Register your product and get support at
www.philips.com/welcome
CMP100
EN
User manual
RU
Руководство пользователя
b
a
d
e
c
a
l
k
j
b
c
d
h
i
320Hz
30Hz
SUB
WOOFER
SUBSONIC
ON OFF
REMOTE
LEVEL CONTROL
f e
g
4 ohm speaker
Динамик 4 Ом
4 ohm speaker
4 ohm speaker
Динамик 4 Ом
Динамик 4 Ом
Left speaker
Right speaker
White / Black
White
Grey
Grey / Black
Car audio unit
320Hz
30Hz
SUB
WOOFER
SUBSONIC
ON OFF
REMOTE
LEVEL CONTROL
Левый громкоговоритель
Правый громкоговоритель
Автомобильное
аудиоустройство
Белый
Серый
Белый/черный
Серый/черный
LINE OUT
Car audio unit
320Hz
30Hz
SUB
WOOFER
SUBSONIC
ON OFF
REMOTE
LEVEL CONTROL
Автомобильное
аудиоустройство
Линейный выход
to a metal point of the car
Car audio unit
Remote output
Fuse (60 A)
+12 V car battery
less than 450 mm (18 in)
К металлическому контакту в автомобиле
Выход для пульта ДУ
Автомобильное
аудиоустройство
Менее 450 мм (18 дюймов)
Плавкий предохранитель (60 А)
Автомобильный аккумулятор +12 В
A
G
C
E
F
D
B
H
a
a
b
b
320Hz
30Hz
SUB
WOOFER
SUBSONIC
ON OFF
REMOTE
LEVEL CONTROL
REMOTE
LEVEL CONTROL
English
1. Important
Safety
•
Read and understand all instructions before you use the apparatus.
If damage is caused by failure to follow instructions, the warranty does
not apply.
This unit is designed for negative ground (earth) 12 V DC operation only.
•
Use only the supplied mounting hardware for a safe and secure installation.
•
Do not connect any active speakers (with built-in amplifier) to the speaker
•
terminals of the unit. Doing so may damage the active speakers.
To ensure safe driving, adjust the volume to a safe and comfortable level.
•
To avoid short circuit, do not expose the apparatus to rain or water.
•
Never expose the apparatus to direct sunlight, naked flames or heat.
•
Clean the apparatus with soft, damp cloth. Never use substances such as
•
alcohol, chemicals or household cleaners on the apparatus.
Notice
Environmental information
All unnecessary packaging has been omitted. We have tried to make the
packaging easy to separate into three materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled
by a specialized company. Please observe the local regulations regarding the
disposal of packaging materials, exhausted batteries and old equipment.
Any changes or modifications made to this device that are not expressly
approved by Philips Consumer Lifestyle may void the user’s authority to
operate the equipment.
2009 © Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners. Philips reserves the right to change products at any time
without being obliged to adjust earlier supplies accordingly.
2. Your car power amplifier
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With the amplifier, you can enjoy high quality sound performance with
powerful bass and beats.
What’s in the box
A
Check and identify the contents of your package:
a
Amplifier
b
Screw_4x25mm (x4)
c
Fuse (x2)
d
Hi input connector (x1)
e
Volume controller
Overview of the main unit
B
a
INPUT L/R
•
Connect car audio with RCA cable.
b
HI INPUT
Connect car audio with the supplied high input connector.
•
c
INPUT LEVEL
Adjust input level (0.3V to 6V).
•
d
BASS BOOST
Boost the frequencies at around 45Hz to a maximum of 12dB.
•
e
SUBWOOFER
Adjust low-pass-f
•
ilter frequency for subwoofer.
f
PROTECT
Light in red when the PROTECTOR is activated.
•
g
POWER
Light in blue when power is turned on.
•
h
SUBSONIC ON/OFF
Switch on or off the subsonic filter.
•
i
REMOTE LEVEL CONTROL
External remote
•
controller for volume level control.
j
POWER (GND/REM/+12V)
Connect +12V DC power cable, ground wire and remote wire.
•
k
Fuse: 30Ax2
l
SPEAKER OUTPUT
Connect to subwoofers.
•
3. Installation
Installation
C
You can mount the amplifier either under a seat or on the rear tray.
Note
To avoid interference, do not place the amplifier too close to the car audio or antenna.
•
The supplied mounting screws are 25mm long. Make sure that the mounting
•
board is thicker than 25mm.
1
Place the unit on the location for installation.
2
Mark the positions of the four screw holes.
3
Drill the holes with driller of approximately 4mm in diameter.
4
Mount the unit with the supplied screws.
Connect speakers
D
Note
Use speakers with an impedance of 2 to 8 ohm (4 to 8 ohm when used as a
•
bridged amplifier).
Match the “left”, “right”, “+” and “-” terminals correctly. Revised polarity may
•
degrade sound quality.
Option 1: Mono bridged mode: connect 1 speaker
a
Option 2: Stereo mode: connect 2 speakers
b
Connect car audio
E
Option 1: High level input connection
a
Connect the amplifier to your car audio with the supplied High level
input connector.
Option 2: Line input connection
b
Connect the amplifier to the car audio with a RCA cable (not supplied).
Connect power
F
1
Make the power connection as illustrated below:
Connect the ground wire from the car to the
•
GND
socket.
Connect the remote wire from the car audio to the
•
REM
socket.
√ With this connection, you can turn on/off the amplifier
with the car audio.
Connect the power wire from the car battery to the
•
+12V
socket.
Tip
If your car audio does not have remote output, connect the remote input
•
terminal (REM) to the accessory power supply.
4. Use your power amplifier
Adjust input level
You can adjust the input voltage from 0.3V to 6V.
1
Rotate
INPUT LEVEL
to adjust input voltage.
Adjust bass boost
You can punch extra bass for 0 to 12dB.
1
Rotate
BASS BOOST
to punch for extra bass.
About the protector indicator
The amplifier has a built-in protection circuit to protect the transistors
and speakers when:
The unit is overheated. Or
•
A DC current is generated. Or
•
The battery voltage is over low or over high. Or
•
The speaker terminals are short circuited.
•
When the PROTECT indicator lights up in red, the unit shuts down
automatically. If this happens, please:
1
Take out the disc or tape and turn off the car audio.
2
Check the cause of the malfunction (see above).
3
If the amplifier has overheated, wait until the unit cools down
before use.
Adjust subwoofer frequency
Rotate Subwoofer to adjust low-pass-f ilter frequency for subwoofer.
1
Rotate
SUBWOOFER
to adjust frequency: 30Hz to 320Hz.
Turn subsonic f ilter on or off
1
Slide
SUBSONIC
to ON position.
The subsonic is turned on, frequency below 15Hz is f
•
iltered.
To turn off the subsonic filter, slide
•
SUBSONIC ON/OFF
to
OFF position.
Adjust volume
G
You can adjust volume at the front seat via the supplied volume control.
1
Connect the supplied volume controller to the
REMOTE LEVEL
CONTROL
socket.
2
Rotate the volume knob to adjust volume.
Replace fuse
H
If there is no power, the fuse may be damaged and need to be replaced.
1
Pull out the damaged fuse.
2
Replace the fuse with the supplied fuses or to buy two fuses
that matches the voltage of the damaged fuse (30Ax2).
If the fuse gets damaged immediately after it has been replaced, there
may be an internal malfunction. In such case, consult your Philips dealer.
5. Product information
Note
Product information is subject to change without prior notice.
•
Power Output (RMS)
- 4 ohm
- 2 ohm
250Wx1
400Wx1
Total harmonic distortion
0.08%
Signal to noise ratio
105dB
Frequency response
5-320Hz
Input sensitivity
300mV-6V
Input impedance
22k ohm
Fuse rating
30Ax2
Dimensions (DxWxH)
54.4x336.5x240.2mm
CMP100_51_UM_V2.0_EN+RU.indd 1
12/9/2009 3:07:47 PM
