Инструкция для ASROCK H77M-ITX

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

26

ASRock  H77M-ITX  Motherboard

 

English

System Panel Header 

This header accommodates 

(9-pin PANEL1)

 

several system front panel 

(see p.2,  No. 8)

 

functions.

 

Connect the power switch, reset switch and system status indicator on the 
chassis to this header according to the pin assignments below. Note the 
positive and negative pins before connecting the cables.

 

PWRBTN (Power Switch):

 

Connect to the power switch on the chassis front panel. You may configure 
the way to turn off your system using the power switch.

 

RESET (Reset Switch):

 

Connect to the reset switch on the chassis front panel. Press the reset 
switch to restart the computer if the computer freezes and fails to perform a 
normal restart.

 

PLED (System Power LED):

 

Connect to the power status indicator on the chassis front panel. The LED 
is on when the system is operating. The LED keeps blinking when the sys-
tem is in S1/S3 sleep state. The LED is off when the system is in S4 sleep 
state or powered off (S5).

 

HDLED (Hard Drive Activity LED):

 

Connect to the hard drive activity LED on the chassis front panel. The LED 
is on when the hard drive is reading or writing data.

 

The front panel design may differ by chassis. A front panel module mainly 
consists of power switch, reset switch, power LED, hard drive activity LED, 
speaker and etc. When connecting your chassis front panel module to this 
header, make sure the wire assignments and the pin assign-ments are 
matched correctly.

Chassis Fan Connector 

 

Please connect the chassis fan 

(4-pin CHA_FAN1)

 

 

cable to the connector and 

(see p.2,  No. 17)

 

 

match the black wire to the 

 

 

ground pin. 

FAN_SPEED_CONTROL

GND

+12V

CHA_FAN_SPEED

CPU Fan Connectors 

 

Please connect the CPU fan 

(4-pin CPU_FAN1)

 

 

cable to the connector and 

(see p.2,  No. 16)

 

 

match the black wire to the 

 

 

ground pin.

4  

3  

2  

1

GND

+12V

CPU_FAN_SPEED

FAN_SPEED_CONTROL

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190