Инструкция для EXTRON ELECTRONICS PoleVault Digital Switcher Systems PVS 405D

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

A1. Install the PMK 560 Base Plate.

a.  Remove the four cover screws from the center 

of the PMK 560 and slide the two halves apart. 
Remove them from the base plate. 

NOTE: If the PoleVault switcher and its power 

supply are already installed, go directly to 
step 1d.

b.  To mount the PoleVault switcher, place the 

mounting plate, with the raised tabs upwards, 
on the top surface of the switcher and pass the 
two supplied 4-40 x 3/16 inch screws into the 
top of the switcher (see figure at right). Secure 
the mounting plate but do not overtighten. 
Use only the supplied screws to avoid 
damaging the switcher. 

c.  Attach the associated power supply to the base 

plate with the supplied tie wraps by passing 
them through the appropriate slots and around 
the power supply. Tighten until snug

d.  Loosen the four pipe collar set screws and slide 

the base plate up the pipe until it is touching the 
suspended ceiling.

e.  Level the base plate and secure it by fully 

tightening the set screws.

NOTE:

  At least three set screws must come in contact with the pipe.

Å

 Attach the mounting plate to the switcher, 

û 

fasten the power supply to the base plate, 

ü

 secure 

the base plate to the projector pole, 

°

 and hook 

mounting plate tabs into the base plate.

A. PoleVault System (PMK 560 Pole Mount Kit)

• 

Where it goes: Attaches to slotted pipe, above the projector and close to the drop ceiling.

• 

What it does: Supports and hides the installed PVS 405D switcher and power supply from view.

PMK Covers (2)

Base Plate

To open, remove 4 cover screws 
and slide the covers away.

Mounting Plate

L

R

DO 

NOT

GR

OUND

OR

 SH

ORT

SPE

AKER

OUTPUTS

4/8

Ω

3A M

AX

POW

ER

12V

HDMI

1/2

SIG

LINK

SIG

LINK

3/4

INPU

TS

OUTPU

T

AUD

IO 

OUT

PVS 405S

A IP

AMPL

IFIED AUDIO 

OUT

PAGI

NG

SENS

OR

PVT I

N

PVT 

IN

L

R

AUX

OVE

R PVT

REMOTE

VOI

CE

LIFT

LAN 1

LAN 2

LA

N 3

INPUT

 5

+V

L

R

RS

-232

Tx Rx

IR

S

G

G

Attach the mounting plate
to the top of the
PoleVault switcher.

1b

Hook the combined mounting 
plate and switcher into the 
base plate and secure with 
screws.

Projector

Pole

Attach

Power 

Supply

Attach PMK to the projector 
pole. Secure the pipe collar 
with the four
10-32 set screws.

PVS 405D

Switcher

1c

1d

1f

1e

 

PoleVault Digital Systems • Installation — Stage 4 (PMK 560 and PVS 405D)

40

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Оглавление инструкции

Document Outline