Инструкция для EXTRON ELECTRONICS IN1608 MA User Guide, IN1608 SA User Guide, IN1606 User Guide, IN1608 Series User Guide

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

 

IN1606 and IN1608 Series Scaling Presentation Switcher • SIS Configuration and Control

52

Command

ASCII Command 

(host to scaler)

Response 

(scaler to host)

Additional Description

IP Control Port Commands

IP setup

NOTE:     Changes made to any TCP/IP settings do not take effect until the reboot networking command 

(

E

2BOOT

}

) is issued.

Set IP address

24

EX4)

CI

}

Ipi

•X4)]

Set the IP address to 

X4)

.

Read IP address

24

E

CI

}

X4)]

View the current IP address.

Set DHCP mode

EX(

DH

}

Idh

X(]

Enable or disable DHCP.

View DHCP mode

E

DH

}

X(]

View the DHCP mode setting.

Set subnet mask

24

EX4!

CS

}

Ips

•X4!]

Set the subnet mask to 

X4!

.

View subnet mask

E

CS

}

X4!]

View the subnet mask setting.

Set gateway IP address

24

EX4@

CG

}

Ipg

•X4@]

Set the gateway IP address to 

X4@

.

View gateway IP address

E

CG

}

X4@]

View the gateway IP address setting.

Read MAC address

E

CH

}

X4#] 

Iph

•X4#]

00-05-A6-xx-xx-xx

Verbose mode 2 and 3.

Query the number of open 
connections

E

CC

}

X4$] 
 

Icc

X4$]

View the number of open 
connections.
Verbose mode 2 and 3.

Reboot networking

E

2BOOT

}

Boot2

]

Restart the network after IP setting or 
DHCP changes.

NOTE:  Changes to IP or DHCP settings will not take effect until the 

E

2BOOT

}

 command is executed.

NOTES:  

X(

 = Enable or disable                                             

0

 = off or disabled 

                                                                               

 1

 = on or enabled 

X4)

 = IP address                                                   

   

xxx.xxx.xxx.xxx

 (

192.168.254.254

 = default) 

X4!

 = Subnet mask                                               

   

xxx.xxx.xxx.xxx

 (

255.255.0.0

 = default) 

X4@

 = Gateway address                                          

 

xxx.xxx.xxx.xxx

 (

0.0.0.0

 = default) 

X4#

 = MAC address                                                

00-05-A6-xx-xx-xx

 

X4$

 = Number of open connections                      

   

0-<maximum number of open connections>

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
Оглавление инструкции

Document Outline