Инструкция для EXTRON ELECTRONICS IN1608 MA User Guide, IN1608 SA User Guide, IN1606 User Guide, IN1608 Series User Guide

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

 

IN1606 and IN1608 Series Scaling Presentation Switcher • Internal Web Pages

74

Audio Config Page

From the Audio Config page, audio inputs and outputs can be configured and mixed. Click 
the 

Audio Config

 icon on the Global Navigation Bar to open this page. There are four tabs 

for adjusting program and microphone inputs, mixing inputs, and configuring outputs.
Configuring the audio in order of the tabs from left to right will help ensure proper setup of 
input and output levels as well as mix and listening levels.

Configuration overview

Figure 44. 

Audio Configuration Tabs

1. 

From the 

Line Input

 tab, set audio input formats and set the input gain at optimal 

settings.

a. 

Set the audio format of each input (see 

Audio format

 on page 75).

b. 

Set the input gain for analog inputs (see 

Analog input gain

 on page 76).

2. 

From the 

Mic/Line Input

 tab, set the mic gain at optimal settings.

a. 

If necessary, apply phantom power to the applicable microphone inputs (see 

Phantom power

 on page 77).

b. 

Set the microphone input gain (see 

Mic/line gain

 on page 78).

c. 

If desired, apply a high pass filter to the microphone inputs (see 

High pass filter

 on 

page 78).

d. 

If desired, enable ducking for the microphone inputs (see 

Ducking parameters

 on 

page 79).

3. 

After the line input gain and mic gain are properly set, mix the audio levels and set tone 
levels from the 

Mix Controls

 tab. If the results from this step are satisfactory, skip 

steps 4 and 5 as no other settings need to be adjusted.

a. 

Set the mic mix levels (see 

Mic mix levels

 on page 80).

b. 

Set the listening volume of the microphone inputs (see 

Mic volume

 on page 81).

c. 

Set the listening volume of the program audio (see 

Program volume

 on page 81).

d. 

Set the bass and treble levels for the prorgram material (see 

Bass and treble

 on 

page 82).

4. 

If necessary, set output limiters, mix options, or volume from the 

Output

 tab.

a. 

If desired, apply an output limiter to the desired outputs (see 

Limiters

 on page 84).

b. 

Set mix options of the output (see 

Mix options

 on page 84).

c. 

Set the output volume (see 

Output gain

 on page 86).

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
Оглавление инструкции

Document Outline