Инструкция: диагностический сканер Autel MOT PRO

Каталог инструкций / Производители / Autel / MOT PRO

Инструкция для Autel MOT PRO

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

background image

Table of Contents

SAFETY PRECAUTIONS AND WARNINGS .............................................. 2

GENERAL INFORMATION .......................................................................... 3

............................................................. 3

........................................................ 3

OCATION OF THE

.................................... 4

.................................................................... 5

......................................................... 6

.................................................................................... 7

USING THE SCAN TOOL .............................................................................. 9

...................................................................................... 9

PECIFICATIONS

.......................................................................................... 11

............................................................................. 11

.................................................................................................. 11

........................................................................................................ 11

............................................................................................ 12

.................................................................................. 16

ROUBLESHOOTING

.................................................................... 17

PLAYBACK DATA ....................................................................................... 18

....................................................................................... 18

......................................................................................... 19

.......................................................................................... 20

DIAGNOSTICS .............................................................................................. 20

NTERING VEHICLE INFORMATION

............................................................. 20

IAGNOSTIC TEST

....................................................................................... 25

............................................................................ 29

................................................................................................. 29

............................................................................................... 31

GENERIC OBDII DIAGNOSTICS .............................................................. 32

............................................................................................... 33

www.autel-russia.ru

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

Оглавление инструкции

Страница 1 из 158
Table of Contents 1. 2. 2.1 SAFETY PRECAUTIONS AND WARNINGS .............................................. 2 GENERAL INFORMATION .......................................................................... 3 ON-BOARD DIAGNOSTICS (OBD) II ............................................................. 3
Страница 2 из 158
6.2. ERASING CODES .......................................................................................... 36 6.3. LIVE DATA .................................................................................................. 37 6.4. FREEZE FRAME
Страница 3 из 158
1. Safety Precautions and Warnings To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:     . a u r       Always perform automotive testing in a
Страница 4 из 158
2. General Information 2.1 On-Board Diagnostics (OBD) II The first generation of On-Board Diagnostics (called OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire
Страница 5 из 158
u r . a i s s u r l- e t u 2.3 Location of the Data Link Connector (DLC) .a The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic scan tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the
Страница 6 из 158
u r . a i s s u r l- 2.4 OBD II Readiness Monitors An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and
Страница 7 из 158
monitors are termed non-continuous monitors. For different ignition type engines, the available monitors are different too. The following monitors are to be used for spark ignition engines only: 1) 2) 3) 4) 5) 6) 7) EGR System O2 Sensors Catalyst Evaporative System O2 Sensor Heater Secondary air
Страница 8 из 158
including erasing of diagnostic trouble codes (DTCs) with a scan tool or a disconnected battery, can result in Readiness Monitors being set to “Not Ready”. Since the three continuous monitors are constantly evaluating, they will be reported as “Ready” all of the time. If testing of a particular
Страница 9 из 158
of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle. OBD II Drive Cycle -- A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the “ready” condition. The purpose
Страница 10 из 158
3. Using the Scan Tool 3.1 Tool Description u r . a w w 1) 2) 3) i s s u r l- e t u w .a CONNECTOR -- Connects the scan tool to the vehicle’s Data Link Connector (DLC). SD Card Slot – Holds the System SD card. LCD DISPLAY -- Indicates test results. TFT color display (320 x 240 dpi). 9
Страница 11 из 158
4) FUNCTION BUTTON – Corresponds with “buttons” on screen for executing commands. 5) ESC BUTTON -- Cancels a selection (or action) from a menu or returns to the previous screen. 6) HELP BUTTON -- Provides help information and Code Breaker function. 7) UP SCROLL BUTTON -- Moves up through menu and
Страница 12 из 158
3.2 Specifications 1) 2) Display: TFT color display (320 x 240 dpi) Operating Temperature: 0 to 60°C (32 to 140 F°) 3) Storage Temperature: -20 to 70°C (-4 to 158 F°) 4) External Power: 12.0 to 18.0 V power provided via vehicle battery or adapter. Dimensions: Length Width Height 212 mm (8.35”)
Страница 13 из 158
Cable connection to vehicle. During vehicle testing, power for the scan tool is usually provided through the vehicle cable connection. When the scan tool is not connected to a vehicle, the scan tool can be powered with an AC/DC external power adapter. u r While the scan tool is powered via the
Страница 14 из 158
4) 5) 6) LCD Test: Checks if the LCD display is working properly. Key Test: Checks if the keyboard is working properly. About: Provides information of the scan tool. Settings of the unit will remain until change to the existing settings is made. u r . a To enter the Setup menu i s s u r l- From the
Страница 15 из 158
. a i s s u r l- Figure 3.3 Unit of Measure Metric is the default measurement unit. u r 1) From System Setup screen, use the LEFT/RIGHT scroll button to select EN/METRIC unit and press the OK button. 2) From Unit of Measure screen, use the LEFT/RIGHT scroll button to select the desired unit of
Страница 16 из 158
1) From System Setup screen, use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select Beep and press the OK button. 2) From Beep Set menu, use the LEFT/RIGHT scroll button to select ON or OFF to turn on/off the beep. (Figure 3.5) u r . a i s s u r l- Figure 3.5 3) e t u Press the OK
Страница 17 из 158
1) From System Setup screen, use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select LCD Test, and press the OK button. 2) Look for missing spots in the red, green, blue, black and white LCD display. When completed, press the ESC button to exit. 3) u r . a About i s s u r l- The About
Страница 18 из 158
addition to adding new vehicle coverage through 2010/2011, we’ve also worked backwards to include non-OBDII vehicles, which can be diagnosed by setting up with optional OBDI adaptors. 3.8 Product Troubleshooting u r . a Vehicle Linking Error A communication error occurs if the scan tool fails to
Страница 19 из 158
4. Playback Data The Playback Data function allows viewing data from last test recorded by the scan tool. u r NOTE: The amount of files that can be saved depends on the space available in the SD card. . a 4.1 Reviewing Data 1) i s s u r l- Use the LEFT/RIGHT scroll button to select Playback from
Страница 20 из 158
Scan 1. UITrouble /scan/MAKE/USA/FORD/ 2. UIDatastream: complete list /scan/make/EOBD/ 3. UIFreeze /scan/make/USA/ Delete Delete All u r . a Figure 4.1 i s s u r l- If no data from previously tested vehicle is recorded, a message “No data available!” shows on the screen. 4) Review selected data on
Страница 21 из 158
4.3 Printing Data Print option allows you to print the recorded files to your computer and then to the printer. u r For more details, please refer to chapter 7. Print Data. . a 5. Diagnostics NOTE: The screens shown below in this chapter are examples. The screens actually appear vary by vehicle. i
Страница 22 из 158
u r . a i s s u r l- Figure 5.1 e t u Figure 5.2 3) .a Step by step, select the right options for your vehicle according to each screen that appears. w DAS w 1. Start New Session 2. Manual Vehicle Entry w Vehicle 1. All other Figure 5.3 Figure 5.4 21
Страница 23 из 158
Traction Assist Transmission 1. Not Equipped 2. Equipped 1. 2. 3. 4. 5. Figure 5.5 4) ASM(Auto Shift Manual) Powershift Manual Automatic DPS6 u r . a Figure 5.6 i s s u r l- Do this until the complete vehicle information is entered. Then the scan tool will ask your confirmation. Vehicle
Страница 24 из 158
Figure 5.8 RENAULT 1. VIN acquisition . a i s s u r l- Figure 5.9 VIN acquisition 1.VIN CODE automatic acquisition 2.VIN CODE manual acquisition 3.Vehicle type manual acquisition u r e t u Figure 5.10 In this mode, the scan tool will communicate with the vehicle and read off the VIN code
Страница 25 из 158
u r . a i s s u r l- Figure 5.11 In the Benz Cars menu, choose the item “2. Select by entering VIN” and you can enter the VIN code directly. Cars 1.Vehicle record and abbreviation 2.Select by entering VIN 3.All model series 4.A-Class 5.B-Class 6.C-Class/CLK 7.E-Class/CLS w w e t u w .a Figure 5.12
Страница 26 из 158
To pop up the keyboard, press the Function button corresponding to Show. Use UP/DOWN scroll button and LEFT/RIGHT scroll button to select digit and character, and then press OK button to confirm. Use Backspace button to delete the previous digit or character. When finished, press the Function
Страница 27 из 158
Depending on the scan tool model, Auto Scan function will carry out an overall scan to check the status of all systems or four systems (engine, transmission, airbag and ABS) on the vehicle being tested. Selecting Auto Scan will lead to retrieve the trouble codes in each system of the vehicle one by
Страница 28 из 158
system, the scan tool will display an option list for you to view different kind of DTCs or freeze frames. Select Option 1.CMDTCs(Continuous memory diagnostic trouble codes) 2.Freeze Frame-Mode 2 3.pending . a i s s u r l- Figure 5.17 u r In Auto Scan screen (Figure 5.16), pressing OK button will
Страница 29 из 158
3) Vehicle Information Vehicle Information function allows you to view vehicle-specific information for Specifications, System Type and other Identification. Vehicle Specification Vehicle: Mustang Engine Type: Other Capacity: 3.8L Transmission: Manual Fuel Type: Gasoline Emission Level: Federal
Страница 30 из 158
DAS 1. Start New Session 2. Manual Vehicle Entry 3. Vehicle Data Recorder Figure 5.21 u r i s s u r l- . a Click on the vehicle file you desired to enter the diagnostic menu directly. Vehicle Data Record 1. Ford1 2. Ford2 .a e t u Figure 5.22 5.3 Diagnostic Operation w This function allows you to
Страница 31 из 158
Function Menu 1. Read Codes 2. Erase Codes Figure 5.23 . a i s s u r l- Read Codes 1. KOEO On Demand Self-test 2. KOER On Demand Self-test 3. Retrieve CMDTCs(Continuous Memory Diagnostic Trouble Codes) u r e t u Figure 5.24 In the Read Codes menu, select one of the options to proceed. The screen
Страница 32 из 158
CMDTCs P0046 Battery voltage high Status-60(No additional fault symptom available for this DTC). P0098 Intake air temperature sensor 2 Circuit high input Save Figure 5.26 u r i s s u r l- . a You can save the code results for later review by selecting Save option on the bottom. When you finished
Страница 33 из 158
6. Generic OBDII Diagnostics The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. When more than one vehicle control module is detected by the scan tool, you will be prompted to select the module where the data
Страница 34 из 158
If the “LINKING ERROR” message does not go away, then there might be problems for the scan tool to communicate with the vehicle. Contact your local distributor or the manufacturer’s customer service department for assistance. u r 7） View a summary of system status (MIL status, DTC counts, Monitor
Страница 35 из 158
or with the key on engine running (KOER).  Stored Codes are also known as “hard codes”, which are fault codes, or trouble codes that have been stored in the vehicle computer memory because the faults have reoccurred for more than a specified amount of key-cycles. These codes will cause the control
Страница 36 из 158
Read Codes 1.Stored Codes 2.Pending Codes Figure 6.4 u r i s s u r l- . a If there is not any Diagnostic Trouble Code, the display indicates “No (pending) codes are stored in the module!” Wait a few seconds or press any key to return to previous screen. NOTE: Permanent Codes function is available
Страница 37 из 158
If the manufacturer of your vehicle is not listed, use the UP/DOWN scroll button to select Other and press the OK button. 6.2. Erasing Codes u r CAUTION: Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle’s on-board computer, but also “Freeze
Страница 38 из 158
3) Press the OK button to confirm. If the codes are cleared successfully, an “Erase Done!” confirmation message shows on the display.( Figure 6.7) u r Erase Codes . a Erase Done! i s s u r l- Press any key to continue . Figure 6.7 If the codes are not cleared, then an “Erase Failure. Turn Key on
Страница 39 из 158
Viewing Data The View Data function allows viewing of live or real time PID data of vehicle’s computer module(s). u r 1) To view live data, use the UP/DOWN scroll button to select Live Data from Diagnostic Menu and press the OK button. (Figure 6.3) . a i s s u r l- 2) Wait a few seconds while the
Страница 40 из 158
2) View live PIDs on the screen. Use the UP/DOWN scroll button for more PIDs if additional information is available on more than one page.( Figure 6.11) Complete List Numbers of DTCs Fuel system 1 status Fuel system 2 status Calculated load value Engine coolant temperature Pause 0 OL -0.0 -40 % 0 C
Страница 41 из 158
in the Custom List option where you could select two interacted parameter to merge and see their relationship. . a i s s u r l- Figure 6.13 u r Select Text to return to text viewing of PID data. Select Save to record retrieved live data and PID graphs. e t u Select Pause to suspend viewing. You
Страница 42 из 158
………… ..Custom List Numbers of DTCs Fuel system 1 status Fuel system 2 status Calculated load value Engine coolant temp      Select All Clear 1 2 Clear all u r . a Figure 6.14 i s s u r l- The number to the right of selected item indicates sequence of this item. If you want to deselect the
Страница 43 из 158
SD card and then use the Playback function to view the saved files. NOTE: The length of time for each frame varies per vehicle. Generally, one frame of data is about 1/4 second, or 4 frames per second. 1) u r . a To record live data, with the live data screen displaying, select Save on the bottom.
Страница 44 из 158
NOTE: The scan tool can only playback text data even though the data is saved in graphic mode. 2) When there is not enough memory space, a warning message prompting to delete previously recorded data. Save Failure Memory space not enough! Erase previously recorded Data? . a i s s u r l- Yes No u r
Страница 45 из 158
1) To view freeze frame data, use the UP/DOWN scroll button to select Freeze Frame from Diagnostic Menu and press the OK button. (Figure 6.3 ) 2) Wait a few seconds while the scan tool validates the PID MAP. 3) If retrieved information covers more than one screen, use the DOWN scroll button, as
Страница 46 из 158
to reset these monitors, the vehicle must be driven through a complete drive cycle with no trouble codes in memory. Times for reset vary depending on vehicle. Some latest vehicle models may support two types of I/M Readiness tests: A. u r Since DTCs Cleared - indicates status of the monitors since
Страница 47 из 158
4) Use the UP/DOWN scroll button, as necessary, to view the status of the MIL light (“ON” or “OFF) and the following monitors. For spark ignition engines: MIS -- Misfire Monitor FUEL -- Fuel System Monitor CCM -- Comprehensive Component Monitor EGR – EGR System Monitor O2S -- O2 Sensors Monitor CAT
Страница 48 из 158
Since DTCs cleared MIL Status Misfire Monitoring Fuel system monitoring Comprehensive component monitoring Catalyst monitoring Heated catalyst monitor OFF N/A OK OK N/A N/A u r . a Figure 6.21 i s s u r l- 5) If the vehicle supports readiness test of “This Drive Cycle”, a screen of the following
Страница 49 из 158
The O2 Monitor Test function allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle's on-board computer. The O2 Monitor Test function is not supported by vehicles which communicate using a controller area network (CAN). For O2 Monitor
Страница 50 из 158
4) View test results of selected O2 sensor. (Figure 6.25) … ……… .O2 Bank1 Sensor2 . Rich-Lean Threshd V Lean-Rich Threshd V Low for Switch (V) High for Switch (V) Rich-Lean Threshd S Lean-Rich Threshd S 5) Use the UP/DOWN scroll button to view more data if additional information is available in
Страница 51 из 158
3) The scan tool will prompt you to select the vehicle make. Vehicle Manufacturer 1/28 BUICK BMW CADILLAC CHRYSLER FORD GM . a i s s u r l- Figure 6.26 u r 4) After you select the vehicle manufacturer, the scan tool shows the On-Board Monitors tests for specific monitoring systems. 5) From On-Board
Страница 52 из 158
On-Board Monitor Test The selected mode is not supported Press any key to continue  u r . a Figure 6.28 i s s u r l- For CAN-equipped vehicles, test selections can be as below: On-Board Monitor Test 1. EGR Monitor 2. Mis-Fire Monitor Data 3. Mis-Fire Cylinder 1 Data 4. Mis-Fire Cylinder 2 Data 5.
Страница 53 из 158
Flow Test Test Value Min Limit Max Limit Status 0.10 0.00 95.0 OK % % % 8) i s s u r l- Press ESC button to return to the previous menus. 6.8. Component Test u r . a Figure 6.31 The Component Test function allows initiating a leak test for the vehicle's EVAP system. The scan tool itself does not
Страница 54 из 158
Component Test Command Sent! Press any key to continue  u r . a Figure 6.33 i s s u r l- Some vehicles do not allow scan tools to control vehicle systems or components. If the vehicle under test does not support the EVAP Leak Test, an advisory message is displayed on the screen.
Страница 55 из 158
Vehicle Info. Turn key on with engine off ! u r Press any key to continue . a Figure 6.35 i s s u r l- 3) Wait for the scan tool to display the Vehicle Info. menu. Vehicle Info. 1.Vehicle ID Number 2.Caibration ID 3.Cal. Verf. Number e t u Figure 6.36  If the vehicle does not support this mode, a
Страница 56 из 158
6) Press the ESC button to return previous menu 6.10.Modules Present The Modules Present function allows viewing of the module IDs and communication protocols for OBD2 modules in the vehicle. u r 1) Use the UP/DOWN scroll button to select Modules Present from Diagnostic Menu and press OK button.
Страница 57 из 158
DTC Lookup Only PCBU can be the first letter to be put in. Only 0~9,a~f for the rest letters... Finish Show Esc u r . a Figure 6.39 i s s u r l- 3) Select Show and a soft keyboard will pop up. Use LEFT/RIGHT button and UP/DOWN button to move to the desired character, then press OK button to
Страница 58 из 158
Use the LEFT/RIGHT scroll button to view the previous / next DTC. Select Save to record code definition. u r For manufacturer specific codes, you need to select a vehicle make on an additional screen to look for DTC definitions. . a If definition could not be found (SAE or Manufacturer Specific),
Страница 59 из 158
7. Print Data The Print Data function allows printing out diagnostic data recorded by the scan tool or customized test reports by connecting the scan tool to a PC or laptop with the USB cable supplied. MaxiDiag Elite Series scan tool A PC or laptop with USB ports A USB cable u r . a To print out
Страница 60 из 158
6) The selected data will display on the textbox of Check-Elite Printer. By selecting the function keys on the right, you could execute the following operations: Print – Print all data in the textbox to a printer connected to your computer. u r Edit – Once clicked, the software will automatically
Страница 61 из 158
8. Software Update This function allows you to update the scan tool software through a computer. u r 8.1. Register the Tool . a User would update the scan tool ONLY after you had registered the tool on our website: www.maxidas.com. Then you could download software, update online, retrieve
Страница 62 из 158
. a i s s u r l- Figure 8.1 8.2. Update Procedure u r Autel frequently releases software updates that you can download. The Update feature makes it very easy to determine and get exactly what you need. 1. Install MOT Pro PC Suit through the included CD, or download the applications in our website:
Страница 63 из 158
5. Put in the user name and password and wait for the MOT Pro Update window to display. If you forget your password unintentionally, you may always click the [Forget your password?] to link to our website and find your password back. 6. In the Update window, select the items you want to install.
Страница 64 из 158
suspended items again, then click the Update Selected Items button. The progress will resume from the break point. When the downloading is completed, the downloaded programs will be installed automatically. The new version will replace the old version. Single updating u r . a Find the desired
Страница 65 из 158
A window asking “Are you sure to delete the software?” will pop up for your confirmation. . a i s s u r l- Figure 8.4 u r Click on Yes to delete the program(s) selected, or on No to cancel the action. The deleted program will automatically add to the end of program list in the UPDATE page in case
Страница 66 из 158
9. Oil Reset 9.1 General Information u r The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. An oil change is required whenever indicated by the display and according to the recommended maintenance schedule. Whenever the oil is changed, reset the
Страница 67 из 158
3. Select Oil Reset icon in the Main Screen (Figure 3.1) and wait for the vehicle manufacturer screen. Choose the correct vehicle make. There are two ways to perform the reset service. u r A. Manual Reset . a Almost all Asian vehicles and most American and European vehicles can be reset manually by
Страница 68 из 158
Model 1.Explorer 2.Freestyle 3.Windstar Figure 9.2 . a i s s u r l- Year 1.2005 2.2003-2004 3.1998-2002 e t u u r Figure 9.3 3) After entering the vehicle information, the scan tool displays manual reset message as below. w w w .a Manual Reset 1.Select Press Reset At Oil Change from the setup
Страница 69 из 158
B. Auto Reset Most American and European vehicles can be reset automatically by the scan tool. u r NOTE: In this manner, the scan tool will communicate with the vehicle being tested. If there is a linking error, please refer to product troubleshooting. . a i s s u r l- To finish this procedure,
Страница 70 из 158
3) After you have entered the vehicle information, the oil reset screen will display as below. System u r 1.Instrument panel 2.BSI 4) . a i s s u r l- Figure 9.7 The Instrument Panel option enables you to finish oil reset service in one step by resetting the ECU to default values automatically. The
Страница 71 из 158
Service Zero Reset Check the resetting of the maintenance to zero. u r Cancel . a Figure 9.9 i s s u r l- When the resetting is finished, the tool will display a confirmation message. Service Zero Reset Operation Completed. e t u Press any key to continue Figure 9.10 5) .a The BSI option enables
Страница 72 из 158
The tool will reset the oil service to zero automatically. Resetting to zero u r Maintenance mileage zero reset carried out. . a Press any key to continue i s s u r l- Figure 9.12  In the Oil Reset menu (Figure 9.11), select Maintenance function and press OK button. The screen will display the
Страница 73 из 158
 For the Period before service or Maintenance limit, press Edit key on the bottom to pop up a soft keyboard to facilitate your input. . a i s s u r l- Figure 9.15 u r The three keyboard function keys work as below. Finish --- When you finished the input, select this key to confirm your input and
Страница 74 из 158
 When you have finished your configuration, select Finish key on the bottom of the screen, then the tool will begin the oil reset service. Maintenance i s s u r l- Press any key to continue Figure 9.17 10. EPB u r . a Configuration carried out. e t u This electric parking brake (EPB) function has
Страница 75 из 158
brake system. This can be done from the tool menu. Only carry out maintenance work when the vehicle is stationary and on level ground. Ensure that the EPB control system is reactivated after the maintenance work has been completed. u r . a NOTE: Autel accepts no responsibility for any accident or
Страница 76 из 158
System 1.EPB 2.ABS 7) u r . a Figure 11.2 i s s u r l- In the electric parking brake system screen, use the UP/DOWN button to select EPB to enter EPB system. In the EPB diagnostic function, the tool can read codes, erase codes, record live data, read ECU information, perform active test, and
Страница 77 из 158
EPB 1.Brake cable replacement 2.Electric parking brake replacement. 2) u r . a Figure 11.4 i s s u r l- In the EPB screen, use the UP/DOWN button to select Brake cable replacement. The screen shows as below. Brake cable replacement 1.Put in fitting/removal position 2.Cable tensioning 3.Electric
Страница 78 из 158
Figure 11.6 When the job is done successfully, the tool will display a message to confirm. u r Put in fitting/removal position Positioning done. To replace or remove the brake cables, refer to the mechanical schedule "Removal-replacement: electric parking brake primary and secondary cables" . a i s
Страница 79 из 158
Cable tensioning Activation in progress! OK u r . a Figure 11.9 i s s u r l- When the job is done successfully, the tool will display a message to confirm. Cable tensioning Cable tensioning done. Now calibrate the Electric parking brake (see “Electric parking brake replacement” menu) e t u Press
Страница 80 из 158
When both functions above have completed successfully, you still need to calibrate the electric parking brake system. This function is to check if the EPB is working correctly, which should be performed after work has been completed on the EPB or vehicle braking system. It will remove any air gap
Страница 81 из 158
Electric parking brake calibration Restart communication u r . a Figure 11.14 i s s u r l- When the job is done successfully, the tool will display a message to confirm. Electric parking brake calibration Electric parking brake cable calibration done! e t u Press any key to continue Figure 11.15 .a
Страница 82 из 158
3) In the EPB screen, use the UP/DOWN button to select Electric parking brake replacement. The screen shows as below. Electric parking brake replacement 1.Put in fitting/removal position 2.Cable tensioning 3.Electric parking brake calibration. . a i s s u r l- Figure 11.17 u r In the Electric
Страница 83 из 158
Active 1.Apply electric parking brake 2.Release electric parking brake u r . a Figure 11.18 i s s u r l- 3. Select a test and the tool will display an information screen as “The 'apply electric parking brake' operation is used to test the operation of the brake cables statically. If you start the
Страница 84 из 158
The test did not finish. In the first condition, the tool will display an information screen as “The operation was performed correctly. Put the vehicle on a vehicle lift and check that the rear wheels are locked. Check that the 'Electric parking brake on' message is display on the control panel and
Страница 85 из 158
In the ABS diagnostic function, the tool can read codes, erase codes, record live data, read ECU information, perform active test, and perform special function. For the functions already being described before, please refer to chapter 5. OBDII Diagnostics for details. u r Special Function 1) . a In
Страница 86 из 158
Active 1.ABS/ASR recirculation pump 2.Left front intake solenoid valve 3.Right front intake solenoid valve 4.Left rear intake solenoid valve 5.Right rear intake solenoid valve 6.Switching solenoid valve 1 7.Switching solenoid valve 2 Figure 11.22 2) u r i s s u r l- . a In the Active menu, use the
Страница 87 из 158
NOTE: AUTEL accepts no responsibility for any accident or injury arising from servicing the ABS/SRS systems. When interpreting DTCs retrieved from the vehicle, always follow the manufacturer’s recommendation for repair. u r NOTE: All software screens shown in this manual are examples, actual test
Страница 88 из 158
u r . a i s s u r l- Figure 12.1 For some vehicles, the vehicle identification procedure will ask you to select a letter which indicates one character of VIN code. (Taking Chevrolet as an example) w w e t u w .a Figure 12.2 For some vehicles, the ABS and SRS systems are divided into two systems.
Страница 89 из 158
B. Manual vehicle entry u r . a i s s u r l- Figure 12.3 This mode allows users to input and save specific vehicle information (i.e. PCM Part Number, Vehicle Calibration Number Tear Tag, and VIN) manually. This function enables direct access to the vehicle’s ABS system and makes the diagnostic
Страница 90 из 158
3) u r . a i s s u r l- Figure 12.5 4) To enable the scan tool to identify the vehicle specifications, select one of the three entries in the option screen - PCM Part Number, Calibration Number or Tear Tag - to fill up the vehicle information. Figure 12.6 Taking the PCM Part Number entry for
Страница 91 из 158
Figure 12.7 The three keys at the bottom of the screen work as below. [Finish]: After entering a new value, use this key to save the value to the tool. u r [Edit]: Press this key to pop up a soft keyboard to facilitate your input. (Figure 12.8) . a [Esc]: Press this key to exit. i s s u r l- e t u
Страница 92 из 158
C. Auto vehicle entry u r . a i s s u r l- Figure 12.9 Some vehicles provide an auto scan feature, which allows users to skip time-wasting step-by-step vehicle identification procedure and retrieve the specific vehicle information from vehicle computer directly. NOTE: This function may not be
Страница 93 из 158
select Yes to continue, otherwise select No to return to previous screen. . a i s s u r l- Figure 12.11 u r After the vehicle information is entered correctly, you will need to select SRS and ABS systems as below. 12.2 ABS Diagnostics e t u After the vehicle information is entered correctly, select
Страница 94 из 158
 Read Codes u r . a i s s u r l- Figure 12.13 This function allows user to read the ABS DTCs from vehicle ECU. 1) From the diagnostic function menu (Figure 12.13) use the UP/DOWN scroll button to select Diagnostic Trouble Codes and press the OK button. w w 2) 3) w .a e t u Figure 12.14 Use the
Страница 95 из 158
4) u r . a i s s u r l- Figure 12.15 Select Save option to store the codes or press ESC button to exit without saving.  Erase Codes This function allows user to erase the ABS DTCs in vehicle ECU. 1) NOTE: If you plan to take the vehicle to a Service Center for repair, DO NOT erase the ABS DTCs
Страница 96 из 158
Figure 12.16 4) Select Yes to continue or No to exit. When the command is sent, the tool will display a message as below: 5) . a i s s u r l- Figure 12.17 u r To make sure the codes are erased completely, perform Read DTC Information function to verify. e t u  Data Display This function enables
Страница 97 из 158
2) Use the UP/DOWN scroll button to select ABS Data or TCS Data and press the OK button to view the data streams. 3) . a i s s u r l- Figure 12.19 u r To view the live PIDs onscreen, use the UP/DOWN scroll button for all PIDs to display if additional information is available on more than one page.
Страница 98 из 158
4) Press the ESC button to return to the previous menu.  Special Functions u r . a i s s u r l- Figure 12.20 This function allows users to do various active tests or module programming. The function options vary with the vehicles being tested. 1) From the diagnostic function menu (Figure 12.13)
Страница 99 из 158
u r . a i s s u r l- Figure1 12.22 4) Take actions properly until the tool displays a completion message. w w e t u w .a Figure 12.23  Module ID Information This function allows users to view the selected control module information. 1) From the diagnostic function menu (Figure 12.13) use the
Страница 100 из 158
2) View module information present with its IDs and part numbers. 3) . a i s s u r l- Figure 12.24 u r Select Save to store the module ID information or press the ESC button to exit without saving. If the vehicle does not support ABS communication, an advisory message shows on the screen. Press ESC
Страница 101 из 158
A. Read Codes u r . a i s s u r l- Figure 12.26 This function allows user to read the SRS DTCs from vehicle ECU. 1) From the diagnostic function menu (Figure 12.26) use the UP/DOWN scroll button to select Diagnostic Trouble Codes (DTC) and press the OK button. w 2) w 3) w .a e t u Figure 12.27 Use
Страница 102 из 158
4) u r . a i s s u r l- Figure 12.28 Select Save option to store the codes or press ESC button to exit without saving. B. Erase Codes This function allows user to erase the SRS DTCs in vehicle ECU. NOTE: If you plan to take the vehicle to a Service Center for repair, DO NOT erase the SRS DTCs from
Страница 103 из 158
Figure 12.29 4) Select Yes to continue or No to exit. When the command is sent, the tool will display a message as below: 5) . a i s s u r l- Figure 12.30 u r To make sure the codes are erased completely, perform Read DTC Information function to verify. C. Data Display e t u This function enables
Страница 104 из 158
2) Use the UP/DOWN scroll button to select SIR Data and press the OK button to view the data streams. 3) . a i s s u r l- Figure12.32 u r To view the live PIDs onscreen, use the UP/DOWN scroll button for all PIDs to display if additional information is available on more than one page. The function
Страница 105 из 158
D. Special Functions This function allows users to do various active tests or module programming. The function options vary with the vehicles being tested. u r 1) From the diagnostic function menu (Figure 12.26) use the UP/DOWN scroll button to select Special Functions and press the OK button. 2)
Страница 106 из 158
E. Module ID Information This function allows users to view the selected control module information. 1) From the diagnostic function menu (Figure 12.26) use the UP/DOWN scroll button to select Module ID Information and press the OK button. 2) View module information present with its IDs and part
Страница 107 из 158
13. SAS (Steering Angle Sensor) Calibration Steering Angle Sensor Calibration permanently stores the current steering wheel position as the straight-ahead position in the steering angle sensor EEPROM. Therefore, the front wheels and the steering wheel must be set exactly to the straight-ahead
Страница 108 из 158
Take Toyota as an example. While performing the Zero Point Calibration on Toyota vehicles, do not tilt, move or shake the vehicle. The vehicle must remain in a stationary condition throughout the entire process. Be sure to perform the procedure on a level surface with an inclination of less than
Страница 109 из 158
u r . a i s s u r l- Figure 13.1 e t u K. Use the UP/DOWN scroll button to select VGRS in the menu. The screen displays as below. w w w .a Figure 13.2 13.1 Read Codes This function allows user to read the SAS DTCs from vehicle ECU. 1) From the function menu (Figure 13.2) use the UP/DOWN scroll
Страница 110 из 158
2) View DTCs and their definitions on screen. 3) . a i s s u r l- Figure 13.3 u r 13.2 Select Save option to store the codes or press ESC button to exit without saving. Erase Codes This function allows user to erase the SAS DTCs in vehicle ECU. e t u 1) From the function menu (Figure 13.2) use the
Страница 111 из 158
4) u r . a i s s u r l- Figure 13.5 13.3 To make sure the codes are erased completely, perform Read Codes function to verify. Freeze Frame Data This function allows user to view the vehicle’s operating parameters at the moment a DTC is detected. e t u 1) From the function menu (Figure 13.2) use the
Страница 112 из 158
This function enables users view SAS-related data readings from a selected ECU. With the live data screen displayed, you can view the data in Text or graphical format, record and save files for later viewing, pause the readings and view past data, and more. u r From the function menu (Figure 13.2)
Страница 113 из 158
 Press the corresponding FUNCTION BUTTON ‘Stop Save’ to stop saving data and resume live sensor data retrieving.  Press the corresponding FUNCTION BUTTON ‘Pause’ to suspend live sensor data retrieving.  Press the corresponding FUNCTION BUTTON ‘Continue’ to resume live sensor data retrieving. 
Страница 114 из 158
2) Use the UP/DOWN scroll button to move to the desired item and press the corresponding FUNCTION BUTTON ‘Select’ to choose.    . a i s s u r l- Figure 13.10 u r The Selected items are marked with ticks on the left. The number on the right indicates sequence of the selected item. Press the
Страница 115 из 158
A. Steering Angle Adjust u r . a i s s u r l- Figure 13.11 1) From the Utility function menu (Figure 13.11) use the UP/DOWN scroll button to select Steering Angle Adjust and press the OK button. 2) The tool will display a series of instructions. Follow the onscreen instructions step by step until
Страница 116 из 158
1) From the Utility function menu (Figure 13.11) use the UP/DOWN scroll button to select Records Clear and press the OK button. 2) The tool will display a list of records. u r . a i s s u r l- Figure 13.13 3) Select Clr Histroy to continue operation or ESC to exit. When the command is sent, the
Страница 117 из 158
3) u r . a i s s u r l- Figure 13.15 When the command is sent, the tool will display a message as below. w w w .a e t u Figure 13.16 116
Страница 118 из 158
14. DPF service 14.1 DPF safety The DPF function allows you to carry out numerous functions on the Diesel Particulate Filter system without having to send the car to a main dealer. The tool will retrieve/erase DPF-related codes, reset the DPF light after the filter has been replaced, micromanage
Страница 119 из 158
NOTE: All software screens shown in this manual are examples, and actual test screens may vary for each vehicle being tested. Observe the menu titles and onscreen instructions to make correct option selections. u r NOTE: If the vehicle needs to be driven in order to perform a DPF service, ALWAYS
Страница 120 из 158
u r . a i s s u r l- Figure 14.1 8. The screen displays as below. w e t u w .a Figure 14.2 14.2 DPF Diagnostics w Use the UP/DOWN scroll button to select Control Units in the menu. (Figure 14.2）The computer will automatically detect the DPF-related system, DDE, which is dedicated for BMW. For other
Страница 121 из 158
14.2.1 Read Codes u r . a i s s u r l- Figure 14.3 This function allows user to read the DPF DTCs from vehicle ECU. 1) From the function menu (Figure 14.3) use the UP/DOWN scroll button to select Read Codes and press the OK button. 2) View DTCs and their definitions on screen. 3) w .a e t u w
Страница 122 из 158
2) A warning message will come up asking your confirmation. 3) Select Yes to continue or No to exit. When the command is sent, the tool will display a message as below. 4) 14.4 . a i s s u r l- Figure 14.5 u r Figure 14.6 To make sure the codes are erased completely, perform Read Codes function to
Страница 123 из 158
u r . a i s s u r l- Figure 14.7 2) In this function list, Diagnosis requests retrieves signal data generated by the sensors, Cruise control shows the driving conditions, and Particulate filter displays the DPF system status information. (Taking Particulate filter as an example.) 3) Select only the
Страница 124 из 158
u r . a i s s u r l- Figure 14.9  Press the corresponding FUNCTION BUTTON ‘Save’ to store the retrieved live data for later playback or printing.  Press the corresponding FUNCTION BUTTON ‘Stop Save’ to stop saving data and resume live sensor data retrieving.  Press the corresponding FUNCTION
Страница 125 из 158
3) u r . a i s s u r l- Figure 14.10 Select Save option to save the information for later review or press the ESC button to return to the previous menu. 14.6 DPF Service Functions Use the UP/DOWN scroll button to select Service Functions in the menu. (Figure 14.2）The screen displays as below. w w
Страница 126 из 158
2) The tool communicates with the vehicle and reads the fault codes memory. Follow the on-screen instructions to finish this procedure. u r . a i s s u r l- e t u Figure 14.12 3) The tool will display a function list menu as below. In this menu, you can enter new value for adjustment, or reset
Страница 127 из 158
【2】Reset adjustment to 0 【3】End with programming (the new value is permanently stored) 【4】End without programming (the old value is retained) A. Enter new value for adjustment u r . a From the Starting Basic Inspection Quantity menu (Figure 14.13) use the LEFT/RIGHT scroll button to select 【1】 and
Страница 128 из 158
The three keys at the bottom of the screen work as below. u r . a i s s u r l- Figure 14.15 [Finish]: When you finished the input, select this key to confirm your input and exit. [Pre.] : Moves a space to the left. [Backspace]: Uses this key to erase the previous digit or character when typing. e t
Страница 129 из 158
This function enables you to adjust the injection volume. 1) From the service functions menu (Figure 14.11) use the UP/DOWN scroll button to select Injection rate and press the OK button. 2) The tool communicates with the vehicle and reads the fault codes memory. Follow the on-screen instructions
Страница 130 из 158
The three keys at the bottom of the screen work as below. u r . a i s s u r l- Figure 14.17 [Finish]: After entering a new value, use this key to save the value to the tool. [Show]: Press this key to pop up a soft keyboard to facilitate your input. (Figure 14.18) [Esc]: Press this key to exit. w w
Страница 131 из 158
NOTE: The data you input must be in the reasonable range. If the input data is out of range, the tool will display a warning message “Permissible adjustment range exceeded.” B. Reset adjustment to 100% u r From the Injection rate menu (Figure 14.16) use the LEFT/RIGHT scroll button to select 【2】and
Страница 132 из 158
The option keys at the bottom of the screen work as below. 【EDIT 1】Edit Cylinder 1 injector code u r . a i s s u r l- Figure 14.19 【EDIT 2】Edit Cylinder 2 injector code 【EDIT 3】Edit Cylinder 3 injector code e t u 【EDIT 4】Edit Cylinder 4 injector code 【Back】Return to the previous menu
Страница 133 из 158
The three keys at the bottom of the screen work as below. u r . a i s s u r l- Figure 14.20 [Finish]: After entering a new value, use this key to save the value to the tool. [Show]: Press this key to pop up a soft keyboard to facilitate your input. (Figure 14.21) [Esc]: Press this key to exit. w w
Страница 134 из 158
B. Restore the old value From the Injector rate adjustment menu (Figure 14.19) use the LEFT/RIGHT scroll button to select 【Restore】 and press the OK button. The tool will automatically retain the old value. u r When you have finished the injector rate adjustment, use the LEFT/RIGHT scroll button to
Страница 135 из 158
3) If every prerequisite is met, the tool will ask your confirmation to proceed as below. Select Request to begin a regeneration or End to end the service function and exit. 4) . a i s s u r l- Figure 14.23 u r A series of instruction screens appears for users to perform the particle filter
Страница 136 из 158
Figure 14.24 5) . a i s s u r l- Figure 14.25 u r When the particle filter regeneration is complete, the tool will ask your confirmation to exit the display. Select Repeat to check the status again or End to end the service function and exit. w w w .a e t u Figure 14.26 NOTE: In the case of a
Страница 137 из 158
be seen exclusively with the vehicle stationary with the engine running. This behavior does not impair the scheduled course of the regeneration in general. 14.6.5 Particle filter test u r It is advisable to carry out a series of particle filter tests as a result of constant DPF regeneration, such
Страница 138 из 158
4) The tool shows a list of particle filter tests as below. .a e t u Figure 14.29 The option keys at the bottom of the screen work as below. w 【1】Visual inspection of engine oil 【2】Visual inspection of particulate filter w 【3】Function check of swirl flaps w 【4】Exhaust backpressure test
Страница 139 из 158
a) From the particle filter test menu (Figure 14.29) use the LEFT/RIGHT scroll button to select 【1】and press the OK button. b) Select No if you visually find nothing wrong with your engine oil. The tool displays as below. Press OK button to return to previous menu. w w c) . a i s s u r l- Figure
Страница 140 из 158
d) Or, select Test Selection to return to previous menu. 【2】Visual inspection of particulate filter a) u r . a i s s u r l- Figure 14.32 From the particle filter test menu (Figure 14.29) use the LEFT/RIGHT scroll button to select 【2】and press the OK button. w b) w w .a e t u Figure 14.33 Select Yes
Страница 141 из 158
c) u r . a i s s u r l- Figure 14.34 d) Or, select No if you visually find soot on the inside of the exhaust tail pipes. The tool displays as below. Follow the on-screen instructions to carry out particle filter visual inspections. Then select the correct options according to the test results. w .a
Страница 142 из 158
b) u r . a i s s u r l- Figure 14.36 c) Select OK to activate swirl flaps and the tool displays as below. (Figure 14.37) Press OK button to end the activation and exit. .a e t u Figure 14.37 Or, select Cancel to return to previous menu. w 【4】Exhaust backpressure test w a) w From the particle filter
Страница 143 из 158
b) u r . a i s s u r l- Figure 14.38 c) Press OK button to proceed and the tool displays as below. Or, select Cancel to return to previous menu. Figure 14.39 Check the exhaust backpressure with engine running idle. The tool will read off the actual backpressure value and compare with the upper
Страница 144 из 158
Figure 14.40  If the engine is not running at idle speed, the tool will display a warning message. (Figure 14.41) Select OK to repeat the test or select Cancel to exit. u r . a i s s u r l- Figure 14.41 d) Check the exhaust backpressure with engine running at 2000 rpm. The tool will read off the
Страница 145 из 158
e) u r . a i s s u r l- Figure 14.43  Check the exhaust backpressure with engine running at cut-off speed. The tool will read off the actual backpressure value and compare with the upper limit. (Figure 14.44). Select OK to end the test or Cancel to return to previous menu. Figure 14.44 If the
Страница 146 из 158
f) The tool will submit a confirmation.(Figure 14.46) summary for your u r . a i s s u r l- Figure 14.46 g) report Select Yes if the actual values exceed the limits. The tool displays an instruction message as below. Press OK button to return to previous menu. w h) w w .a e t u Figure 14.47 Or,
Страница 147 из 158
i) Or, select Test Selection to return to previous menu. 【5】Actual/target value check-mass air flow sensor a) b) u r . a i s s u r l- Figure 14.48 From the particle filter test menu (Figure 14.29) use the LEFT/RIGHT scroll button to select 【5】 and press the OK button. w w w .a e t u Figure 14.49
Страница 148 из 158
15. TPMS (Tire Pressure Monitor System) u r This function allows user quickly look up vehicle TPMS information and reset procedures and perform Tire Pressure Monitor System diagnostics. . a With the tool properly connected to a vehicle's data link connector (DLC), you can use the tool to read TPMS
Страница 149 из 158
Please refer to 3.8 Product Troubleshooting for more details. . a i s s u r l- Figure 15.1 15.2 TPMS diagnostics  Read Codes u r This function enables you to read TPMS-related diagnostic trouble codes (DTCs) from a selected ECU. e t u 1) From the TPMS diagnostic function menu (Figure 15.1), use
Страница 150 из 158
This function enables you to erase TPMS-related diagnostic trouble codes (DTCs) in a selected ECU. 1) From the TPMS diagnostic function menu (Figure 15.1), use the UP/DOWN scroll button to select the Erase Codes, and press OK button. 2) The tool will display a warning message for your confirmation.
Страница 151 из 158
viewing, sort the data, pause the readings and view past data, and more. From the TPMS diagnostic function menu (Figure 6.1), use the UP/DOWN scroll button to select the Live Data, and press OK button. u r . a i s s u r l- Figure 15.5 All Data e t u 1) From the Live Data menu (Figure 15.5), use the
Страница 152 из 158
 Press the corresponding FUNCTION BUTTON ‘Pause’ to suspend live sensor data retrieving.  Press the corresponding FUNCTION BUTTON ‘Continue’ to resume live sensor data retrieving.  If the ‘One Graphic’ option is highlighted when a specific item is selected, the graphic information is available.
Страница 153 из 158
This option lets you select and view TPMS-related data readings for specific components (sensors, switches, etc.) controlled by a specific ECU. 1) To retrieve customized live sensor data, use the UP/DOWN scroll button to select Custom List from Live Data and press the OK button. (Figure 15.5) Use
Страница 154 из 158
2) The tool will display a list of available active tests for the vehicle being tested. . a i s s u r l- Figure 15.10 Taking Warning Lamp for example: u r 1) From Active Test Menu, use the UP/DOWN scroll button to select Warning Lamp function. (Figure 15.10) 2) Press the corresponding FUNCTION
Страница 155 из 158
1) 2) From the TPMS diagnostic function menu (Figure 15.1), use the UP/DOWN scroll button to select the Special Function, and press OK button. The tool will display a list of available special functions for the vehicle being tested. u r . a i s s u r l- Figure 15.12 Taking ID Regist for example: e
Страница 156 из 158
1) 2) From the TPMS diagnostic function menu (Figure 15.1), use the UP/DOWN scroll button to select the Ecu Information, and press OK button. The tool will display the Ecu information for your viewing and saving. u r . a i s s u r l- Figure 15.14 Select Save option to save the information for later
Страница 157 из 158
3) Autel shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of the scan tool. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. 4) All information in this manual is based
Страница 158 из 158