Инструкция для GIGABYTE GA-8IG1000MF-P, GA-8IG1000MF

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

When you installing AGP card, please make sure the following notice
is fully understood and practiced.  If your AGP card has "AGP 4X/8X
(1.5V) notch"(show below), please make sure your AGP card is AGP
4X/8X (1.5V).

Caution: AGP 2X card is not supported by Intel

®

 845(GE/PE) / 845(E/G) /

850(E) / E7205 / 865(G/PE/P) / 875P. You might experience system
unable to boot up normally. Please insert an AGP 4X/8X card.

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X
mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X(1.5V) mode
by adjusting the jumper. The factory default for this card is 2X(3.3V).
The GA-8IG1000MF Series (or any AGP 4X/8X only) motherboards might not
function properly, if you install this card without switching the jumper to
4X(1.5V) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color",
the graphics card manufacturer & some SiS 305 cards, their golden finger is
compatible with 2X(3.3V)/4X(1.5V) mode AGP slot, but they support 2X(3.3V)
only. The GA-8IG1000MF Series (or any AGP 4X/8X only) motherboards might
not function properly, If you install this card in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage
128 Pro chip, the design of AG32S(G) is compliance with AGP 4X(1.5V)
specification. Therefore, AG32S(G) will work fine with Intel

®

 845(GE/PE) /

845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P

 

based motherboards.

AGP 4X/8X notch

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
Оглавление инструкции
  • Страница 1 из 105
    When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1.5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1.5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G)
  • Страница 2 из 105
    The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Please do not remove any labels on
  • Страница 3 из 105
    Declaration of Conformity We, Manufacturer/Importer (full address) G.B.T. Technology Träding GMbH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-8IG1000MF / GA-8IG1000MF-P is in
  • Страница 4 из 105
    DECLARATION OF CONFORMITY Per FCC Part 2 Section 2.1077(a) Responsible Party Name: G.B.T. INC. (U.S.A.) Address: 17358 Railroad Street City of Industry, CA 91748 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Motherboard Model Number: GA-8IG1000MF /
  • Страница 5 из 105
    GA-8IG1000MF Series P4 Titan Series Motherboard USER'S MANUAL Pentium® 4 Processor Motherboard Rev. 1002 12ME-8IG1KMF-1002
  • Страница 6 из 105
    English Table of Contents Item Checklist ......................................................................................... 4 Chapter 1 Introduction ............................................................................ 5 Features Summary
  • Страница 7 из 105
    English Frequency/Voltage Control ........................................................................ 50 Load Fail-Safe Defaults ............................................................................. 52 Load Optimized Defaults
  • Страница 8 из 105
    English Item Checklist The GA-8IG1000MF Series motherboard Serial ATA cable 2 Port USB Cable x 1 CD for motherboard driver & utility 4 Port USB Cable x 1 SPDIF Kit x 1 (SPDIF Out Kit) GA-8IG1000MF Series user's manual Quick PC Installation Guide SATA RAID Manual GC-SATA Card (optional) IEEE 1394
  • Страница 9 из 105
    Features Summary Form Factor Motherboard CPU Chipset Memory I/O Control Slots On-Board IDE Serial ATA On-Board Peripherals Hardware Monitor 24.3cm x 24.3cm Micro ATX size form factor, 4 layers PCB GA-8IG1000MF or GA-8IG1000MF-P Socket 478 for Intel® Micro FC-PGA2 Pentium® 4 processor Supports
  • Страница 10 из 105
    English On-Board LAN On-Board Sound On-Board IEEE1394 PS/2 Connector BIOS Additional Features GA-8IG1000MF: Built in Intel® 82562EZ chipset; Data transfer rate 10/100 supported GA-8IG1000MF-P: Built in Intel® 82547EI(KENAI II CSA) chipset; Data transfer rate 10/100/1000 supported 1 RJ45 port
  • Страница 11 из 105
    KB_MS English GA-8IG1000MF Series Motherboard Layout ATX R_USB FDD -P* RAM_LED LPT COMA CPU_FAN GA-8IG1000MF IDE2 Intel 865G IT8712F AGP CD_IN AUX_IN# DDR4 2X_DET DDR3 COMB DDR1 AUDIO1 IDE1 Intel 82547EI* 82562EZ# LAN USB ATX_12V DDR2 VGA SOCKET 478 BAT PCI1 SYS _FAN SUR_CEN Intel ICH5 PCI2 #
  • Страница 12 из 105
    English Block Diagram Pentium 4 Socket 478 CPU RJ45* AGP 4X/8X AGPCLK (66MHz) Intel KENAI II CSA* CPUCLK+/- (100/133/200MHz) System Bus 800/533/400MHz 266/333/400MHz DDR RAM Intel 865G MCHCLK (100/133/200MHz) 66 MHz 33 MHz 14.318 MHz 48 MHz Intel 82562EZ # 3 PCI RJ45 # BIOS Intel ICH5 Game Port LPC
  • Страница 13 из 105
    English Chapter 2 Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 1 Step
  • Страница 14 из 105
    English Step 1: Install the Central Processing Unit (CPU) Before installing the processor, adhere to the following warning: 1. Please make sure the CPU type is supported by the motherboard. 2. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause improper installation.
  • Страница 15 из 105
    Before installing the CPU cooling fan, adhere to the following warning: 1. Please use Intel approved cooling fan. 2. We recommend you to apply the thermal tape to provide better heat conduction between your CPU and cooling fan. (The CPU cooling fan might stick to the CPU due to the hardening of the
  • Страница 16 из 105
    English Step 2: Install Memory Modules Before installing the memory modules, adhere to the following warning: 1. When RAM_LED is ON, do not install / remove DIMM from socket. 2. Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause
  • Страница 17 из 105
    Established on the existing SDRAM industry infrastructure, DDR (Double Data Rate) memory is a high performance and cost-effective solution that allows easy adoption for memory vendors, OEMs and system integrators. DDR memory is a sensible evolutionary solution for the PC industry that builds on the
  • Страница 18 из 105
    English The following tables include all memory-installed combination types: (Please note that those types not in the tables will not boot up.) Figure 1: Dual Channel Technology (DS: Double Side, SS: Single Side) DIMM 1 4 memory modules DIMM 2 DIMM 3 DS/SS X DS/SS X X 2 memory modules DIMM 4 DS/SS
  • Страница 19 из 105
    Step 4-1: I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse Connector PS/2 Mouse Connector (6 pin Female) This connector supports standard PS/2 keyboard and PS/2 mouse. PS/2 Keyboard Connector (6 pin Female) / Before you connect your device(s) into USB connector(s), please make sure your
  • Страница 20 из 105
    English Parallel Port, Serial Port and VGA port (LPT / COMA / VGA) Parallel Port (25 pin Female) COMA Serial Port (9 pin Male) This connector supports 1 standard COM port , 1 Parallel port and 1 VGA port. Device like printer can be connected to Parallel port; mouse and modem etc. can be connected
  • Страница 21 из 105
    1 3 11 English Step 4-2: Connectors Introduction 2 5 6 12 20 16 14 8 4 24* 25 # 15# 7 17* 13 22 21 23 19 18 10 9 1) ATX_12V 14) CD_IN 2) ATX 3) CPU_FAN 15) AUX_IN# 16) SUR_CEN 4) SYS_FAN 5) FDD 17) SPDIF_IO* 18) F_USB1 / F_USB2 6) IDE1 / IDE2 7) SATA0 / SATA1 19) F1_1394 / F2_1394 20) COMB 8) BAT
  • Страница 22 из 105
    English 1) ATX_12V (+12V Power Connector) This connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this "ATX_12V connector" is not connected, system cannot boot. Pin No. _ Definition 1 3 1 GND 2 3 GND +12V 4 2 4 +12V 2) ATX (ATX Power) AC power cord should only be connected to your
  • Страница 23 из 105
    Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating. The CPU fan connector supports Max. current up to 600 mA. 1 Pin No. Definition 1 GND 2 3 +12V Sense 4) SYS_FAN (System Fan Connector) This connector
  • Страница 24 из 105
    English 5) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and 2.88M bytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1. 34 33 2 1 6) IDE1 / IDE2 (IDE1 / IDE2 Connector) Important Notice:
  • Страница 25 из 105
    You can connect the Serial ATA device to this connector, it provides you high speed transfer rates (150MB/sec). Pin No. 7 1 GND 2 SATA1 7 Definition 1 1 TXP 3 4 TXN GND 5 RXN 6 RXP 7 SATA0 GND 8) BAT (BATTERY) + CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the
  • Страница 26 из 105
    Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront panel to the F_PANEL connector according to the pin assignment above. Speaker Connector Message LED/ Power/ Sleep LED 2 1 1 SPEAK- SPEAK+ MSG+ MSGPW+ PW- Soft Power Connector 1 1 1 20 19 RES+ NC HD+ HD-
  • Страница 27 из 105
    PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color. 1 Pin No. Definition 1 MPD+ 2 MPD- 3 MPD- 11) RAM_LED + _ Do not remove memory modules
  • Страница 28 из 105
    _ When an AGP 2X (3.3V) card is installed the 2X_DET will light up, indicating a non-supported graphics card is inserted. Informing users that system might not boot up normally due to AGP 2X (3.3V) is not supported by the chipset. + English 12) 2X_DET 13) F_AUDIO (Front Audio Connector) If you want
  • Страница 29 из 105
    English 14) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. Definition 1 2 CD-L GND 3 GND 4 1 CD-R 15) AUX_IN (AUX In Connector)# Connect other device (such as PCI TV Tunner audio out) to the connector. Pin No. Definition 1 2 AUX-L GND 3 GND 4 1 AUX-R * For
  • Страница 30 из 105
    English 16) SUR_CEN (Surround Center Connector) Please contact your nearest dealer for optional SUR_CEN cable. Pin No. Definition 1 No Pin 5 CENTER_OUT 6 1 5 SUR OUTR GND 4 2 6 SUR OUTL 2 3 BASS_OUT 17) SPDIF_IO (SPDIF In / Out Connector)* The SPDIF output is capable of providing digital audio to
  • Страница 31 из 105
    Be careful with the polarity of the front USB connector. Check the pin assignment while you connect the front USB cable. Please contact your nearest dealer for optional front USB cable. 10 9 10 9 F_USB1 F_USB2 2 1 2 1 Pin No. Definition 1 Power 2 3 Power USB Dx- 4 USB Dy- 5 USB Dx+ 6 7 USB Dy+ GND
  • Страница 32 из 105
    English 20) COMB (COM B Connector) Be careful with the polarity of the COMB connector. Check the pin assignment while you connect the COMB cable. Please contact your nearest dealer for optional COMB cable. Pin No. NSINB 3 4 NSOUTB NDTRB- 5 GND 6 NDSRB- 7 8 2 1 NDCDB- 2 10 9 Definition 1 NRTSBNCTSB-
  • Страница 33 из 105
    This connector supports joystick, MIDI keyboard and other relate audio devices. Pin No. Definition 1 2 16 VCC 2 GRX1_R 3 4 GND GPSA2 GPX2_R 7 8 GPY2_R MSI_R 9 15 VCC 6 1 5 GPSA1 10 GND 11 12 GPY1_R VCC 13 GPSB1 14 MSO_R 15 16 GPSB2 No Pin 23) INFO_LINK This connector allows you to connect some
  • Страница 34 из 105
    English 24) CLR_CMOS (Clear CMOS)* You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily shor 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper. 1 1-2 close: Clear CMOS 1 Open: Normal 25) CI (Chassis Intrusion, Case Open)#
  • Страница 35 из 105
    BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the computer
  • Страница 36 из 105
    English GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the
  • Страница 37 из 105
    English Integrated Peripherals This setup page includes all onboard peripherals. Power Management Setup This setup page includes all the items of Green function features. PnP/PCI Configurations This setup page includes all the configurations of PCI & PnP ISA resources. PC Health Status This setup
  • Страница 38 из 105
    English Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Date (mm:dd:yy) Mon, Sep 29 2003 Time (hh:mm:ss) 22:31:24 Item Help Menu Level Change the day, month, IDE Primary Master [None] IDE Primary Slave [None] year IDE Secondary Master [None]
  • Страница 39 из 105
    The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. IDE Primary Master, Slave / IDE Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the
  • Страница 40 из 105
    English Floppy 3 Mode Support (for Japan Area) Disabled Normal Floppy Drive. (Default value) Drive A Drive A is 3 mode Floppy Drive. Drive B Drive B is 3 mode Floppy Drive. Both Drive A & B are 3 mode Floppy Drives. Halt on The category determines whether the computer will stop if an error is
  • Страница 41 из 105
    English Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Advanced BIOS Features Hard Disk Boot Priority [Press Enter] Item Help First Boot Device [Floppy] Menu Level Second Boot Device [Hard Disk] Select Boot Device Third Boot Device [CDROM] Priority Password Check
  • Страница 42 из 105
    English USB-ZIP Select your boot device priority by USB-ZIP. USB-CDROM Select your boot device priority by USB-CDROM. USB-HDD Select your boot device priority by USB-HDD. LAN Select your boot device priority by LAN. Disabled Select your boot device priority by Disabled. Password Check Setup The
  • Страница 43 из 105
    English Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Integrated Peripherals On-Chip Primary PCI IDE [Enabled] Item Help On-Chip Secondary PCI IDE [Enabled] Menu Level [Auto] If a hard disk x SATA Port0 Configure as On-Chip SATA SATA Port0 controller card is SATA
  • Страница 44 из 105
    English On-Chip Primary PCI IDE Enabled Enable onboard 1st channel IDE port. (Default value) Disabled Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE Enabled Enable onboard 2nd channel IDE port. (Default value) Disabled Disable onboard 2nd channel IDE port. On-chip SATA Disabled
  • Страница 45 из 105
    English USB 2.0 Controller Disable this function if you are not using onboard USB 2.0 feature. Enabled Enable USB 2.0 Controller. (Default value) Disabled Disable USB 2.0 Controller. USB Keyboard Support Enabled Enable USB Keyboard Support. Disabled Disable USB Keyboard Support. (Default value) USB
  • Страница 46 из 105
    English Onboard Serial Port 1 Auto BIOS will automatically setup the port 1 address. 3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default value) 2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8. 3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8. 2E8/IRQ3 Enable onboard
  • Страница 47 из 105
    This feature allows you to select from a given set of parameters if the parallel port uses the onboard I/O controller. Disabled Disable onboard LPT port. 378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value) 278/IRQ5 Enable onboard LPT port and address is 278/IRQ5. 3BC/IRQ7
  • Страница 48 из 105
    English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type [S1(POS)] Item Help Power LED in S1 state [Blinking] Menu Level Off by Power button [Instant-off] [S1] PME Event Wake Up [Enabled] Set suspend type to
  • Страница 49 из 105
    Instant-off Press power button then Power off instantly. (Default value) Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up Disabled Disable this function. Enabled Enable PME Event Wake up. (Default Value) ModemRingOn/WakeOnLAN
  • Страница 50 из 105
    English Power On By Keyboard This feature allows you to set the method for powering-on the system. The option "Password" allows you to set up to 5 alphanumeric characters to power-on the system. The option "Keyboard 98" allows you to use the standard keyboard 98 to power on the system. Password
  • Страница 51 из 105
    English PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PnP/PCI Configurations PCI 1 IRQ Assignment [Auto] Item Help PCI 2 IRQ Assignment [Auto] Menu Level PCI 3 IRQ Assignment [Auto] : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous
  • Страница 52 из 105
    English PC Health Status CMOS Setup Utility-Copyright (C) 1984-2003 Award Software PC Health Status Reset Case Open Status [Disabled] Item Help Case Opened Yes Menu Level Vcore OK [Disabled] DDR25V OK Don't reset case +3.3V OK open status +5V OK +12V OK [Enabled] o Current CPU Temperature 33 C
  • Страница 53 из 105
    English Current Voltage (V) Vcore / DDR25V / +3.3V / +5V / +12V Detect system's voltage status automatically. Current CPU Temperature Detect CPU temperature automatically. Current CPU/SYSTEM FAN Speed (RPM) Detect CPU/SYSTEM fan speed status automatically. CPU Warning Temperature 60 oC / 140 o F 70
  • Страница 54 из 105
    English Frequency/Voltage Control CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Frequency/Voltage Control CPU Clock Ratio [15X] Item Help CPU Host Clock Control [Disabled] Menu Level CPU Host Frequency (Mhz) 100 AGP/PCI/SRC Fixed 66/33/100 Memory Frequency For [Auto] Memory Frequency
  • Страница 55 из 105
    100MHz ~ 355MHz Set CPU Host Clock from 100MHz to 355MHz. Incorrect using it may cause your system broken. For power End-User use only! AGP/PCI/SRC Fixed Serial ATA device is very sensitive to SRC clock. SRC over clock may make Serial ATA device function can't work properly. Adjust AGP/PCI/SRC
  • Страница 56 из 105
    English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Load Power Management Setup Fail-Safe Defaults (Y/N) ? Password Set
  • Страница 57 из 105
    English Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Load Power Management Setup Optimized Defaults (Y/N) ?Password Set
  • Страница 58 из 105
    English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Enter Password : Power Management Setup Set User Password
  • Страница 59 из 105
    English Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password (Y/N) ? Y Power Management Save to CMOS and EXITSet User Password Setup
  • Страница 60 из 105
    English Exit Without Saving CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Standard CMOS Features Load Fail-Safe Defaults Advanced BIOS Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Quit Power Management Setup Without Saving (Y/N) ? N Password Set User
  • Страница 61 из 105
    English Chapter 4 Technical Reference @BIOS™ Introduction Gigabyte announces @BIOS™ Windows BIOS live update utility Have you ever updated BIOS by yourself? Or like many other people, you just know what BIOS is, but always hesitate to update it? Because you think updating newest BIOS is unnecessary
  • Страница 62 из 105
    English EasyTune™ 4 Introduction Gigabyte announces EasyTune™ 4 Windows based Overclocking utility EasyTune 4 carries on the heritage so as to pave the way for future generations. Overclock might be one of the most common issues in computer field. But have many users ever tried it? The answer is
  • Страница 63 из 105
    Method 1 : Q-Flash™ Utility Q-Flash™ is a BIOS flash utility embedded in Flash ROM. With this utility, users only have to stay in the BIOS menu when they want to update BIOS. Q-Flash™ allows users to flash BIOS without any utility in DOS or Windows. Using Q-Flash ™ indicating no more fooling around
  • Страница 64 из 105
    English Part One: Updating BIOS with Q-Flash™ Utility on Dual BIOS Motherboards. Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards supporting Q-Flash™ and Dual BIOS, the Q-Flash™ utility and Dual BIOS utility are combined in the same screen. This
  • Страница 65 из 105
    AMIBIOS SIMPLE SETUP UTILITY - VERSION 2.00 (C) 2001 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP HARDWARE MONITOR & MISC SETUP CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP USER PASSWORD ENTER DUAL BIOS/Q-FLASH
  • Страница 66 из 105
    English Task menu for Dual BIOS utility: Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task. Task menu for Q-Flash™ utility: Contains the names of four tasks. Blocking a
  • Страница 67 из 105
    2. Move to the BIOS file you want to flash and press Enter. In this example, we only download one BIOS file to the floppy disk so only one BIOS file, 7VRXP.F12, is listed. Please confirm again you have the correct BIOS file for your motherboard. Dual BIOS Utility Boot
  • Страница 68 из 105
    English After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?" Dual BIOS Utility Boot From......................................... Main Bios Main ROM Type/Size........................ SST 49LF003A Backup ROM Type/Size.................... SST
  • Страница 69 из 105
    Dual BIOS Utility Boot From......................................... Main Bios Main ROM Type/Size........................ SST 49LF003A Backup ROM Type/Size.................... SST 49LF003A 256K 256K Wide Range Protection Disable Boot From Main Bios Auto Recovery Enable Halt On Error Disable Copy
  • Страница 70 из 105
    English After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed. American Release:08/23/2002 Megatrends AMIBIOS (C) 1999 American Megatrend 7VRXP F12 The BIOS file becomes F12 after updating AMD-Athlon(tm)Processor-1333MHz Check System Health ! Checking
  • Страница 71 из 105
    STANDARD CMOS SETUP INTEGRATED PERIPHERALS BIOS FEATURES SETUP HARDWARE MONITOR & MISC SETUP CHIPSET FEATURES SETUP SUPERVISOR PASSWORD POWER MANAGEMENT SETUP PNP / PCI CONFIGURATION USER PASSWORD Load Fail-Safe Defaults HDD AUTO DETECTION IDE (Y/N)? Y LOAD FAIL-SAFE DEFAULTS Press Y on your
  • Страница 72 из 105
    English Part Two: Updating BIOS with Q-Flash ™ Utility on Single-BIOS Motherboards. This part guides users of single-BIOS motherboards how to update BIOS using the Q-Flash™ utility. Entering the Q-Flash™ utility: Step1: To use the Q-Flash™ utility, you must press Del in the boot screen to enter
  • Страница 73 из 105
    The Q-Flash™ BIOS utility screen consists of the following key components. Q-Flash Utility V1.30 Flash Type/Size................SST 49LF002A 256K The Q-Flash utility title bar Keep DMI DataEnable Update BIOS from Floppy Save BIOS to Floppy Task menu for the Q-Flash utility Enter: Run / : Move ESC:
  • Страница 74 из 105
    English Later, you will see a box showing the BIOS files you downloaded to the floppy disk. In this example, we only download one BIOS for this board, 8GE800.F4 so only one BIOS file is listed. 2.Highlight the BIOS file you want to flash and press Enter button on your keyboard to enable reading
  • Страница 75 из 105
    256K Keep DMI DataEnable CHECKSUM = AC03 AreUpdate BIOS update BIOS? you sure to from Floppy Save BIOS BIOS or [Enter] to continue updatingto Floppy "ESC" to abort. Enter: Run / : Move ESC: Reset F10:Power Off You can press "Enter" to continue updating BIOS or "ESC" to abort. 3. Press Y button if
  • Страница 76 из 105
    English Method 2 : @BIOS™ Utility If you don't have DOS boot disk, we recommend that you used Gigabyte @BIOS™ program to flash BIOS. Press here. 2. Click Start/ All Programs/ GIGABYTE/ @BIOS. 1. Click "@BIOS" item. (2) (1) 3.Click " ". Click here 4. Please select @BIOS sever site, then Click "OK".
  • Страница 77 из 105
    III. Save BIOS In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the current BIOS version. IV. Check out supported motherboard and Flash ROM: In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out which
  • Страница 78 из 105
    English 2- / 4- / 6-Channel Audio Function Introduction The installation of Windows 98SE/2K/ME/XP is very simple. Please follow next step to install the function! Stereo Speakers Connection and Settings: We recommend that you use the speaker with amplifier to acqiire the best sound effect if the
  • Страница 79 из 105
    English 4 Channel Analog Audio Output Mode STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In". Line Out Line In STEP 2 : After installation of the audio driver, you'll find an icon on the taskbar's status area. Click the audio icon "Sound Effect" from the windows tray
  • Страница 80 из 105
    English Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module. STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In", and the Center/Subwoofer channels to "MIC In". Line In MIC In STEP 2 : After
  • Страница 81 из 105
    (Audio Combo Kit provides SPDIF output port : optical & coaxis and SURROUND-KIT : Rear R/L & Center/subwoofer) SURROUND-KIT access analog output to rear channels and Center/Subwoofer channels. It is the best solution if you need 6 channel output, Line In and MIC at the same time. "SURROUND-KIT" is
  • Страница 82 из 105
    English STEP 3 : Connect the front channels to back audio panel's "Line Out", the rear channels to SURROUND-KIT's REAR R/L, and the Center/Subwoofer channels to SURROUND-KIT's SUB CENTER. STEP 4 : Click the audio icon "Sound Effect" from the windows tray at the bottom of the screen. STEP 5 : Select
  • Страница 83 из 105
    English SPDIF Output Device (Optional Device) A "S/PDIF output" device is available on the motherboard. Cable with rear bracket is provided and could link to the "S/PDIF output" connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting
  • Страница 84 из 105
    English Jack-Sensing Introduction Jack-Sensing provides audio connectors error-detection function. Install Microsoft DirectX8.1 before to enable Jack-Sensing support for Windows 98/98SE/2000 /ME. Jack-Sensing includes 2 parts: AUTO and MANUAL. Following is an example for 2 channels (Windows XP):
  • Страница 85 из 105
    English If you set wrong with the connectors, the warning message will come out as right picture. Manual setting: If the device picture shows different from what you set, please press "Manual Selection" to set. - 81 - Technical Reference
  • Страница 86 из 105
    English Xpress Recovery Introduction What is Xpress Recovery? Xpress Recovery utility is an utility for backing up and restoring O.S. partition . If the hard drive can not work properly, you can restore it to the original state. 1. It supports FAT16, FAT32, NTFS format. 2. It must be connected to
  • Страница 87 из 105
    Text Mode: Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technilogy CO. , Ltd. 1. Execute Backup Utility 2. Execute Restore Utility 3. Remove Backup Image 4. Exit and Restart BMP Mode: Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technilogy CO. , Ltd. 1. Execute Backup Utility 2. Execute
  • Страница 88 из 105
    English 1.Excute Backup Utility: Press B to Backup your System or Esc to Exit The Backup utility will scan the system automatically and back it up. The backed up data will be saved as a hidden image . 2.Excute Restore Utility: This program will recover your system to factory default. Press R to
  • Страница 89 из 105
    English Revision History Chapter 5 Appendix Install Drivers Pictures below are shown in Windows XP (IUCD ver 2.4) Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the
  • Страница 90 из 105
    English Driver installation finished ! You have to reboot system ! Item Description Intel Chipset Software Installation Utility Tell the operating system how the chipset components will be configured. Intel Extreme Graphics Driver For Intel® 845G/GL/GE/GV/865G Chipsets USB Patch for WinXP This
  • Страница 91 из 105
    This page reveals the value-added software developed by Gigabyte and its worldwide partners. Gigabyte Windows Utilities Manager (GWUM) This utility can integrate the Gigabyte's applications in the system tray Gigabyte Management Tool (GMT) A useful tool which can manage the computer via the network
  • Страница 92 из 105
    English SOFTWARE INFORMATION This page list the contects of softwares and drivers in this CD title. HARDWARE INFORMATION This page lists all device you have for this motherboard. CONTACT US Please see the last page for details. GA-8IG1000MF Series Motherboard - 88 -
  • Страница 93 из 105
    English EasyTune 4 Utilities Installation Powerful utility that integrates the overclocking and hardware monitoring functions 1. Click "EasyTune4" item. 2. Click "Next". (2) (1) 4. Right Click the icon to start "EasyTune 4". 3. Click "Finish" to restart computer. (4) (3) 5. Click "HELP". - 89 -
  • Страница 94 из 105
    English FAQ Below is a collection of general asked questions. To check general asked questions based on a specific motherboard model, please log on to http://tw.giga-byte.com/faq/faq.htm Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why? Answer: Some
  • Страница 95 из 105
    Question 7: Why do I still get a weak sound after turning up the speaker to the maximum volume? Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not, please change another speaker with power/amplifier and try again later. Question 8: How do I disable
  • Страница 96 из 105
    English Question 11: How to set in the BIOS in order to bootup from SATA HDDs by either RAID or ATA mode? Answer: Please set in the BIOS as follow: 1. Advanced BIOS features--> SATA/RAID/SCSI boot order: "SATA" 2. Advanced BIOS features--> First boot device: "SCSI" 3. Integrated Peripherals-->
  • Страница 97 из 105
    If you encounter any trouble during boot up, please follow the troubleshooting procedures. START Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ? Yes Please isolate the short
  • Страница 98 из 105
    English A Is memory LED on and CPU fan running? No The problem could be caused by power supply, CPU, memory or CPU/memory socket itself. Yes Failure has been excluded. No Check if there is display. Yes Perhaps your VGA card / VGA slot or monitor is defective. Failure has been excluded. Turn off the
  • Страница 99 из 105
    Customer/Country: Contact Person: Model name/Lot Number: BIOS version: Hardware Configuration CPU Memory Brand Video Card Audio Card HDD CD-ROM / DVD-ROM Modem Network AMR / CNR Keyboard Mfs. Company: E-mail Add. : English Technical Support/RMA Sheet Phone No.: PCB revision: O.S./A.S.: Model name
  • Страница 100 из 105
    English Acronyms Acronyms ACPI APM AGP AMR ACR BIOS CPU CMOS CRIMM CNR DMA DMI DIMM DRM DRAM DDR ECP ESCD Meaning Advanced Configuration and Power Interface Advanced Power Management Accelerated Graphics Port Audio Modem Riser Advanced Communications Riser Basic Input / Output System Central
  • Страница 101 из 105
    Meaning Input Output Advanced Programmable Input Controller Industry Standard Architecture Local Area Network Input / Output Logical Block Addressing Light Emitting Diode Megahertz Musical Instrument Digital Interface Memory Translator Hub Memory Protocol Translator Network Interface Card Operating
  • Страница 102 из 105
    English GA-8IG1000MF Series Motherboard - 98 -
  • Страница 103 из 105
    English - 99 - Appendix
  • Страница 104 из 105
    English CONTACT US Contact us via the information in this page all over the world. Taiwan The Netherlands Gigabyte Technology Co., Ltd. Giga-Byte Technology B.V. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, R.O.C. Address: Verdunplein 8 5627 SZ, Eindhoven, The Netherlands TEL:
  • Страница 105 из 105