Инструкция для CISCO SYSTEMS WES610N

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

Advanced Configuration

Linksys WES610N/WET610N

ERP Protection Type

This option configures protection of OFDM packets

despite  the  presence  of  802 11b  stations  within  the  wireless  network   By
sending RTS/CTS or CTS2Self packets in 802 11b rates, the bridge informs the
wireless network that OFDM packets are going to be transferred and protects
the packets in the wireless network  The RTS/CTS and CTS2Self packets create
overhead, which may result in lower throughputs

The  RTS/CTS  option  provides  better  coverage  but  lower  throughputs  when
compared to CTS2Self, because the RTS/CTS option includes acknowledgement
from the receiving device  To use the RTS/CTS option, keep the default, RTS/
CTS  The None option may cause collisions between OFDM and CCK packets  To
use the None option, select None  To use the CTS2Self option, select CTS2Self

11n Protection Type

This option configures protection from non-High

Throughput (HT) devices within the wireless network In case the wireless
router (or access point) detects an association of a non-HT legacy device, it will
signal all the HT devices to use RTS/CTS or CTS2Self mechanisms before each
data transmission This feature also supports all 802 11n standard protections,
including MIMO

The  RTS/CTS  option  provides  better  coverage  but  lower  throughputs  when
compared to CTS2Self, because the RTS/CTS option includes acknowledgement
from the receiving device  To use the RTS/CTS option, keep the default, RTS/
CTS  The None option may cause collisions between HT and legacy packets  To
use the None option, select None  To use the CTS2Self option, select CTS2Self

Percentage of maximal transmit power

This option sets the percentage

of maximal transmit power relative to the regulatory domain restrictions  For
example,  if  the  regulatory  domain  restriction  allows  transmissions  of  up  to
20 dB, then setting the percentage at 50% allows maximal transmit power of
10 dB  Select the percentage you want to use: 12%, 25%, 50%, or 100%  The
default is 100%

QoS Classification Type

This option sets 802 1D or 802 1Q mapping from the

IP DSCP/TOS field to WMM priorities (Background, Best Effects, Video, Voice)
Keep the default, 802.1D, or select 802.1Q, which is used by some IPTV streams

Re-establish Ethernet connection when initiating wireless connection

trigger DHCP discovery from the device that resides behind the bridge, the
bridge will reset the Ethernet link between the bridge and the device every
time a wireless connection is established To disable this behavior, select No
Otherwise, keep the default, Yes

Click Save Settings to apply your changes, or click Cancel Changes to cancel
your changes

Administration > Management

Use this screen to manage specific bridge functions: access to the web-based
utility, backup of the configuration file, and reboot

Management

Bridge Access

Use a password to protect access to the browser-based utility

Bridge Password

Enter a new Password for the bridge

Re-enter to confirm

Enter the Password again to confirm

Idle Timeout

The login times out after a period of inactivity that you specify

The range is 60 to 3600 seconds The default is 600

Web Access

Access via Wireless

If you are using the bridge in a public domain where you

are  giving  wireless  access  to  your  guests,  you  can  disable  wireless  access  to
the bridge’s browser-based utility  You will only be able to access the browser-
based utility via a wired connection if you disable the setting  Keep the default,
Enabled, to allow wireless access to the bridge’s browser-based utility, or select
Disabled to block wireless access to the utility

Backup and Restore

Backup

To back up the bridge’s configuration file, click Backup Configurations

Then follow the on-screen instructions