Инструкция для GIGABYTE GA-8VM800PMD-775-RH

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

GA-8VM800PMD-775-RH

Intel

®

 Pentium

® 

4 LGA775 Processor Motherboard

User's Manual

Rev. 1001
12ME-VM800PMTR-1001R

* The WEEE marking on the product indicates this product must not be disposed of with user's other household waste

and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
Оглавление инструкции
  • Страница 1 из 89
    GA-8VM800PMD-775-RH Intel® Pentium® 4 LGA775 Processor Motherboard User's Manual Rev. 1001 12ME-VM800PMTR-1001R * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the
  • Страница 2 из 89
    Motherboard GA-8VM800PMD-775-RH Jul. 7, 2006 Motherboard GA-8VM800PMD-775-RH Jul. 7, 2006
  • Страница 3 из 89
    Copyright © 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. No part of this manual may be reproduced, copied,
  • Страница 4 из 89
    Table of Contents Item Checklist ................................................................................................................. 6 Optional Accessories ...................................................................................................... 6 GA-8VM800PMD-775-RH
  • Страница 5 из 89
    Chapter 3 Drivers Installation ...................................................................................... 47 3-1 3-2 Install Chipset Drivers .................................................................................... 47 Software Application
  • Страница 6 из 89
    Item Checklist IDE Cable x 1, FDD Cable x 1 SATA Cable x 1 I/O Shield * The items listed above are for reference only, and are subject to change without notice. Optional Accessories 2 Ports USB2.0 Cable (Part Number: 12CR1-1UB030-51/R) COM Port Cable (Part Number: 12CF1-1CM001-31/R) -6-
  • Страница 7 из 89
    GA-8VM800PMD-775-RH Motherboard Layout DDRII_1 FDD GA-8VM800PMD-775-RH VGA LPT COMA LGA775 DDRII_2 CPU_FAN KB_MS Winbond W83627 USB LAN USB ATX_12V AUDIO F_AUDIO VIA P4M800 Pro BIOS ATX AGP IDE1 IDE2 SYS _FAN PCI1 RTL 8100C SATA1 VIA VT8237R+ PCI2 CD_IN CLR_CMOS PCI3 COMB CI AUX_IN SUR_CEN SPDIF_IO
  • Страница 8 из 89
    Block Diagram LGA 775 Processor AGP 4X/8X System Bus 533/800MHz VGA Port AGP CLK (66MHz) CPUCLK+/- (133/200MHz) 400/533MHz DDR II RJ45 3 PCI RTL8100C 66MHz V_Link VIA P4M800 Pro 2 Serial ATA VIA VT8237R+ BIOS LPC BUS AC97 Link Winbond W83627 Floppy LPT Port PS/2 KB/Mouse 8 USB Ports ATA33/66/
  • Страница 9 из 89
    1-1 English Chapter 1 Hardware Installation Considerations Prior to Installation Preparing Your Computer The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow
  • Страница 10 из 89
    English 1-2 Feature Summary CPU Front Side Bus Chipset LAN Audio Storage O.S Support Memory Expanstion Slots Internal Connectors Supports LGA775 Intel® Pentium ® 4 Processor L2 cache varies with CPU Supports 800/533MHz FSB Northbridge: VIA P4M800 Pro Chipset Southbridge: VIA 8237R+ Onboard Realtek
  • Страница 11 из 89
    I/O Control Hardware Monitor BIOS Additional Features Bundle Software Form Factor 1 PS/2 keyboard port 1 PS/2 mouse port 1 parallel port 1 serial port (COMA) 1 VGA port 4 USB 2.0/1.1 ports 1 RJ-45 port 3 audio jacks (Line In / Line Out / MIC In) Winbond W83627 chip System voltage detection CPU /
  • Страница 12 из 89
    English 1-3 Installation of the CPU and CPU Cooler Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU
  • Страница 13 из 89
    Male Push Pin The top of Female Push Pin Female Push Pin Fig.1 Please apply an even layer of CPU cooler paste on the surface of the installed CPU. Fig. 2 (Turning the push pin along the direction of arrow is to remove the CPU cooler, on the contrary, is to install.) Please note the direction of
  • Страница 14 из 89
    English 1-4 Installation of Memory Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing
  • Страница 15 из 89
    Installation of Expansion Cards You can install your expansion card by following the steps outlined below: 1. Read the related expansion card's instruction document before installing the expansion card into the computer. 2. Remove your computer's chassis cover, screws and slot bracket from the
  • Страница 16 из 89
    English 1-6 I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse Connector To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple). Parallel Port The parallel port allows connection of a printer, scanner and other
  • Страница 17 из 89
    Connectors Introduction 3 English 1-7 2 5 1 6 10 4 7 19 9 8 11 12 14 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) ATX_12V ATX (Power Connector) CPU_FAN SYS_FAN FDD IDE1 / IDE2 SATA0 / SATA1 F_PANEL PWR_LED F_AUDIO 13 16 17 18 11) 12) 13) 14) 15) 16) 17) 18) 19) - 17 - 15 CD_IN AUX_IN SPDIF_IO SUR_CEN F_USB1 /
  • Страница 18 из 89
    English 1/2) ATX_12V / ATX (Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power
  • Страница 19 из 89
    The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power
  • Страница 20 из 89
    English 6) IDE1 / IDE2 (IDE Connector) An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the
  • Страница 21 из 89
    F_PANEL (Front Panel Connector) Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignments below. Speaker Connector Message LED/ Power/ Sleep LED SPEAK- SPEAK+ MSG+ MSGPW+ PW- Power Switch 2 1
  • Страница 22 из 89
    English 9) PWR_LED The PWR_LED connector is connected with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. Pin No. 1 1 2 3 Definition MPD+ MPDMPD- 10) F_AUDIO (Front Audio Panel Connector) Please make sure the pin assignment on
  • Страница 23 из 89
    English 11) CD_IN (CD IN Connector, black) Connect CD-ROM or DVD-ROM audio out to the connector. Pin No. 1 Definition CD-L 2 3 GND GND 4 1 CD-R 12) AUX_IN (AUX In Connector, white) Connect other device (such as PCI TV Tunner audio out) to the connector. Pin No. 1 1 Definition AUX-L GND GND 4 - 23 -
  • Страница 24 из 89
    English 13) SPDIF_IO (SPDIF In/ Out connector, red) The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Use SPDIF IN feature only when your
  • Страница 25 из 89
    Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local
  • Страница 26 из 89
    English 17) CI (Chassis Intrusion, Case Open) This 2-pin connector allows your system to detect if the chassis cover is removed. You can check the "Case Opened" status in BIOS Setup. Pin No. 1 1 2 Definition GND Signal 18) CLR_CMOS (Clear CMOS) You may clear the CMOS data to its default values by
  • Страница 27 из 89
    English 19) BATTERY Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. If you want to erase CMOS... 1. Turn off the computer and unplug the
  • Страница 28 из 89
    English GA-8VM800PMD-775-RH Motherboard - 28 -
  • Страница 29 из 89
    BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard
  • Страница 30 из 89
    English The Main Menu (For example: BIOS Ver. : F4a) Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. CMOS Setup Utility-Copyright (C) 1984-2006 Award
  • Страница 31 из 89
    Optimized Defaults indicates the value of the system parameters which the system would be in best performance configuration. Set Supervisor Password Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup. Set User Password Change, set, or disable
  • Страница 32 из 89
    English 2-1 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Wed, Jun 14 2006 10:40:9 IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave IDE Channel 2 Master IDE Channel 3 Master
  • Страница 33 из 89
    Drive A The category identifies the types of floppy disk drive A that has been installed in the computer. None No floppy drive installed 360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity. 1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is
  • Страница 34 из 89
    English 2-2 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Advanced BIOS Features Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check CPU Hyper-Threading (Note) Limit CPUID Max. to 3 (Note) No-Execute Memory Protect (Note)
  • Страница 35 из 89
    Enabled Disabled Enables CPU Hyper Threading Feature. Please note that this feature is only working for operating system with multi processors mode supported. (Default value) Disables CPU Hyper Threading. Limit CPUID Max. to 3 (Note) Enabled Disabled Limit CPUID Maximum value to 3 when use older OS
  • Страница 36 из 89
    English 2-3 Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Integrated Peripherals OnChip IDE Channel 0 OnChip IDE Channel 1 OnChip Serial ATA SATA Mode AC97 Audio USB 1.1 Controller USB 2.0 Controller USB Keyboard Support USB Mouse Support Onboard H/W LAN OnBoard
  • Страница 37 из 89
    Enabled Disabled English USB Mouse Support Enable USB mouse support. Disable USB mouse support. (Default value) Onboard H/W LAN Enabled Disabled Enable onboard LAN chip function. (Default value) Disable onboard LAN chip function. OnBoard LAN Boot ROM This function decide whether to invoke the boot
  • Страница 38 из 89
    English 2-4 Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Power Management Setup ACPI Suspend Type x USB Device Wake-Up From S3 Soft-Off by PWRBTN AC BACK Function Keyboard Power On Mouse Power On PME Event Wake Up Modem Ring Resume Resume by Alarm x Date (of
  • Страница 39 из 89
    Disabled Enabled English Mouse Power On Disable this function. (Default value) Double click on PS/2 mouse left button to power on the system. PME Event Wake Up This feature requires an ATX power supply that provides at least 1A on the 5VSB lead. Disabled Disable this function. Enabled Enable PME as
  • Страница 40 из 89
    English 2-5 PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2006 Award Software PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment PCI 3 IRQ Assignment : Move Enter: Select F5: Previous Values [Auto] [Auto] [Auto] +/-/PU/PD: Value F6: Fail-Safe Defaults Item Help Menu
  • Страница 41 из 89
    PC Health Status CMOS Setup Utility-Copyright (C) 1984-2006 Award Software PC Health Status Reset Case Open Status Case Opened VCORE DDR18V +3.3V +12V System Temperature CPU Temperature Current SYS FAN Speed Current CPU FAN Speed SYS FAN Fail Warning CPU FAN Fail Warning CPU Smart FAN Control
  • Страница 42 из 89
    English 2-7 Frequency / Voltage Control CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Frequency/Voltage Control CPU Clock Ratio (Note) Auto Detect PCI Clk Spread Spectrum DRAM Clock [22X] [Enabled] [Enabled] [By SPD] : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F6:
  • Страница 43 из 89
    Load Fail-Safe Defaults English 2-8 CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults
  • Страница 44 из 89
    English 2-10 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations Enter Password: PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults
  • Страница 45 из 89
    English 2-11 Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set
  • Страница 46 из 89
    English GA-8VM800PMD-775-RH Motherboard - 46 -
  • Страница 47 из 89
    Pictures below are shown in Windows XP. Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the Setup.exe. 3-1 Install
  • Страница 48 из 89
    English 3-2 Software Application This page displays all the tools that Gigabyte developed and some free software. You can click an item to install it. 3-3 Software Information This page lists the contents of software and drivers in this CD-title. GA-8VM800PMD-775-RH Motherboard - 48 -
  • Страница 49 из 89
    Hardware Information English 3-4 This page lists all device you have for this motherboard. 3-5 Contact Us Please see the last page for details. - 49 - Drivers Installation
  • Страница 50 из 89
    English GA-8VM800PMD-775-RH Motherboard - 50 -
  • Страница 51 из 89
    4-1 English Chapter 4 Appendix Unique Software Utilities (Not all model support these Unique Software Utilities, please check your MB features.) 4-1-1 EasyTune 5 Introduction EasyTune 5 presents the most convenient Windows based system performance enhancement and manageability utility. Featuring
  • Страница 52 из 89
    English 4-1-2 Xpress Recovery Introduction Xpress Recovery2 is designed to provide quick backup and restoration of hard disk data. Supporting Microsoft operating systems including Windows XP/2000/NT/98/Me and DOS, and file systems including FAT16, FAT32, and NTFS, Xpress Recovery2 is able to back
  • Страница 53 из 89
    1. RESTORE: Restore the backed-up data to your hard disk. (This button will not appear if there is no backup file.) 2. BACKUP: Back up data from hard disk. 3. REMOVE: Remove previously-created backup files to release disk space. (This button will not appear if there is no backup file.) 4. REBOOT:
  • Страница 54 из 89
    English 4-1-3 Flash BIOS Method Introduction Method 1 : Q-FlashTM Utility Q-FlashTM is a BIOS flash utility embedded in Flash ROM. With this utility, users only have to stay in the BIOS menu when they want to update BIOS. Q-Flash TM allows users to flash BIOS without any utility in TM DOS or
  • Страница 55 из 89
    English Entering the Q-FlashTM utility: Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu. CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI
  • Страница 56 из 89
    English Using the Q-FlashTM utility: This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin" section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your computer. If you have already put the floppy
  • Страница 57 из 89
    English 3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be displayed. Please do not take out the floppy disk when it begins flashing BIOS. 4. Press any keys to return to the Q-Flash menu when the BIOS
  • Страница 58 из 89
    English 6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to Load Optimized Defaults item and press Enter to load BIOS Optimized Defaults. Normally the system redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the BIOS
  • Страница 59 из 89
    The Q-FlashBIOS utility screen consists of the following key components. Q-FlashTM utility bar Q-Flash Utility V1.30 Flash Type/Size.................................SST 49LF003A Task menu for Q-FlashTM utility Enter : Run Keep DMI Data Enable Update BIOS from Floppy Save BIOS to Floppy :Move
  • Страница 60 из 89
    English 3. Press Y button on your keyboard after you are sure to update BIOS. Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time. Q-Flash Utility V1.30 Flash Type/Size.................................SST 49LF003A 256K Keep DMI Data BIOS Now Updating
  • Страница 61 из 89
    If you do not have a DOS startup disk, we recommend that you use the new @BIOS utility. @BIOS allows users to update their BIOS under Windows. Just select the desired @BIOS server to download the latest version of BIOS. Fig 1. Installing the @BIOS utility Fig 2. Installation Complete and Run @BIOS
  • Страница 62 из 89
    English III. Save BIOS In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to save the current BIOS version. IV. Check out supported motherboard and Flash ROM: In the very beginning, there is "About this program" icon shown in dialog box. It can help you check out
  • Страница 63 из 89
    English 4-1-4 Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3) Configure RAID set in RAID BIOS.(Note) (4) Make a floppy disk containing the
  • Страница 64 из 89
    English (2) Configuring SATA controller mode and boot sequence in BIOS Setup You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and set BIOS boot sequence for the SATA hard drive(s). Step 1: Turn on your computer and press Del to enter BIOS Setup during
  • Страница 65 из 89
    CMOS Setup Utility-Copyright (C) 1984-2006 Award Software Advanced BIOS Features Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check CPU Hyper-Threading Limit CPUID Max. to 3 No-Execute Memory Protect CPU Enhanced Halt (C1E) CPU Thermal Monitor 2(TM2) CPU
  • Страница 66 из 89
    English (3) Configuring RAID set in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed to Section 4 if you do not want to create RAID. Step 1: After the POST memory test begins and before the operating system boot begins, the following information will
  • Страница 67 из 89
    VIA Tech. VT8237 SATA RAID BIOS Ver 2.31 Create a RAID array with the hard disks attached to VIA RAID controller Auto Setup For Performance Array Mode RAID 0 (Striping) Select Disk Drives Block Size 64K Start Create Process Channel Drive Name F1 , Enter ESC : : : : Array Name View Array/disk Status
  • Страница 68 из 89
    English After selecting a RAID mode, you must decide whether you want the RAID array to be configured automatically or manually. Auto Setup allows BIOS to assign the hard drives and create arrays automatically, but it does not duplicate the mirroring drives even if user selects Create and duplicate
  • Страница 69 из 89
    VIA Tech. VT8237 SATA RAID BIOS Ver 2.31 Create Array Delete Array Create/Delete Spare Select Boot Array Serial Number View Delete a RAID array contain the hard disks attached to VIA RAID controller F1 , Enter ESC The selected array will be destoried. Are you sure? Continue? Press Y/N Channel Drive
  • Страница 70 из 89
    English D. Serial Number View: Highlight Serial Number View and press ENTER. Use the ARROW keys to select a drive, and the selected drive's serial number can be viewed in the last line. The serial number is assigned by the disk drive manufacturer (Figure 11). VIA Tech. VT8237 SATA RAID BIOS Ver
  • Страница 71 из 89
    Step 1: Insert the prepared startup disk and motherboard driver CD-ROM in your system. Boot from the startup disk. Once at the A:\> prompt, change to the CD-ROM drive (example: D:\>). At the D:\> prompt, type the following two commands. Press ENTER after each command (Figure 13): cd bootdrv menu
  • Страница 72 из 89
    English (5) Installing SATA controller driver during OS installation Now that you have prepared the SATA driver disk and configured BIOS settings, you are ready to install Windows 2000/XP onto your SATA hard drive with the SATA driver. The following is an example of Windows XP installation. Step 1:
  • Страница 73 из 89
    Windows Setup You have chosen to configure a SCSI Adapter for use with Windows, using a device support disk provided by an adapter manufacturer. Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen. VIA VT8237/6421/6410 SATA RAID Controller(Windows
  • Страница 74 из 89
    English After the SATA controller driver installation is completed, you should see a screen as below. It indicates that you have installed the SATA controller driver successfully. You can proceed with the Windows 2000/XP installation. WindowsXP Professional Setup Welcome to Setup. This port of the
  • Страница 75 из 89
    2 Channel Audio Setup We recommend that you use speakers with amplifier to get the best sound effect if the stereo output is applied. STEP 1: Connect the stereo speakers or earphone to "Line Out." Line Out STEP 2: After installing the audio driver, you'll find a Sound Effect icon on the lower right
  • Страница 76 из 89
    English 4 Channel Analog Audio Output Mode STEP 1: Connect the front channels to "Line Out," the rear channels to "Line In." Line Out Line In STEP 2: After installing the audio driver, you'll find a Sound Effect icon on the lower right hand taskbar. Click the icon to select the function. STEP 3: On
  • Страница 77 из 89
    English Basic 6 Channel Analog Audio Output Mode Use the back audio panel to connect the audio output without any additional module. STEP 1: Connect the front channels to "Line Out",the rear channels to "Line In", and the Center/Subwoofer channels to "MIC In". Line In MIC In Line Out STEP 2: After
  • Страница 78 из 89
    English Advanced 6 Channel Analog Audio Output Mode (using Audio Combo Kit, Optional Device): Audio Combo Kit provides SPDIF output port (optical & coaxial) and SURROUND-Kit (Rear R/L & CEN /Subwoofer) SURROUND-Kit access analog output to rear channels and Center/Subwoofer channels. It is the best
  • Страница 79 из 89
    English STEP 3: Connect the front channels to back audio panel's "Line Out", the rear channels to SURROUND-Kit's REAR R/L, and the Center/Subwoofer channels to SURROUND-Kit's SUB CENTER. STEP 4: After installing the audio driver, you'll find a Sound Effect icon on the lower right hand taskbar.
  • Страница 80 из 89
    English SPDIF Output Device (Optional Device) A "SPDIF output" connector is available on the motherboard. Cable with rear bracket could link to the "SPDIF output" connector (As picture.) For the further linkage to decoder, rear bracket provides coaxial cable and Fiber connecting port. STEP 1:
  • Страница 81 из 89
    Troubleshooting Below is a collection of general asked questions. To check general asked questions based on a specific motherboard model, please log on to GIGABYTE's website. Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why? Answer: Some advanced
  • Страница 82 из 89
    English GA-8VM800PMD-775-RH Motherboard - 82 -
  • Страница 83 из 89
    English - 83 - Appendix
  • Страница 84 из 89
    English GA-8VM800PMD-775-RH Motherboard - 84 -
  • Страница 85 из 89
    English - 85 - Appendix
  • Страница 86 из 89
    English GA-8VM800PMD-775-RH Motherboard - 86 -
  • Страница 87 из 89
    English Contact Us Taiwan (Headquarters) GIGA-BYTE TECHNOLOGY CO., LTD. China NINGBO G.B.T. TECH. TRADING CO., LTD. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei 231, Taiwan WEB address : http://www.gigabyte.cn Shanghai TEL: +886-2-8912-4888 FAX: +886-2-8912-4003 TEL: +86-21-63410999 FAX:
  • Страница 88 из 89
    English Germany Russia G.B.T. TECHNOLOGY TRADING GMBH WEB address : http://www.gigabyte.de Moscow Representative Office Of GIGA-BYTE Technology Co., Ltd. U.K. G.B.T. TECH. CO., LTD. WEB address : http://www.gigabyte.ru Latvia WEB address : http://www.giga-byte.co.uk The Netherlands GIGA-BYTE Latvia
  • Страница 89 из 89