Инструкция для GIGABYTE GA-8IE2004, GA-8IE2004-L

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

When you installing AGP card, please make sure the following
notice is fully understood and practiced. If your AGP card has "AGP
4X notch"(show below), please make sure your AGP card is AGP 4X
(1.5V).

Caution: AGP 2X card is not supported by Intel

®

 845(GE/PE) / 845(E/

G) / 850(E) / E7205 / 865(G/PE/P) / 875P.  You might experience system
unable to boot up normally. Please insert an AGP 4X/8X card.

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X
mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X (1.5V) mode
by adjusting the jumper. The factory default for this card is 2X (3.3V). If you
install this card in GA-8IE2004 Series (or any AGP 4X/8X only) motherboards
without switching the jumper to 4X mode (1.5V), it will burn the motherboard.

Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color",
the graphics card manufacturer & some SiS 305 cards, their golden finger is
compatible with 2X/4X mode AGP slot, but they support 2X (3.3V) only. If you
install this card in GA-8IE2004 Series (or any AGP 4X/8X only) motherboards,
it will burn the motherboard.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage
128 Pro chip, the design of AG32S(G) is compliance with AGP 4X (1.5V)
specification. Therefore, AG32S(G) will work fine with Intel

®

 845(GE/PE) / 845

(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P based motherboards.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Оглавление инструкции
  • Страница 1 из 97
    When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1.5V). Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/ G) / 850(E) / E7205 /
  • Страница 2 из 97
    The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Please do not remove any labels on
  • Страница 3 из 97
    Declaration of Conformity We, Manufacturer/Importer (full address) .. G.B.T. Technology Trading GMbH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-8IE2004 / GA-8IE2004-L is in
  • Страница 4 из 97
    DECLARATION OF CONFORMITY Per FCC Part 2 Section 2.1077(a) Responsible Party Name: G.B.T. INC. (U.S.A.) Address: 17358 Railroad Street City of Industry, CA 91748 Phone/FaxNo: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Motherboard ModelNumber: GA-8IE2004 /
  • Страница 5 из 97
    GA-8IE2004 Series P4 Titan Series Motherboard USER'S MANUAL Pentium® 4 Processor Motherboard Rev. 1001 12ME-8IE2004-1001
  • Страница 6 из 97
    English Table of Content Item Checklist ......................................................................................... 4 WARNING! ............................................................................................... 4 Chapter 1 Introduction
  • Страница 7 из 97
    Frequency/Voltage Control ........................................................................ 49 Top Performance ...................................................................................... 51 Load Fail-Safe Defaults
  • Страница 8 из 97
    English Item Checklist The GA-8IE2004 Series motherboard 2 Port USB Cable x 1 CD for motherboard driver & utility 4 Port USB Cable x 1 SPDIF KIT x 1 (SPD-KIT) GA-8IE2004 Series user's manual IEEE 1394 Cable x 1 Audio Combo Kit x 1 Quick PC Installation Guide RAID Manual I/O Shield * (SURROUND-Kit +
  • Страница 9 из 97
    English Chapter 1 Introduction Features Summary Form Factor 20cm x 29.4cm ATX size form factor, 4 layers PCB CPU Socket 478 for Intel® Micro FC-PGA2 Pentium® 4 processor Support Intel® Pentium® 4 (Northwood, 0.13 m) processor Support Intel® Pentium® 4 Processor with HT Technology (Note) Intel®
  • Страница 10 из 97
    English On-Board Sound Realtek ALC655 CODEC Supports Jack-Sensing function Line Out / 2 front speaker Line In / 2 rear speaker(by s/w switch) Mic In / center & subwoofer(by s/w switch) SPDIF In / Out On-Board LAN * CD In / AUX In / Game port Built-in RTL8100C * PS/2 Connector 1 RJ45 port * PS/2
  • Страница 11 из 97
    English GA-8IE2004 Series Motherboard Layout CPU_FAN COMA ATX USB LAN* KB_MS LPT ATX_12V CODEC 2X_DET PCI1 DDR3 AGP DDR1 CD_IN DDR2 GA-8IE2004 Intel 845E GAME MIC_IN LINE_OUT LINE_IN F_AUDIO FDD COMB SOCKET478 BATTERY PCI2 (-L)* SUR_CEN PCI3 RTL* 8100C Hyper Threading CLR_PWD ICH2 SYS _FAN CI PCI4
  • Страница 12 из 97
    Pentium 4 CPU CPUCLK+/- (100/133 MHz) AGP 4X System Bus 400/533 MHz AGPCLK (66MHz) DDR 100/133MHz Intel 845E 5 PCI HCLK+/- (100/133MHz) MCHCLK(66MHz) 66 MHz 33 MHz 14.318 MHz 48 MHz RJ45* RTL8100C* AC97 Link AC97 CODEC BIOS Intel ICH 2 Game Port LPC BUS ITE 8712 48 MHz Floppy LPT Port PS/2 KB/Mouse
  • Страница 13 из 97
    English -9- Introduction
  • Страница 14 из 97
    English GA-8IE2004 Series Motherboard - 10 -
  • Страница 15 из 97
    To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 5- Setup BIOS software Step 6- Install supporting
  • Страница 16 из 97
    English Step 1: Install the Central Processing Unit (CPU) Before installing the processor, adhere to the following warning: 1. Please make sure the CPU type is supported by the motherboard. 2. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause improper installation.
  • Страница 17 из 97
    Before installing the CPU cooling fan, adhere to the following warning: 1. Please use Intel approved cooling fan. 2. We recommend you to apply the thermal tape to provide better heat conduction between your CPU and cooling fan. (The CPU cooling fan might stick to the CPU due to the hardening of the
  • Страница 18 из 97
    English Step 2: Install Memory Modules Before installing the memory modules, adhere to the following warning: 1. When DIMM LED is ON, do not install / remove DIMM from socket. 2. Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause
  • Страница 19 из 97
    Devices used on DIMM 1 DIMM x 64 / x 72 2 DIMMs x 64 / x 72 3 DIMMs x 64 / x 72 64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(4Mx8x4 banks) 128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 256 Mbit(4Mx16x4 banks) 512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks) 128 MBytes 32 MBytes 256
  • Страница 20 из 97
    English Step 3: Install expansion cards 1. Read the related expansion card's instruction document before install the expansion card into the computer. 2. Remove your computer's chassis cover, screws and slot bracket from the computer. 3. Press the expansion card firmly into expansion slot in
  • Страница 21 из 97
    Step 4-1: I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse Connector PS/2 Mouse Connector (6 pin Female) This connector supports standard PS/2 keyboard and PS/2 mouse. PS/2 Keyboard Connector (6 pin Female) LAN* / USB Connector LAN is fast Ethernet with 10/100Mbps speed.* Before you connect
  • Страница 22 из 97
    English Parallel Port and Serial Ports (COMA / COMB) Parallel Port (25 pin Female) This connector supports 2 standard COM ports and 1 Parallel port. Device like printer can be connected to Parallel port; mouse and modem etc. can be connected to Serial ports. COMA COMB Serial Port (9 pin Male) This
  • Страница 23 из 97
    English Step 4-2: Connectors Introduction 3 1 2 10 5 9 12 18 11 17 4 16 6 8 13 14 1) 2) 3) 4) 5) 6) 7) 8) 9) ATX_12V ATX CPU_FAN SYS_FAN FDD IDE1 / IDE2 F_PANEL PWR_LED 2X_DET 15 10) 11) 12) 13) 14) 15) 16) 17) 18) - 19 - 7 F_AUDIO SUR_CEN CD_IN AUX_IN SPDIF_IO F_USB CI CLR_PWD BATTERY Hardware
  • Страница 24 из 97
    English 1) ATX_12V (+12V Power Connector) This connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this "ATX_12V connector" is not connected, system cannot boot. Pin No. 3 1 4 2 Definition 1 2 GND GND 3 4 +12V +12V 2) ATX (ATX Power) AC power cord should only be connected to your
  • Страница 25 из 97
    Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating. The CPU fan connector supports Max. current up to 600 mA. Pin No. Definition 1 2 GND +12V 3 1 Sense 4) SYS_FAN (System Fan Connector) This connector
  • Страница 26 из 97
    English 5) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and 2.88M bytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1. 34 33 2 1 6) IDE1 / IDE2 (IDE1 / IDE2 Connector) Important Notice:
  • Страница 27 из 97
    Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront panel to the F_PANEL connector according to the pin assignment above. Message LED/ Power/ Sleep LED 2 1 1 SPK- SPK+ MPD+ MPDPW+ PW- Soft Power Connector Speaker Connector 20 19 1 1 1 RST+ NC HD+ RST-
  • Страница 28 из 97
    English 8) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color. Pin No. 1 1 2 3 Definition MPD+ MPDMPD- 9) 2X_DET When an AGP 2X (3.3V)
  • Страница 29 из 97
    If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis
  • Страница 30 из 97
    English 12) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. 1 Definition CD-L 2 3 4 1 GND GND CD-R 13) AUX_IN (AUX In Connector) Connect other device (such as PCI TV Tunner audio out) to the connector. Pin No. 1 Definition AUX-L GA-8IE2004 Series Motherboard -
  • Страница 31 из 97
    The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment
  • Страница 32 из 97
    English 16) CI (CASE OPEN) This 2-pin connector allows your system to enable or disable the "Case Open" item in BIOS, if the system case begin remove. Pin No. 1 Definition 1 2 Signal GND 17) CLR_PWD When Jumper is set to "open" and system is restarted, the password that is set will be cleared. On
  • Страница 33 из 97
    + CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. If you want to erase CMOS... 1. Turn OFF the computer and unplug the power cord.
  • Страница 34 из 97
    English GA-8IE2004 Series Motherboard - 30 -
  • Страница 35 из 97
    BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the computer
  • Страница 36 из 97
    English GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the
  • Страница 37 из 97
    English Integrated Peripherals This setup page includes all onboard peripherals. Power Management Setup This setup page includes all the items of Green function features. PnP/PCI Configurations This setup page includes all the configurations of PCI & PnP ISA resources. PC Health Status This setup
  • Страница 38 из 97
    English Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Date (mm:dd:yy) Wed, Jul 16 2003 Time (hh:mm:ss) 22:31:24 Item Help Menu Level Change the day, month, IDE Primary Master [None] IDE Primary Slave [None] year IDE Secondary Master [None]
  • Страница 39 из 97
    time clock. For example, 1 p.m. is 13:00:00. IDE Primary Master, Slave / IDE Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the computer. There are two types: auto type, and manual type. Manual type is user-definable; Auto type
  • Страница 40 из 97
    English Floppy 3 Mode Support (for Japan Area) Disabled Normal Floppy Drive. (Default value) Drive A Drive A is 3 mode Floppy Drive. Drive B Drive B is 3 mode Floppy Drive. Both Drive A & B are 3 mode Floppy Drives. Halt on The category determines whether the computer will stop if an error is
  • Страница 41 из 97
    English Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Advanced BIOS Features First Boot Device [Floppy] Item Help Second Boot Device [HDD-0] Menu Level Third Boot Device [CDROM] Select Boot Device Boot Up Floppy Seek [Disabled] priority Password Check [Setup] CPU
  • Страница 42 из 97
    English USB-CDROM Select your boot device priority by USB-CDROM. USB-HDD Select your boot device priority by USB-HDD. LAN Select your boot device priority by LAN. Disabled Select your boot device priority by Disabled. Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive
  • Страница 43 из 97
    English Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Integrated Peripherals On-Chip Primary PCI IDE [Enabled] Item Help On-Chip Secondary PCI IDE [Enabled] Menu Level IDE1 Conductor Cable [Auto] [Auto] IDE2 Conductor Cable [Auto] Auto-detect IDE USB Controller
  • Страница 44 из 97
    English IDE1 Conductor Cable Auto Will be automatically detected by BIOS. (Default Value) ATA66/100 Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). ATA33 Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is
  • Страница 45 из 97
    Enabled Enable onboard H/W LAN function. (Default Value) Disabled English Onboard H/W LAN* Disable this function. Onboard LAN Boot ROM* This function decide whether to invoke the boot ROM of the onboard LAN chip. Enabled Enable this function. Disabled Disable this function. (Default Value) Onboard
  • Страница 46 из 97
    English Parallel Port Mode SPP Using Parallel port as Standard Parallel Port. (Default Value) EPP Using Parallel port as Enhanced Parallel Port. ECP Using Parallel port as Extended Capabilities Port. ECP+EPP Using Parallel port as ECP & EPP mode. ECP Mode Use DMA 3 Set ECP Mode Use DMA to 3.
  • Страница 47 из 97
    English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type [S1(POS)] Item Help Power LED in S1 state [Blinking] Menu Level Soft-Off by PWR-BTTN [Instant-Off] [S1] PME Event Wake Up [Enabled] Set suspend type to ModemRingOn
  • Страница 48 из 97
    English Soft-off by PWR_BTTN Instant-off Press power button then Power off instantly. (Default value) Delay 4 Sec. Press power button 4 sec to Power off. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up Disabled Disable this function. Enabled Enable PME Event Wake up. (Default
  • Страница 49 из 97
    Enter Input password (from 1 to 5 characters) and press Enter to set the Key board Power On Password. AC Back Function Memory System power on depends on the status before AC lost. Soft-Off Always in Off state when AC back. (Default value) Full-On Always power on the system when AC back. - 45 - BIOS
  • Страница 50 из 97
    English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI 1/5 IRQ Assignment [Auto] Item Help PCI 2 IRQ Assignment [Auto] Menu Level PCI 3 IRQ Assignment [Auto] PCI 4 IRQ Assignment [Auto] Device(s) using this INT: Display Cntrlr -BUS 1 Dev
  • Страница 51 из 97
    English PC Health Status CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PC Health Status Reset Case Open Status [Disabled] Item Help Case Opened No Menu Level Vcore 1.696V [Disabled] VCC18 1.776V Don't reset case +3.3V 3.248V open status +5V 5.134V +12V 12.288V [Enabled] Current CPU
  • Страница 52 из 97
    English Current CPU/SYSTEM FAN Speed (RPM) Detect CPU/System Fan speed status automatically. CPU Warning Temperature Disabled Don't monitor CPU's temperature. (Default value) 60 C/140 F Alarm when CPU current temperature over than 60oC/140oF. 70 o C/158o F Alarm when CPU current temperature over
  • Страница 53 из 97
    English Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Frequency/Voltage Control CPU Clock Ratio [15X] Item Help CPU Host Clock Control [Disabled] Menu Level x CPU Host Frequency (Mhz) 100 x PCI/AGP Fixed 33/66 Host/DRAM Clock ratio [Auto] Memory Frequency (Mhz)
  • Страница 54 из 97
    English Fixed PCI/AGP Fixed You can choose Disabled, 33/66, 38/76, 43/86 mode to adjust PCI/AGP frequency. Host/DRAM Clock Ratio (Warning: wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue) 2.0 2.66 Auto Memory Frequency = Host clock X 2.0. Memory Frequency =
  • Страница 55 из 97
    English Top Performance CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Top Performance Advanced Chipset Features Load Fail-Safe Defaults Integrated Peripherals Top Performance Load Optimized Defaults Power Management Setup Disabled...................[ PnP/PCI
  • Страница 56 из 97
    English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Top Performance Advanced Chipset Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Load Fail-Safe Defaults Supervisor Password
  • Страница 57 из 97
    English Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Top Performance Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password Load Optimized Defaults (Y/N)
  • Страница 58 из 97
    English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Top Performance Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password PnP/PCI Configurations
  • Страница 59 из 97
    English Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Top Performance Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password PnP/PCI Configurations Set User
  • Страница 60 из 97
    English Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Top Performance Advanced BIOS Features Load Fail-Safe Defaults Integrated Peripherals Load Optimized Defaults Power Management Setup Set Supervisor Password PnP/PCI Configurations Set User
  • Страница 61 из 97
    English - 57 - BIOS Setup
  • Страница 62 из 97
    English GA-8IE2004 Series Motherboard - 58 -
  • Страница 63 из 97
    English Chapter 4 Technical Reference @BIOS™ Introduction Gigabyte announces @BIOS™ Windows BIOS live update utility Have you ever updated BIOS by yourself? Or like many other people, you just know what BIOS is, but always hesitate to update it? Because you think updating newest BIOS is unnecessary
  • Страница 64 из 97
    English EasyTune™ 4 Introduction Gigabyte announces EasyTune™ 4 Windows based Overclocking utility EasyTune 4 carries on the heritage so as to pave the way for future generations. Overclock might be one of the most common issues in computer field. But have many users ever tried it? The answer is
  • Страница 65 из 97
    English Flash BIOS Method Introduction Method 1 : Q-Flash A. What is Q-Flash Utility? Q-Flash utility is a pre-O.S. BIOS flash utility enables users to update its BIOS within BIOS mode, no more fooling around any OS. B. How to use Q-Flash? a. After power on the computer, pressing <Del> immediately
  • Страница 66 из 97
    English Update BIOS From Floppy In the A:drive, insert the "BIOS" diskette, then Press Enter to Run. 1 File(s) xxxx.xxx 256K Total size: 1.39M F5: Refresh Free size: 1.14M DEL: Delete Where xxxx.xxx is name of the BIOS file. Press Enter to Run. Are you sure to update BIOS? [Enter] to contiune or
  • Страница 67 из 97
    If you don't have DOS boot disk, we recommend that you used Gigabyte @BIOS™ program to flash BIOS. Press here. 2. Click Start/ All Programs/ GIGABYTE/ @BIOS. 1. Click "@BIOS" item. (1) 3.Click " ". (2) Click here 4. Please select @BIOS sever site, then Click "OK". (3) (4) Methods and steps: I.
  • Страница 68 из 97
    English II. Update BIOS NOT through Internet: a. Do not click "Internet Update" icon b. Click "Update New BIOS" c. Please select "All Files" in dialog box while opening the old file. d. Please search for BIOS unzip file, downloading from internet or any other methods (such as: 8IE2004.E2). e.
  • Страница 69 из 97
    The installation of Windows 98SE/2K/ME/XP is very simple. Please follow next step to install the function! Stereo Speakers Connection and Settings: We recommend that you use the speaker with amplifier to acqiire the best sound effect if the stereo output is applied. STEP 1: Connect the stereo
  • Страница 70 из 97
    English 4 Channel Analog Audio Output Mode STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In". Line Out Line In STEP 2 : After installation of the audio driver, you'll find an icon on the taskbar's status area. Click the audio icon "Sound Effect" from the windows tray
  • Страница 71 из 97
    English Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module. STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In", and the Center/Subwoofer channels to "MIC In". Line Out Line In MIC In STEP 2 :
  • Страница 72 из 97
    English Advanced 6 Channel Analog Audio Output Mode (using Audio Combo Kit, Optional Device): (Audio Combo Kit provides SPDIF output port : optical & coaxis and SURROUND-KIT : Rear R/L & Center/subwoofer) SURROUND-KIT access analog output to rear channels and Center/Subwoofer channels. It is the
  • Страница 73 из 97
    English STEP 3 : Connect the front channels to back audio panel's "Line Out", the rear channels to SURROUND-KIT's REAR R/L, and the Center/Subwoofer channels to SURROUND-KIT's SUB CENTER. STEP 4 : Click the audio icon "Sound Effect" from the windows tray at the bottom of the screen. STEP 5 : Select
  • Страница 74 из 97
    English SPDIF Output Device (Optional Device) A "S/PDIF output" device is available on the motherboard. Cable with rear bracket is provided and could link to the "S/PDIF output" connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting
  • Страница 75 из 97
    Jack-Sensing provides audio connectors error-detection function. Install Microsoft DirectX8.1 before to enable Jack-Sensing support for Windows 98/98SE/2000 /ME. Jack-Sensing includes 2 parts: AUTO and MANUAL. Following is an example for 2 channels (Windows XP): Introduction of audio connectors You
  • Страница 76 из 97
    English If you set wrong with the connectors, the warning message will come out as right picture. Manual setting: If the device picture shows different from what you set, please press "Manual Selection" to set. GA-8IE2004 Series Motherboard - 72 -
  • Страница 77 из 97
    English - 73 - Technical Reference
  • Страница 78 из 97
    English GA-8IE2004 Series Motherboard - 74 -
  • Страница 79 из 97
    English Revision History Chapter 5 Appendix Install Drivers Pictures below are shown in Windows XP Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
  • Страница 80 из 97
    English Driver installation finished ! You have to reboot system ! Item Description Intel Chipset Software Installation Utility Tell the operating system how the chipset components will be configured. Intel Application Accelerator Designed to improve performance of the storage sub-system and
  • Страница 81 из 97
    This page reveals the value-added software developed by Gigabyte and its worldwide partners. Gigabyte Windows Utilities Manager (GWUM) This utility can integrate the Gigabyte's applications in the system tray Gigabyte Management Tool (GMT) A useful tool which can manage the computer via the network
  • Страница 82 из 97
    English SOFTWARE INFORMATION This page list the contects of softwares and drivers in this CD title. HARDWARE INFORMATION This page lists all device you have for this motherboard. CONTACT US Please see the last page for details. GA-8IE2004 Series Motherboard - 78 -
  • Страница 83 из 97
    English EasyTune 4 Utilities Installation Powerful utility that integrates the overclocking and hardware monitoring functions 1. Click "EasyTune4" item. 2. Click "Next". (2) (1) 4. Right Click the icon to start "EasyTune 4". 3. Click "Finish" to restart computer. (4) (3) 5. Click "HELP". - 79 -
  • Страница 84 из 97
    English FAQ Below is a collection of general asked questions. To check general asked questions based on a specific motherboard model, please log on to http://tw.giga-byte.com/faq/faq.htm Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why? Answer: Some
  • Страница 85 из 97
    Answer: Please remember to load Fail-Safe Defaults (Or Load BIOS Defaults) after flashing BIOS. However, if the system instability still remains, please clear CMOS to solve the problem. Question 7: Why do I still get a weak sound after turning up the speaker to the maximum volume? Answer: Please
  • Страница 86 из 97
    English Question 11: How to set in the BIOS in order to bootup from SATA HDDs by either RAID or ATA mode? Answer: Please set in the BIOS as follow: 1. Advanced BIOS features--> SATA/RAID/SCSI boot order: "SATA" 2. Advanced BIOS features--> First boot device: "SCSI" 3. Integrated Peripherals-->
  • Страница 87 из 97
    If you encounter any trouble during boot up, please follow the troubleshooting procedures. START Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ? Yes Please isolate the short
  • Страница 88 из 97
    English A Is memory LED on and CPU fan running? No The problem could be caused by power supply, CPU, memory or CPU/memory socket itself. Yes Failure has been excluded. No Check if there is display. Yes Perhaps your VGA card / VGA slot or monitor is defective. Failure has been excluded. Turn off the
  • Страница 89 из 97
    Customer/Country: Contact Person: Company: E-mail Add. : Phone No.: Model name/Lot Number: BIOS version: Hardware Configuration English Technical Support/RMA Sheet PCB revision: O.S./A.S.: Mfs. Model name Size: Driver/Utility: CPU Memory Brand Video Card Audio Card HDD CD-ROM / DVD-ROM Modem
  • Страница 90 из 97
    English Acronyms Acronyms ACPI APM AGP Meaning Advanced Configuration and Power Interface Advanced Power Management Accelerated Graphics Port AMR ACR BIOS CPU Audio Modem Riser Advanced Communications Riser Basic Input / Output System Central Processing Unit CMOS CRIMM CNR DMA Complementary Metal
  • Страница 91 из 97
    Meaning IOAPIC ISA LAN I/O Input Output Advanced Programmable Input Controller Industry Standard Architecture Local Area Network Input / Output LBA LED MHz MIDI Logical Block Addressing Light Emitting Diode Megahertz Musical Instrument Digital Interface MTH MPT NIC OS Memory Translator Hub Memory
  • Страница 92 из 97
    English GA-8IE2004 Series Motherboard - 88 -
  • Страница 93 из 97
    English - 89 - Memo
  • Страница 94 из 97
    English GA-8IE2004 Series Motherboard - 90 -
  • Страница 95 из 97
    English - 91 - Memo
  • Страница 96 из 97
    English CONTACT US Contact us via the information in this page all over the world. Taiwan The Netherlands Gigabyte Technology Co., Ltd. Giga-Byte Technology B.V. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, R.O.C. Address: Verdunplein 8 5627 SZ, Eindhoven, The Netherlands TEL:
  • Страница 97 из 97