Инструкция для EXTRON ELECTRONICS PoleVault Digital Switcher Systems PVS 405D

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

C1. Install the USFM 100 Base Plate.

NOTES:

 

• 

It is required to attach the base plate to two wall studs, using a minimum of four securing points

• 

 Drywall KapToggles can be used for holes not aligned with studs.

• 

 Always use the widest spacing of screws and KapToggles.

• 

The base plate can be installed over an existing electrical outlet.

 

a.  Grasp handle, collapse
     toggle and insert into wall.

b.  Slide plastic washer
     down into pilot hole.

c.  Cut off handle close to wall. d.  Hand screw in pan head

     bolt until 1/8" gap remains.

Toggle Assembly Installation

Cutout for
Signal Cable
Access

Marker for 
Pilot Hole

Mounting
Holes

Signal Cables
Exiting from
Cutout

Cut out a Cable Access Area

a.  To mount the USFM 100 onto non-masonry 

walls, at the desired site, use an edge-to-
edge stud finder to locate the center of the wall 
studs (wood or steel). Mark each stud location. 
Minimum joist size should be 2 by 4 inches.

b.  Hold and level the base plate against the wall. 

Mark a minimum of four positions (two top, two 
bottom) using either the mounting slots or the 
keyholes (slots uppermost) that are on the stud 
lines. Where applicable, mark the mounting 
holes on the wall for drywall toggles. 

c.  If the cables are to be run behind the wall to the 

USFM 100 location, mark the cutout area on 
the wall large enough for signal cables. 

d.  Remove the base plate and set it aside. Cut out 

the marked area for cable access.

For drywall with wood studs

i. 

Drill ¼ inch diameter pilot holes at the marked 
stud locations.

ii. 

Align the base plate mounting holes over the 
pilot holes and lightly secure with 5/16 inch lag 
screws and washers.

iii. 

Verify level and position, and fully tighten down 
all the screws to secure the plate.

For drywall with steel studs

i. 

Drill a ½ inch (13 mm) hole through the stud at 
each of the locations (four recommended). 

ii. 

Insert the supplied toggles through the studs 
and lightly secure the plate using the four 
supplied (¼-20 x 2 inch) bolts and washers.

iii. 

Verify level and position, and fully tighten down 
all the bolts to secure the plate flush to the wall.

C2. Install the Switcher Onto the Base Plate.

a.  Place the mounting plate flat on the switcher 

base with the two small raised tabs on top, and 
the small securing tab over the front panel. Align 
the two mounting holes in the switcher base 
with the corresponding holes on the mounting 
plate. Secure the plate to the switcher using the 
two 4-40 x ¼ inch pan head screws.  

 

PoleVault Digital Systems • Installation — Stage 4 (USFM 100 and PVS 405D)

48

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
Оглавление инструкции

Document Outline