Инструкция для GIGABYTE GA-8IP900MK

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

AGP 4X/8X notch

When you installing AGP card, please make sure the following notice
is fully understood and practiced.  If your AGP card has "AGP 4X/8X
(1.5V) notch"(show below), please make sure your AGP card is AGP
4X/8X (1.5V).

Caution: AGP 2X card is not supported by Intel

®

 845(GE/PE) / 845(E/G)

/ 850(E) / E7205 / 865(G/PE/P) / 875P. You might experience system
unable to boot up normally. Please insert an AGP 4X/8X card.

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X
mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X/8X(1.5V)
mode by adjusting the jumper. The factory default for this card is 2X(3.3V).
The GA-8IP900MK (or any AGP 4X/8X only) motherboards might not
function properly, if you install this card without switching the jumper to 4X/8X
(1.5) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color",
the graphics card manufacturer & some SiS 305 cards, their golden finger is
compatible with 2X(3.3V)/4X(1.5V) mode AGP slot, but they support 2X(3.3V)
only. The GA-8IP900MK (or any AGP 4X/8X only) motherboards might not
function properly, If you install this card in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage
128 Pro chip, the design of AG32S(G) is compliance with AGP 4X(1.5V)
specification. Therefore, AG32S(G) will work fine with Intel

®

 845(GE/PE) /

845(E/G) / 850(E) / E7205 / 865(G/PE/P) / 875P

 

based motherboards.

8ip900mk_1001_f.p65

2003/4/22, 下午 03:51

93

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Оглавление инструкции
  • Страница 1 из 97
    When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1.5V) notch"(show below), please make sure your AGP card is AGP 4X/8X (1.5V). AGP 4X/8X notch Caution: AGP 2X card is not supported by Intel® 845(GE/PE) / 845(E/G)
  • Страница 2 из 97
    The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners. Please do not remove any labels on
  • Страница 3 из 97
    Declaration of Conformity We, Manufacturer/Importer (full address) G.B.T. Technology Träding GMbH Ausschlager Weg 41, 1F, 20537 Hamburg, Germany declare that the product ( description of the apparatus, system, installation to which it refers) Mother Board GA-8IP900MK is in conformity with
  • Страница 4 из 97
    DECLARATION OF CONFORMITY Per FCC Part 2 Section 2.1077(a) Responsible Party Name: G.B.T. INC. (U.S.A.) Address: 17358 Railroad Street City of Industry, CA 91748 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Motherboard ModelNumber:GA-8IP900MK Conforms
  • Страница 5 из 97
    GA-8IP900MK P4 Titan Series Motherboard USER'S MANUAL Pentium® 4 Processor Motherboard Rev. 1001 12ME-8IP900MK-1001
  • Страница 6 из 97
    English Table of Content Item Checklist ..................................................................................4 Chapter 1 Introduction ......................................................................5 Features
  • Страница 7 из 97
    Chapter 4 Technical Reference ....................................................... 61 @BIOS™ Introduction ........................................................................................ 61 EasyTune™ 4 Introduction
  • Страница 8 из 97
    English Item Checklist The GA-8IP900MK motherboard GA-8IP900MK user's manual Quick PC Installation Guide SATA RAID Manual GC-SATA Card (opti onal) Serial ATA cable x 2 2 Port USB Cable x 1 4 Port USB Cable x 1 SPDIF Kit x 1 (SPDIF Out Kit) IEEE 1394 Cable x1 Audio Combo Kit x 1 (Manual; SATA cable
  • Страница 9 из 97
    Features Summary Form Factor CPU Chipset Memory I/O Control Slots On-Board IDE Serial ATA On-Board Peripherals Hardware Monitor On-Board LAN — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 24.4cm x 24.4cm Micro ATX size form factor, 4 layers PCB Socket 478 for Intel® Micro FC-PGA2
  • Страница 10 из 97
    English On-Board Sound PS/2 Connector BIOS Additional Features — — — — — — — — — — — — — — — — — Realtek ALC655 codec Supports Jack S ensing function Line Out / 2 front speaker Line In / 2 rear speaker (by s/w sw itch) Mic In / center & subwoofer (by s/w switch) CD In / AUX In / Game port PS/2 K
  • Страница 11 из 97
    KB_MS English GA-8IP900MK Motherboard Layout ATX R_USB FDD DIMM_LED LPT COMA CPU_FAN Intel 865P AUDIO1 CD_IN AUX_IN DDR4 DDR3 AGP DDR2 DDR1 IDE2 2X_DET ITE 8712F BAT PCI1 CLR_PWD SUR_CEN PCI2 SYS _FAN Intel ICH5 SATA1 CODEC F_AUDIO PCI3 GAME IDE1 Intel 82562EZ GA-8IP900MK ATX_12V LAN USB COMB
  • Страница 12 из 97
    Pentium 4 Socket 478 CPU AGP 4X/8X CPUCLK+/- (100/133 MHz) Sy stem Bus 533/400MHz AGPCLK (66MHz) 266/333MHz DDR RAM Intel 865P MCHCLK (100/133 MHz) 66 MHz 33 MHz 14.318 MHz 48 MHz Intel 82562EZ RJ45 3 PCI BIOS Intel ICH5 Game Port LPC BUS Floppy AC97 Link IT8712F LPT Port PS/2 KB/Mouse 24 MHz
  • Страница 13 из 97
    English -9- Introduction
  • Страница 14 из 97
    English GA-8IP900MK Motherboard - 10 -
  • Страница 15 из 97
    English Chapter 2 Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Connect ribbon cables, cabinet wires, and power supply Step 1 Step
  • Страница 16 из 97
    English Step 1: Install the Central Processing Unit (CPU) Before in stalling the pro cessor, adhere t o the following warning: 1. Please make sure the CPU type is supported by the moth erboard. 2. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause imp roper installation.
  • Страница 17 из 97
    Before installing the CPU cooling fan, adhere to t he following warning: 1. Please use Intel approved co oling fan. 2. We recommend you to app ly the thermal tape to pro vide b etter heat conduction between you r CPU and cooling fan. (The C PU cooling fan might stick to the CPU due to the harden
  • Страница 18 из 97
    English Step 2: Install Memory Modules Before in stalling the memo ry modules, adhere to the following warning: 1. When DIMM LED is ON, do not install / remove DIMM from socket. 2. Please no te that the DIMM module can only f it in one direction due to th e on e no tch . Wrong orientatio n will
  • Страница 19 из 97
    Established on the ex isting SDRAM industry infrastructure, DDR (Double Data R ate) memory is a high performance and cos t-effec tiv e s olution that allow s easy adoption for mem ory v endors, OEMs and sy stem integrators. DDR memory is a sensible ev olutionary solution for the PC industry that
  • Страница 20 из 97
    English 4. Four DDR memory modules are installed: If y ou install four memory modules at the same time, the Dual Channel Technology w ill operate only w hen those modules hav e the same memory size and ty pe. The follow ing tables inc lude all m emory -installed com bination ty pes: (Please note
  • Страница 21 из 97
    Step 4-1: I/O Back Panel Introduction y w u x v u PS/2 Keyboard and PS/2 Mouse Connector PS/2 Mouse Connector (6 pin Female) This connector supports standard P S / 2 keyboard and PS/2 mouse. PS/2 Keyboard Connector (6 pin Female) v/x USB/LAN Connector LAN USB 0 USB 2 USB 1 USB 3 Before you connect
  • Страница 22 из 97
    English w Parallel Port and Serial Ports (COMA/COMB) Parallel Port (25 pin Female) COMA This connector supports 2 standard COM ports and 1 Parallel port. Device like printer can be connected to Parallel port ; mouse and modem etc can be connected to Serial ports. COMB Serial Port (9 pin Male) y
  • Страница 23 из 97
    1 3 11 English Step 4-2: Connectors Introduction 2 5 6 12 8 4 14 15 21 7 13 16 19 18 20 17 22 10 9 1) ATX_12V 12) 2X_DET 2) ATX 13) F_AUDIO 3) CPU_FAN 14) CD_IN 4) SYS_FAN 15) AUX_IN 5) FDD 16) SUR_CEN 6) IDE1 / IDE2 17) F_USB1 / F_USB2 7) SATA0 / SATA1 18) IR_CIR 8) BAT 19) GAME 9) F_PANEL 20)
  • Страница 24 из 97
    English 1) ATX_12V (+12V Power Co nnector) This connector (ATX_12V) supplies the CPU operation v oltage (Vc ore). If this "ATX_12V connec tor" is not connected, sy stem cannot boot. Pin No. Definition 1 3 GND 2 GND 3 +12V 4 2 4 1 +12V 2) ATX (ATX Power) AC pow er cord should only be connected to y
  • Страница 25 из 97
    Pleas e note, a proper installation of the CPU cooler is essential to prev ent the CPU from running under abnormal condition or damaged by ov erheating. The CPU fan connector supports M ax . current up to 600 mA. 1 Pin No. Definition 1 GND 2 +12V 3 Sense 4) SYS_FAN (System Fan Co nnector) This
  • Страница 26 из 97
    English 5) FDD (Floppy Connector) Pleas e connect the floppy driv e ribbon cables to FDD. It supports 360K, 1.2M, 720K, 1.44M and 2.88M by tes floppy disk ty pes. The red stripe of the ribbon cable must be the same side w ith the Pin1. 34 33 2 1 6) IDE1 / ID E2 (IDE1 / IDE2 C onnector) Important
  • Страница 27 из 97
    You can connect the Serial ATA dev ice to this connector, it prov ides y ou high speed transfer rates (150MB/sec). Pin No. 7 1 Definition SATA0 TXN 4 GND 5 RXN 6 RXP 7 1 TXP 3 7 GND 2 SATA1 1 GND 8) BAT (BATTERY) + CAUTION Danger of ex plos ion if battery is incorrectly replaced. Replace only w ith
  • Страница 28 из 97
    Please connect the pow er LED, PC speaker, reset sw itch and pow er sw itch etc of y our chassisfront panel to the F_PANEL connector according to the pin as signment abov e. Speak er Conne ctor Messag e LED/ Pow er/ Sleep LED 2 1 1 1 SPEAK- SPEAK+ MSG+ MSGPW+ PW- Soft Power Conne ctor 1 1 20 19
  • Страница 29 из 97
    PWR_LED is connec t w ith the sy stem pow er indicator to indicate w hether the sy stem is on/ off. It w ill blink w hen the sy stem enters suspend mode. If y ou use dual color LED, pow er LED w ill turn to another color. Pin No. Definition 1 MPD+ 2 MPD- 3 1 MPD- 11) DIMM_LED + _ Do not remov e
  • Страница 30 из 97
    _ When an AGP 2X (3.3V) card is ins talled the 2X_DET w ill light up, indicating a non-supported graphics card is inserted. Inform ing users that sy stem might not boot up normally due to AGP 2X (3.3V) is not s upported by the chipset. + English 12) 2X_DET 13) F_AUDIO (Front Audio Co nnector) If y
  • Страница 31 из 97
    English 14) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. Definition CD-L 2 GND 3 GND 4 1 1 CD-R 15) AUX_IN (AUX In Conn ector) Connect other dev ice (s uch as PC I TV Tunner audio out) to the connector. Pin No. GND GND 4 - 27 - AUX-L 2 3 1 Definition 1 AUX-R
  • Страница 32 из 97
    English 16) SUR_CEN ( Surround Center C onnector) Pleas e contact y our nearest dealer for optional SUR_CEN c able. Pin No. 2 6 Definition 1 SUR OUTR 3 GND 4 No Pin 5 CENTE R_OUT 6 1 5 SUR OUTL 2 BASS _OUT 17) F_USB1 / F_USB2 ( Front USB C onnector, Yellow) Be careful w ith the polarity of the
  • Страница 33 из 97
    Make sure the pin 1 on the IR dev ic e is aling w ith pin one the connector. To enable the IR /CIR function on the board, y ou are required to purchas e an option IR/CIR module. For detail information please contact y our autherized Gigaby te distributor. To use IR function only, please c onnect IR
  • Страница 34 из 97
    English 20) INFO_LINK This connector allow s y ou to connect som e ex ternal dev ices to prov ide y ou ex tra func tion. Pin No. Definition 1 SMBDATA GPIO 5 GND 6 GND No Pin 8 NC 9 +12V 10 9 VCC 7 1 10 3 4 2 SMB CLK 2 +12V 21) CI (CAS E OPEN) This 2-pin connector allow s y our sy stem to enable or
  • Страница 35 из 97
    When Jumper is set to "open" and sy stem is restarted, the pass w ord that is set w ill be cleared. On the contrary w hen Jumper is s et to "close", the current s tatus rem ains. Open: Clear Passw ord 1 Close: Normal 1 - 31 - Hardw are Installation Process English 22) CLR_PWD
  • Страница 36 из 97
    English GA-8IP900MK Motherboard - 32 -
  • Страница 37 из 97
    BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the computer
  • Страница 38 из 97
    English GETTING HELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the
  • Страница 39 из 97
    Integrated Peripherals English l This setup page includes all onboard peripherals. l Power Manag ement Setup This setup page includes all the items of Green function features. l PnP/PCI Configurations This setup page includes all the configurations of PCI & PnP ISA resources. l PC Health Status
  • Страница 40 из 97
    English Standard CMOS Features CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Standard CMOS Features Date (mm:dd:y y ) Sat, M ar 22 2003 Item Help Time (hh:mm :ss) 22:31:24 Menu Lev el u Change the day , month, }IDE Primary M aster [None] }IDE Primary Slav e [None] }IDE Secondary M
  • Страница 41 из 97
    The times format in < hour> <minute> <second> . The time is calculated base on the 24-hour military-time clock. For ex ample, 1 p.m. is 13: 00:00. IDE Primary Master, Slave / IDE Secondary Master, Slave The category identifies the ty pes of hard disk from driv e C to F that has been installed in
  • Страница 42 из 97
    English Floppy 3 Mode Support (for J apan Area) Disabled Normal Floppy Driv e. (Default v alue) Driv e A Driv e A is 3 mode Floppy Driv e. Driv e B Driv e B is 3 mode Floppy Driv e. Both Driv e A & B are 3 mode Floppy Driv es. Halt on The category determines whether the computer will stop if an
  • Страница 43 из 97
    English Advanced BIOS Features CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Adv anc ed BIOS Features First Boot Dev ice [Floppy ] Item Help Second Boot Dev ice [HDD-0] Menu Lev el u Third Boot Dev ice [CDR OM] Selec t Boot Dev ice Passw ord Check [Setup] Priority # CPU Hy
  • Страница 44 из 97
    English Password Check Setup The s y stem w ill boot but w ill not access to Setup page if the correct passw ord is not entered at the prompt. (Default v alue) Sy s tem The s y stem w ill not boot and w ill not acc ess to Setup page if the correct passw ord is not entered at the prompt. CPU
  • Страница 45 из 97
    English Integrated Peripherals CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Integrated Peripherals On-Chip Primary PCI IDE [Enabled] Item Help On-Chip Secondary PCI IDE [Enabled] Menu Lev el u On-Chip SATA [Auto] If a hard disk x SATA Port0 Configure as SATA Port0 controller card
  • Страница 46 из 97
    English On-Chip Primary PCI IDE Enabled Enable onboard 1st channel IDE port. (Default v alue) Disabled Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE Enabled Enable onboard 2nd channel IDE port. (Default v alue) Disabled Disable onboard 2nd channel IDE port. On-chip SATA Disabled
  • Страница 47 из 97
    English USB 2.0 Controller Disable this function if y ou are not using onboard U SB 2.0 feature. Enabled Enable USB 2. 0 Controller. (Default v alue) Disabled Disable USB 2. 0 Controller. USB Keyboard Support Enabled Enable USB Key board Support. Disabled Disable USB Key board Support. (Default v
  • Страница 48 из 97
    English Onboard Serial Port 2 Auto BIOS w ill autom atically s etup the port 2 address. 3F8/ IRQ4 Enable onboard Serial port 2 and address is 3F8. 2F8/ IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default v alue) 3E8/ IRQ4 Enable onboard Serial port 2 and address is 3E8. 2E8/ IRQ3 Enable
  • Страница 49 из 97
    This feature allow s y ou to select Direc t Memory Access (DMA) channel if the ECP mode s elected. This function w ill av ailable w hen "Parallel Port Mode" set at ECP or ECP+EPP. 3 Set ECP Mode Use DMA to 3. (Default Value) 1 Set ECP Mode Use DMA to 1. Game Port Address 201 Set Game Port Address
  • Страница 50 из 97
    English Power Management Setup CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Pow er Management Setup ACPI Suspend Ty pe [S1(POS)] Item Help Pow er LED in S1 state [Blinking] Menu Lev el u Off by Pow er button [Instant-off] [S1] PME Ev ent Wak e Up [Enabled] Set s uspend ty pe to
  • Страница 51 из 97
    Instant-off Press pow er button then Pow er off instantly . (Default v alue) Delay 4 Sec. Press pow er button 4 sec. to Pow er off. Enter suspend if button is pressed less than 4 sec. PME Event Wake Up Disabled Disable this function. Enabled Enable PME Ev ent Wake up. (Default Value)
  • Страница 52 из 97
    English KB Power ON Password When "Pow er On by Key board" set at Passw ord, y ou can set the passw ord here. Enter Input passw ord (from 1 to 5 characters) and press Enter to set the Key board Pow er On pass w ord. AC BACK Function Soft-Off When AC-pow er back to the sy stem, the sy stem w ill be
  • Страница 53 из 97
    English PnP/PCI Configurations CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are PnP/PC I Configurations PCI 1 IRQ Assignment [Auto] Item Help PCI 2 IRQ Assignment [Auto] Menu Lev el u PCI 3 IRQ Assignment [Auto] higf: Mov e Enter:Select +/-/PU/ PD:Value F10:Sav e ESC:Ex it F 1:General
  • Страница 54 из 97
    English PC Health Status CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are PC Health Status Reset Case Open Status [Disabled] Item Help Case Opened Yes Menu Lev el u Vcore OK [Disabled] DDR 25V OK Don' t reset case +3.3V OK open s tatus +5V OK +12V OK [Enabled] Current CPU Temperature
  • Страница 55 из 97
    English Current CPU Temperature Detect CPU Temp. automatically. . Current CPU/SYSTEM FAN Speed (RPM) Detec t CPU/SYST EM Fan speed status automatic ally . CPU Warning Temperature 60oC / 140oF Monitor CPU Temp. at 60oC / 140oF. 70oC / 158oF Monitor CPU Temp. at 70oC / 158oF. 80 C / 176 F Monitor CPU
  • Страница 56 из 97
    English Frequency/Voltage Control CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are Frequency /Voltage Control CPU Clock R atio [15X] Item Help CPU Host Clock C ontrol [Disabled] Menu Lev el u ø CPU Host Frequency (Mhz) 133 ø AGP/PCI/SRC F ix ed 66/33/100 Memory Frequenc y For [Auto]
  • Страница 57 из 97
    100M Hz ~ 355MHz Set C PU Host Clock from 100MHz to 355MHz. Incorrect using it may c ause y our sy stem broken. For pow er End-User use only ! AGP/PCI/ SRC Fixed Serial ATA dev ice is v ery sensitiv e to SRC clock. SRC ov er clock may make Serial ATA dev ice function can't w ork properly . Adjus t
  • Страница 58 из 97
    English Load Fail-Safe Defaults CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are } Standard CMOS Features Load F ail-Safe Defaults } Adv anc ed BIOS Features Load Optimized Defaults } Integrated Peripherals Set Superv isor Passw ord Load ( Y/N) ? Y } Pow er Management Setup Fail-Safe
  • Страница 59 из 97
    English Load Optimized Defaults CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are } Standard CMOS Features Load F ail-Safe Defaults } Adv anc ed BIOS Features Load Optimized Defaults } Integrated Peripherals Set Superv isor Passw ord Load } Pow er Management Setup Optimized Defaults (
  • Страница 60 из 97
    English Set Supervisor/User Password CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are } Standard CMOS Features Load F ail-Safe Defaults } Adv anc ed BIOS Features Load Optimized Defaults } Integrated Peripherals Set Superv isor Passw ord Enter Password : } Pow er Management Setup Set U
  • Страница 61 из 97
    English Save & Exit Setup CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are } Standard CMOS Features Load F ail-Safe Defaults } Adv anc ed BIOS Features Load Optimized Defaults } Integrated Peripherals Set Superv isor Passw ord ( Y/N) ? Y } Pow er ManagementSave to CMOS and EXIT Set U
  • Страница 62 из 97
    English Exit Without Saving CMOS Setup Utility -Copy right (C) 1984-2003 Aw ard Softw are } Standard CMOS Features Load F ail-Safe Defaults } Adv anc ed BIOS Features Load Optimized Defaults } Integrated Peripherals Set Superv isor Passw ord Quit } Pow er Management Setup Without Saving (Y/N) ?
  • Страница 63 из 97
    English - 59 - 8ip900mk_1001_b.p65 59 BIOS Setup 2003/4/22, 下午 03:55
  • Страница 64 из 97
    English GA-8IP900MK Motherboard 8ip900mk_1001_b.p65 - 60 - 60 2003/4/22, 下午 03:55
  • Страница 65 из 97
    Technical Reference English Chapter 4 @BIOS™ Introduction Gigabyte announces @BIOS™ Windows BIOS live update utility Have you ever updated BIOS by yourself? Or like many other people, you just know what BIOS is, but always hesitate to update it? Because you think updating newest BIOS is unnecessary
  • Страница 66 из 97
    English EasyTune™ 4 Introduction Gigabyte announces EasyTune™ 4 Windows based Overclocking utility EasyTune 4 carries on the heritage so as to pave the way for future generations. Overclock might be one of the most common issues in computer field. But have many users ever tried it? The answer is
  • Страница 67 из 97
    English Flash BIOS Method Introduction Method 1 : Q-Flash A. What is Q-Flash Utility? Q-Flash utility is a pre-O.S. BIOS flash utility enables users to update its BIOS within BIOS mode, no more fooling around any OS. B. How to use Q-Flash? a. After power on the computer, pressing <Del> immediately
  • Страница 68 из 97
    English Load BIOS From Floppy !In the A:drive, insert the "BIOS" diskette, then Press Enter to Run. 1 File(s) xxxx .xxx 256K Total size: 1.39M F5: Refresh Free size: 1.14M DEL: Delete Where xxxx.xxx is name of the BIOS file. ! Press Enter to Run. Are you sure to update BIOS? [Enter] to contiune or
  • Страница 69 из 97
    If you don't have DOS boot disk, we recommend that you used Gigabyte @BIOS™ program to flash BIOS. Press here. 2. Click Start/ All Programs/ GIGABYTE/ @BIOS. 1. Click "@BIOS" item. (1) 3.Click "P". (2) Click here 4. Please select @BIOS sever site, then Click "OK". (3) (4) Methods and steps: I.
  • Страница 70 из 97
    English II. Update BIOS NOT through Internet: a. b. c. d. Do not click "Internet Update" icon Click "Update New BIOS" Please select "All Files" in dialog box while opening the old file. Please search for BIOS unzip file, downloading from internet or any other methods (such as: 8IP900MK.F2). e.
  • Страница 71 из 97
    The installation of Windows 98SE/2K/ME/XP is very simple. Please follow next step to install the function! Stereo Speakers Connection and Settings: We recomm end that you use the speaker with amplifier to acqiire the best sound effect if the stereo output is applied. STEP 1: Connect the stereo
  • Страница 72 из 97
    English 4 Channel Analog Audio Output Mode STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In". Line Out Line In STEP 2 : After installation of the audio driver, you'll find an icon on the taskbar's status area. Click the audio icon "Sound Effect" from the windows tray
  • Страница 73 из 97
    English Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module. STEP 1 : Connect the front channels to "Line Out", the rear channels to "Line In", and the Center/Subwoofer channels to "MIC In". Line In M IC In Line Out STEP 2 :
  • Страница 74 из 97
    English Advanced 6 Channel Analog Audio Output Mode (using Audio Combo Kit, Optional Device): (Audio Combo Kit provides SPDIF output port : optical & coaxis and SURROUND-KIT : Rear R/L & Center/subwoofer) SURROUND-KIT access analog output to rear channels and Center/Subwoofer channels. It is the
  • Страница 75 из 97
    English STEP 3 : Connect the front channels to back audio panel's "Line Out", the rear channels to SURROUND-KIT's REAR R/L, and the Center/Subwoofer channels to SURROUND-KIT's SUB CENTER. STEP 4 : Click the audio icon "Sound Effect" from the windows tray at the bottom of the screen. STEP 5 : Select
  • Страница 76 из 97
    English SPDIF Output Device (Optional Device) A "S/PDIF output" devi ce is available on the motherboard. Cable with rear bracket is provided and could link to the "S/PDIF output" connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting
  • Страница 77 из 97
    Jack-Sensing provides audio connectors error-detection function. Install Microsoft DirectX8.1 before to enable Jack-Sensing support for Windows 98/98SE/2000 /M E. Jack-Sensing includes 2 parts: AUTO and M ANUAL. Following is an example for 2 channels (Windows XP): Introduction of audio connectors
  • Страница 78 из 97
    English If you set wrong with the connectors, the warning message will come out as right picture. Manual setting: If the device picture shows different from what you set, please press "Manual Selection" to set. GA-8IP900MK Motherboard 8ip900mk_1001_t.p65 - 74 - 74 2003/4/22, 下午 03:56
  • Страница 79 из 97
    English - 75 - 8ip900mk_1001_t.p65 75 Technical Reference 2003/4/22, 下午 03:56
  • Страница 80 из 97
    English GA-8IP900MK Motherboard 8ip900mk_1001_t.p65 - 76 - 76 2003/4/22, 下午 03:56
  • Страница 81 из 97
    English Revision History Chapter 5 Appendix Install Drivers Pictures below are shown in Windows XP Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
  • Страница 82 из 97
    English Driver installation finished ! You have to reboot system ! Item Description n Intel Chipset Software Installation Utility Tell the operating system how the chipset components will be configured. n USB Patch for WinXP This patch driver can help you to resolve the USB device wake up S3 hang
  • Страница 83 из 97
    This page reveals the value-added software developed by Gigabyte and its worldwide partners. n Gigabyte Windows Utilities Manager (GWUM) This utility can integrate the Gigabyte's applications in the system tray n Gigabyte Management Tool (GMT) A useful tool which can manage the computer via the
  • Страница 84 из 97
    English SOFTWARE INFORMATION This page list the contects of softwares and drivers in this CD title. HARDWARE INFORMATION This page lists all device you have for this motherboard. CONTACT US Please see the last page for details. GA-8IP900MK Motherboard 8ip900mk_1001_a.p65 - 80 - 80 2003/4/22, 下午
  • Страница 85 из 97
    English EasyTune 4 Utilities Installation Powerful utility that integrates the overclocking and hardware monitoring functions 1. Click "EasyTune4" item. 2. Click "Next". (2) (1) 3. Click "Finish" to restart computer. (4) (3) 4. Right Click the icon to start "EasyTune 4". (6) (5) - 81 -
  • Страница 86 из 97
    English FAQ Below is a collection of general asked questions. To check general asked questions based on a specific motherboard model, please log on to http://tw.giga-byte.com/faq/faq.htm Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why? Answer: Some
  • Страница 87 из 97
    Question 6: Why does system seem unstable after updating BIOS? Answer: Please remember to load Fail-Safe Defaults (Or Load BIOS Defaults) after flashing BIOS. However, if the system instability still remains, please clear CMOS to solve the problem. Question 7: Why do I still get a weak sound after
  • Страница 88 из 97
    English Question 10: Sometimes I hear different continuous beeps from computer after system boots up. What do these beeps usually stand for? Answer: The beep codes below may help you identify the possible computer problems. However, they are only for reference purposes. The situations might differ
  • Страница 89 из 97
    If you encounter any trouble during boot up, please follow the troubleshooting procedures. START Turn off the power and unplug the AC power cable, then remove all of the add-on cards and cables from motherboard. Please make sure motherboard & chassis are not short ? Yes Please isolate the short
  • Страница 90 из 97
    English A Is memory LED on and CPU fan running? No The problem could be caused by power supply, CPU, memory or CPU/memory socket itself. Yes Failure has been excluded. No Check if there is display. Yes Perhaps your VGA card / VGA slot or monitor is defective. Failure has been excluded. Turn off the
  • Страница 91 из 97
    & Customer/Country: Company: Contact Person: Phone No.: E-mail Add. : Model name/Lot Number: BIOS version: Hardware English Technical Support/RMA Sheet PCB revision: O.S./A.S.: Mfs. Model name Size: Driver/Utility: Configuration CPU Memory Brand Video Card Audio Card HDD CD-ROM / DVD-ROM Modem
  • Страница 92 из 97
    English Acronyms Acronyms Meaning ACPI Advanced Configuration and Power Interface APM Advanced Power Management AGP Accelerated Graphics Port AMR Audio Modem Riser ACR Advanced Communications Riser BIOS Basic Input / Output System CPU Central Processing Unit CMOS Complementary Metal Oxide
  • Страница 93 из 97
    Meaning IOAPIC Input Output Advanced Programmable Input Controller ISA Industry Standard Architecture LAN Local Area Network I/O Input / Output LBA Logical Block Addressing LED Light Emitting Diode MHz Megahertz MIDI Musical Instrument Digital Interface MTH Memory Translator Hub MPT Memory Protocol
  • Страница 94 из 97
    English GA-8IP900MK Motherboard 8ip900mk_1001_a.p65 - 90 - 90 2003/4/22, 下午 03:57
  • Страница 95 из 97
    English - 91 - 8ip900mk_1001_a.p65 91 Memo 2003/4/22, 下午 03:57
  • Страница 96 из 97
    English CONTACT US Contact us via the information in this page all over the world. — Taiwan — The Netherlands Gigabyte Technology Co., Ltd. Giga-Byte Technology B.V. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, R.O.C. Address: Postbus 1385, 5602 BJ, Eindhoven, The Netherlands
  • Страница 97 из 97