Инструкция для GIGABYTE GA-M68M-S2 (REV.1)

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image


AM2+/AM2 socket motherboard for
AMD Phenom

 II processor/ AMD Phenom


AMD Athlon

 II processor/ AMD Athlon


AMD Sempron


User's Manual

Rev. 1001

Оглавление инструкции
  • Страница 1 из 97
    GA-M68M-S2 AM2+/AM2 socket motherboard for AMD Phenom™ II processor/ AMD Phenom™ processor/ AMD Athlon™ II processor/ AMD Athlon™ processor/ AMD Sempron™ processor User's Manual Rev. 1001 12ME-M68MS2-1001R
  • Страница 2 из 97
    Motherboard GA-M68M-S2 Aug. 14, 2009 GA-M68M-S2 Motherboard Aug. 14, 2009
  • Страница 3 из 97
    Copyright © 2009 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and
  • Страница 4 из 97
    Table of Contents Box Contents ................................................................................................................. 6 Optional Items ................................................................................................................. 6 GA-M68M-S2
  • Страница 5 из 97
    Chapter 3 Drivers Installation ...................................................................................... 53 3-1 3-2 Installing Chipset Drivers ............................................................................... 53 Application Software
  • Страница 6 из 97
    Box Contents GA-M68M-S2 motherboard Motherboard driver disk User's Manual One IDE cable One SATA 3Gb/s cables I/O Shield • The box contents above are for reference only and the actual items shall depend on product package you obtain. The box contents are subject to change without notice. • The
  • Страница 7 из 97
  • Страница 8 из 97
    Block Diagram PCIe CLK (100 MHz) CPU CLK+/-(200 MHz) AM3/AM2+/AM2 CPU DDR2 1066/800/667 MHz DIMM Dual Channel Memory 1 PCI Express x16 Hyper Transport Bus PCI Express x16 D-Sub PCI Express Bus 8 USB Ports x1 NVIDIA® GeForce 7025/ nForce 630a PCIe CLK (100 MHz) 2 SATA 3Gb/s 1 PCI Express x1 LAN RJ45
  • Страница 9 из 97
    Chapter 1 Hardware Installation 1-1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures: •
  • Страница 10 из 97
    1-2 Product Specifications CPU  Hyper Transport Bus  Chipset  Memory    Audio LAN Expansion Slots Storage Interface            USB   Internal Connectors              Hardware Installation Support for AM3/AM2+/AM2 processors: AMD Phenom ™ II processor/ AMD Phenom ™
  • Страница 11 из 97
    Internal Connectors Back Panel Connectors I/O Controller Hardware Monitor BIOS Unique Features Bundled Software Operating System Form Factor                                1 x chassis intrusion header 1 x power LED header 1 x PS/2 keyboard port 1 x PS/2 mouse port 1 x
  • Страница 12 из 97
    1-3 Installing the CPU and CPU Cooler Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.) • Always turn off the computer and unplug the power cord from the power outlet
  • Страница 13 из 97
    B. Follow the steps below to correctly install the CPU into the motherboard CPU socket. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. CPU Socket Locking Lever Step 1: Completely lift up the CPU socket
  • Страница 14 из 97
    1-3-2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.) Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU. Step 2: Place the CPU cooler on the
  • Страница 15 из 97
    1-4 Installing the Memory Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest memory support list.) •
  • Страница 16 из 97
    1-4-2 Installing a Memory Before installing a memory module , make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR2 DIMMs are not compatible to DDR DIMMs. Be sure to install DDR2 DIMMs on this motherboard. Notch DDR2 DIMM A
  • Страница 17 из 97
    1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. • Always turn off the computer and unplug the power cord from the
  • Страница 18 из 97
    1-6 Back Panel Connectors PS/2 Keyboard and PS/2 Mouse Port Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard. Parallel Port Use the parallel port to connect devices such as a printer, scanner and etc. The parallel port is also called a
  • Страница 19 из 97
    Line In Jack (Blue) The default line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc. Line Out Jack (Green) The default line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a
  • Страница 20 из 97
    1-7 Internal Connectors 1 2 3 6 16 11 12 17 7 9 15 13 14 1) 2) 3) 4) 5) 6) 7) 8) 9) ATX_12V ATX CPU_FAN SYS_FAN FDD IDE SATA2_0 / SATA2_1 PWR_LED BAT 5 4 10) 11) 12) 13) 14) 15) 16) 17) 8 10 F_PANEL F_AUDIO HDA_SUR CD_IN SPDIF_IO F_USB1 / F_USB2 CI CLR_CMOS Read the following guidelines before
  • Страница 21 из 97
    1/2) ATX_12V/ATX (2x2 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all
  • Страница 22 из 97
    3/4) CPU_FAN/SYS_FAN (Fan Headers) The motherboard has a 4-pin CPU fan header (CPU_FAN) and a 3-pin system fan header (SYS_FAN). Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the
  • Страница 23 из 97
    6) IDE (IDE Connector) The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attaching the IDE cable, locate the foolproof groove on the connector. If you wish to connect two IDE devices, remember to set the jumpers and the cabling according to the role of
  • Страница 24 из 97
    8) PWR_LED (System Power LED Header) This header can be used to connect a system power LED on the chassis to indicate system power status. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state
  • Страница 25 из 97
    10) F_PANEL (Front Panel Header) Connect the power switch, reset switch, speaker and system status indicator on the chassis front panel to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. 2 1 SPEAK- Speaker SPEAK+ Power Switch
  • Страница 26 из 97
    11) F_AUDIO (Front Panel Audio Header) The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. You may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module connector match the pin assignments of the motherboard
  • Страница 27 из 97
    13) CD_IN (CD In Connector) You may connect the audio cable that came with your optical drive to the header. Pin No. Definition 1 GND 3 4 1 CD-L 2 GND CD-R 14) SPDIF_IO (S/PDIF Out Header) This header supports digital S/PDIF out. Via an optional S/PDIF out cable, this header can connect to an audio
  • Страница 28 из 97
    15) F_USB1/F_USB2 (USB Headers) The headers conform to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer. Pin No. 9 USB DX- 4 USB DY- 5 6 USB DX+ USB DY+ GND GND 9 10 1 3 8 10
  • Страница 29 из 97
    17) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a
  • Страница 30 из 97
    Hardware Installation - 30 -
  • Страница 31 из 97
    Chapter 2 BIOS Setup BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a
  • Страница 32 из 97
    2-1 Startup Screen The following screen may appear when the computer boots. Award Modular BIOS v6.00PG, An Energy Star Ally Copyright (C) 1984-2009, Award Software, Inc. Motherboard Model BIOS Version GA-M68M-S2 F1a . . . . <DEL>: BIOS Setup <F9>: XpressRecovery2 <F12>: Boot Menu <End>: Qflash
  • Страница 33 из 97
    2-2 The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter a sub-menu. (Sample BIOS Version: F1a) CMOS Setup Utility-Copyright (C) 1984-2009 Award Software   MB
  • Страница 34 из 97
     MB Intelligent Tweaker(M.I.T.) Use this menu to configure the clock, frequency and voltages of your CPU, memory, etc.  Standard CMOS Features Use this menu to configure the system time and date, hard drive types, floppy disk drive types, and the type of errors that stop the system boot, etc. 
  • Страница 35 из 97
    2-3 MB Intelligent Tweaker(M.I.T.) CMOS Setup Utility-Copyright (C) 1984-2009 Award Software MB Intelligent Tweaker(M.I.T.) Set Memory Clock x Memory Clock  DRAM Configuration : Move Enter: Select F5: Previous Values [Auto] x2.66 533MHz [Press Enter] +/-/PU/PD: Value F6: Fail-Safe Defaults
  • Страница 36 из 97
    DRAM Configuration CMOS Setup Utility-Copyright (C) 1984-2009 Award Software DRAM Configuration x x x x x x x x x x x x x x DCTs Mode (Note) DDRII Timing Items CAS# latency RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time 1T/2T Command Timing TwTr Command Delay Trfc0 for DIMM1 Trfc2
  • Страница 37 из 97
    Trfc1 for DIMM3 Options are: 75ns, 105ns, 127.5ns, 195ns, 327.5ns. Trfc3 for DIMM4 Options are: 75ns, 105ns, 127.5ns, 195ns, 327.5ns. Write Recovery Time Options are: Auto (default), 3T~6T. Precharge Time Options are: Auto (default), 2T, 3T. Row Cycle Time Options are: Auto (default), 11T~26T. RAS
  • Страница 38 из 97
    2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 2 Master IDE Channel 3 Master [None] [None] [None] [None] Drive A Floppy 3 Mode Support [1.44M, 3.5"]
  • Страница 39 из 97
    The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Cylinder Head Precomp Landing Zone Sector Number of cylinders. Number of heads.
  • Страница 40 из 97
    2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Advanced BIOS Features Virtualization Patch AMD TLB Erratum (Note) AMD K8 Cool&Quiet control  Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check HDD S.M.A.R.T. Capability
  • Страница 41 из 97
    Password Check Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup. After configuring this item, set the password(s) under the Set Supervisor/User Password item in the BIOS Main Menu. Setup A password is only required for entering the BIOS Setup
  • Страница 42 из 97
    2-6 Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Integrated Peripherals On-Chip IDE Channel NV SATA Controller IDE Prefetch Mode USB Memory Type  Serial-ATA RAID Config Onboard Audio Function On-Chip MAC Lan Onboard LAN Boot ROM Onboard Serial Port 1 Onboard
  • Страница 43 из 97
    NV SATA RAID function Enables or disables RAID for the integrated SATA 3Gb/s controller. Enabled allows you to configure RAID for individual SATA channel. (Default: Disabled) NV SATA 1 Primary RAID Enables or disables RAID for the first channel of the integrated SATA 3Gb/s controller. This item is
  • Страница 44 из 97
    USB Keyboard Support Allows USB keyboard to be used in MS-DOS. (Default: Disabled) USB Mouse Support Allows USB mouse to be used in MS-DOS. (Default: Disabled) Legacy USB storage detect Determines whether to detect USB storage devices, including USB flash drives and USB hard drives during the POST.
  • Страница 45 из 97
    2-7 Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2009 Award Software Power Management Setup ACPI Suspend Type Soft-Off by Power button PME Event Wake Up Modem Ring On USB Resume from Suspend Power-On by Alarm x Day of Month Alarm x Time (hh:mm:ss) Alarm HPET Support (Note) HPET Mode
  • Страница 46 из 97
    USB Resume from Suspend Allows the system to be awakened from ACPI S3 sleep state by a wake-up signal from the installed USB device. (Default: Enabled) Power-On by Alarm Determines whether to power on the system at a desired time. (Default: Disabled) If enabled, set the date and time as following:
  • Страница 47 из 97
    2-8 PnP/PCI Configurations CMOS Setup Utility-Copyright (C) 1984-2009 Award Software PnP/PCI Configurations PCI 1 IRQ Assignment PCI 2 IRQ Assignment : Move Enter: Select F5: Previous Values [Auto] [Auto] +/-/PU/PD: Value F6: Fail-Safe Defaults Item Help Menu Level F10: Save ESC: Exit F1:
  • Страница 48 из 97
    2-9 PC Health Status CMOS Setup Utility-Copyright (C) 1984-2009 Award Software PC Health Status Reset Case Open Status Case Opened Vcore DDR2 1.8V +3.3V +12V Current System Temperature Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed System Warning Temperature CPU Warning
  • Страница 49 из 97
    CPU Smart FAN Mode Specifies how to control CPU fan speed. This item is configurable only if CPU Smart FAN Control is set to Enabled. Auto Lets BIOS autodetect the type of CPU fan installed and sets the optimal CPU fan control mode. (Default) Voltage Sets Voltage mode for a 3-pin CPU fan. PWM Sets
  • Страница 50 из 97
    2-10 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2009 Award Software   MB Intelligent Tweaker(M.I.T.) Standard CMOS Features   Advanced BIOS Features Integrated Peripherals   Power Management Setup PnP/PCI Configurations  PC Health Status Load Fail-Safe Defaults Load
  • Страница 51 из 97
    2-12 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2009 Award Software   MB Intelligent Tweaker(M.I.T.) Standard CMOS Features Load Fail-Safe Defaults Load Optimized Defaults   Advanced BIOS Features Integrated Peripherals Enter Power Management Setup Password: Set
  • Страница 52 из 97
    2-13 Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2009 Award Software  MB Intelligent Tweaker(M.I.T.)   Standard CMOS Features Advanced BIOS Features   Integrated Peripherals Power Management Setup   PnP/PCI Configurations PC Health Status Load Fail-Safe Defaults Load Optimized
  • Страница 53 из 97
    Chapter 3 Drivers Installation • Before installing the drivers, first install the operating system. • After installing the operating system, insert the motherboard driver disk into your optical drive. The driver Autorun screen is automatically displayed which looks like that shown in the screen
  • Страница 54 из 97
    3-2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software. You can click the Install button on the right of an item to install it. 3-3 Technical Manuals This page provides content descriptions for this driver disk and the
  • Страница 55 из 97
    3-4 Contact For the detailed contact information of the GIGABYTE Taiwan headquarter or worldwide branch offices, click the URL on this page to link to the GIGABYTE Website. 3-5 System This page provides the basic system information. - 55 - Drivers Installation
  • Страница 56 из 97
    3-6 Download Center To update the BIOS, drivers, or applications, click the Download Center button to link to the GIGABYTE Web site. The latest version of the BIOS, drivers, or applications will be displayed. Drivers Installation - 56 -
  • Страница 57 из 97
    Chapter 4 Unique Features 4-1 Xpress Recovery2 Xpress Recovery2 is a utility that allows you to quickly compress and back up your system data and perform restoration of it. Supporting NTFS, FAT32, and FAT16 file systems, Xpress Recovery2 can back up data on PATA and SATA hard drives and restore it.
  • Страница 58 из 97
    Step 3: When partitioning your hard drive, make sure to leave unallocated space (10 GB or more is recommended; actual size requirements vary, depending on the amount of data) and begin the installation of the operating system. Step 4: After the operating system is installed, rightclick the Computer
  • Страница 59 из 97
    D. Using the Restore Function in Xpress Recovery2 Select RESTORE to restore the backup to your hard drive in case the system breaks down. The RESTORE option will not be present if no backup is created before. E. Removing the Backup Step 1: If you wish to remove the backup file, select REMOVE. Step
  • Страница 60 из 97
    4-2 BIOS Update Utilities GIGABYTE motherboards provide two unique BIOS update tools, Q-FlashTM and @BIOS TM. GIGABYTE Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MSDOS mode. Additionally, this motherboard features the DualBIOS TM design, which
  • Страница 61 из 97
    B. Updating the BIOS When updating the BIOS, choose the location where the BIOS file is saved. The follow procedure assumes that you save the BIOS file to a floppy disk. Step 1: 1. Insert the floppy disk containing the BIOS file into the floppy disk drive. In the main menu of Q-Flash, use the up or
  • Страница 62 из 97
    Step 4: Press <Esc> and then <Enter> to exit Q-Flash and reboot the system. As the system boots, you should see the new BIOS version is present on the POST screen. Step 5: During the POST, press <Delete> to enter BIOS Setup. Select Load Optimized Defaults and press <Enter> to load BIOS defaults.
  • Страница 63 из 97
    4-2-2 Updating the BIOS with the @BIOS Utility A. Before You Begin: 1. 2. 3. 4. In Windows, close all applications and TSR (Terminate and Stay Resident) programs. This helps prevent unexpected failures when performing a BIOS update. During the BIOS update process, ensure the Internet connection is
  • Страница 64 из 97
    4-3 EasyTune 6 GIGABYTE's EasyTune 6 is a simple and easy-to-use interface that allows users to fine-tune their system settings or do overclock/overvoltage in Windows environment. The user-friendly EasyTune 6 interface also includes tabbed pages for CPU and memory information, lettings users read
  • Страница 65 из 97
    Chapter 5 Appendix 5-1 Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: A. B. C. D. E. Install SATA hard drive(s) in your computer. Configure SATA controller mode in BIOS Setup. Configure a RAID array in RAID BIOS. (Note) Make a floppy disk containing the SATA
  • Страница 66 из 97
    B. Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup . Step 1: Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Under Integrated Peripherals, ensure NV SATA Controller is
  • Страница 67 из 97
    C. Configuring RAID set in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array. For a non-RAID configuration, please skip this step and proceed to the installation of Windows operating system. Step 1: After the POST memory test begins and before the operating system boot begins,
  • Страница 68 из 97
    Step 5: Next, select the hard drives which you wish to be included in the disk array. The Free Disks block displays the information about the SATA hard drives that are available for use as RAID array drives. Press <Tab> to move to the Free Disks block. Select the target hard drives using the up or
  • Страница 69 из 97
    After that, the Array List screen appears, displaying the RAID array that you have created (Figure 7). MediaShield Utility Nov 20 2006 - Array List Boot Status Vendor Array Model Name No Healthy NVIDIA STRIPE 223.57G [Ctrl-X] Exit [ Select ]  [B] Set Boot [N] New Array [ENTER] Detail Figure 7
  • Страница 70 из 97
    5-1-2 Making a SATA RAID/AHCI Driver Diskette for Windows XP (Required for AHCI and RAID Mode) To successfully install operating system onto SATA hard drive(s) that is/are configured to RAID/AHCI mode, you need to install the SATA controller driver during the OS installation. Without the driver,
  • Страница 71 из 97
    5-1-3 Installing the SATA RAID/AHCI Driver and Operating System With the SATA RAID/AHCI driver diskette and correct BIOS settings, you are ready to install Windows Vista/XP onto your hard drive(s). The followings are examples of Windows XP and Vista installation. A. Installing Windows XP Step 1:
  • Страница 72 из 97
    B. Installing Windows Vista (The procedure below assumes that only one RAID array exists in your system.) Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears (RAID hard drive will not be
  • Страница 73 из 97
    Step 3: When a screen as shown in Figure 5 appears, select NVIDIA nForce RAID Controller and press Next. Figure 5 Step 4: After the driver is loaded, the screen will show the RAID hard drive. Select the RAID hard drive onto which you want to install the operating system and then press Next to
  • Страница 74 из 97
    Rebuilding an Array: Rebuilding is the process of restoring data to a hard drive from other drives in the array. Rebuilding applies only to fault-tolerant arrays such as RAID 1 array. The procedures below assume a new drive is added to replace a failed drive to rebuild a RAID 1 array. Launch the
  • Страница 75 из 97
    5-2 Configuring Audio Input and Output 5-2-1 Configuring 2/4/5.1/7.1-Channel Audio The motherboard provides three audio jacks on the back panel which can support 2/4/5.1-channel audio. To enable 7.1-channel audio, you need to install an additional 5.1/7.1 surround cable (optional) and enable the
  • Страница 76 из 97
    Audio Jacks: The 5.1/7.1 surround cable adds additional three audio jacks to the three onboard audio jacks. The picture to the right shows the default audio jack assignments. The integrated HD (High Definition) audio provides jack retasking capability that allows the user to change the function for
  • Страница 77 из 97
    Step 2: Connect an audio device to an audio jack. The The current connected device is dialog box appears. Select the device according to the type of device you connect. Then click OK. Step 3: On the Speakers screen, click the Speaker Configuration tab. In the Speaker Configuration list, select
  • Страница 78 из 97
    5-2-2 Configuring S/PDIF In/Out The S/PDIF in and out cable (optional) provides S/PDIF in and S/PDIF out functionalities. Optical S/PDIF Out Coaxial S/PDIFOut Optical S/PDIF In Coaxial S/PDIFIn S/PDIF in: The S/PDIF in jacks allow you to input digital audio signals to the computer for audio
  • Страница 79 из 97
    Step 3: Connect a S/PDIF coaxial cable or a S/PDIF optical cable (either one) to an external decoder for transmitting the S/PDIF digital audio signals. S/PDIF Coaxial Cable S/PDIF Optical Cable B. Configuring S/PDIF In and Out: B-1. Configuring S/PDIF In: On the Digital Input screen, click the
  • Страница 80 из 97
    5-2-3 Configuring Microphone Recording Step 1: After installing the audio driver, the HD Audio Manager will appear in the notification area. Doubleicon click the icon to access the HD Audio Manager. Step 2: Connect your microphone to the Mic in jack (pink) on the back panel or the Mic in jack
  • Страница 81 из 97
    Step 4: To raise the recording and playback volume for the microphone, click the Microphone Boost icon on the right of the Recording Volume slider and set the Microphone Boost level. Step 5: After completing the settings above, click Start, point to All Programs, point to Accessories, and then
  • Страница 82 из 97
    Step 3: When the Stereo Mix item appears, right-click on this item and select Enable. Then set it as the default device. Step 4: Now you can access the HD Audio Manager to configure Stereo Mix and use Sound Recorder to record the sound. 5-2-4 Using the Sound Recorder A. Recording Sound: 1. Make
  • Страница 83 из 97
    5-3 Troubleshooting 5-3-1 Frequently Asked Questions To read more FAQs for your motherboard, please go to the Support&Downloads\Motherboard\FAQ page on GIGABYTE’s website. Q: In the BIOS Setup program, why are some BIOS options missing? A: Some advanced options are hidden in the BIOS Setup program.
  • Страница 84 из 97
    5-3-2 Troubleshooting Procedure If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the problem. START Turn off the power. Remove all peripherals, connecting cables, and power cord etc. Make sure the motherboard does not short-circuit with the
  • Страница 85 из 97
    A When the computer is turned on, is the CPU cooler running? Yes No The power supply, CPU or CPU socket might fail. The problem is verified and solved. Check if there is display on your monitor. Yes No The graphics card, expansion slot, or monitor might fail. The problem is verified and solved.
  • Страница 86 из 97
    5-4 Regulatory Statements Regulatory Notices This document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. We believe that the information contained herein
  • Страница 87 из 97
    Finally, we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or
  • Страница 88 из 97
    Appendix - 88 -
  • Страница 89 из 97
    - 89 - Appendix
  • Страница 90 из 97
    Appendix - 90 -
  • Страница 91 из 97
    - 91 - Appendix
  • Страница 92 из 97
    Appendix - 92 -
  • Страница 93 из 97
    - 93 - Appendix
  • Страница 94 из 97
    Appendix - 94 -
  • Страница 95 из 97
    Contact Us  GIGA-BYTE TECHNOLOGY CO., LTD. Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei 231, Taiwan  NINGBO G.B.T. TECH. TRADING CO., LTD. - China WEB address : http://www.gigabyte.cn Shanghai TEL: +886-2-8912-4000 FAX: +886-2-8912-4003 TEL: +86-21-63410999 FAX: +86-21-63410100 Tech. and
  • Страница 96 из 97
     G.B.T. TECHNOLOGY TRADING GMBH - Germany WEB address : http://www.gigabyte.de  G.B.T. TECH. CO., LTD. - U.K.  Hungary WEB address : http://www.giga-byte.hu  Turkey WEB address : http://www.giga-byte.co.uk  GIGA-BYTE TECHNOLOGY B.V. - The Netherlands WEB address : http://www.gigabyte.com.tr 
  • Страница 97 из 97