update the 

firmware or perform a mode 1 reset by 
mistake, cycle power to the device to 
return to the firmware version running 
prior to the reset. 

Use mode 1 to revert 
to the factory default 
version if incompatibility 
issues arise with  
user-loaded firmware.

Reset IP 

 

Settings

4

Hold down the Reset button for 
approximately 6 seconds until the Reset 
LED blinks twice. Then press Reset 
momentarily (<1 second).

IP settings revert to factory defaults.

• 

Port mapping reverts to factory default.

• 

DHCP turns off.

• 

IP address is set to 192.168.254.254.

• 

Reset LED blinks four times in quick 
succession during reset.

Use mode 4 to reset 
all IP settings back to 
factory defaults.

Reset to Factory Default

5

Hold down the Reset button for 
approximately 9 seconds until the Power 
LED blinks 3 times. Then press Reset 
momentarily (<1 second).

The device reverts to the factory defaults 
except for firmware.

• 

Mode 4 results are performed.

• 

All user modifiable configurations reset to 
default values including IP settings and 
real-time adjustments.

• 

All user loaded files are deleted.

• 

The Reset LED blinks 4 times in quick 
succession during the reset.

Use mode 5 to 
restart with default 
configuration. This 
is equivalent to SIS 
command ZQQQ.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
Оглавление инструкции

Document Outline