Страница 3 из 42 GENERAL SAFETY RULES WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless)
Страница 4 из 42 the wheel to the collet must be minimal. If the mandrel is insufficiently held and/or the overhang of the wheel is too long, the mounted wheel may become loose and ejected at high velocity. Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and
Страница 5 из 42 any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel
Страница 6 из 42 TECHNICAL DATA Straight grinder Rated power No load speed Maximum diameter of grinding wheel/disc Clip diameter Weight according EPTA-Procedure 01/2003 The instructions contained in this manual must be strictly followed, it should be carefully read and kept close at hand to use when carrying out
Страница 7 из 42 metals. Fine toothing: hard steels, hardened steels. Felt Wheels (C) These require paste for polishing. Valve grinding, shiny finishing of ground or polished surfaces. Fans (D) Dies and moulds and light deburring work. Wire Brush (E) Steel wire: for cleaning rusty surfaces. Brass wire: for matt
Страница 8 из 42 NORMAS GENERALES DE SEGURIDAD ¡ATENCIÓN! Leer todas las instrucciones. El incumplimiento de cualquiera de las siguientes instrucciones puede provocar choques eléctricos, incendios y/o lesiones graves. La expresión “herramienta eléctrica” que aparece en todas las siguientes advertencias se refi ere
Страница 9 из 42 únicamente recambios idénticos. Esto garantiza la constante seguridad de la herramienta eléctrica. ADVERTENCIA! Rogamos leer las indicaciones de seguridad y las instrucciones, también las que contiene Instrucciones de servicio. MEDIDAS ESPECIALES DE SEGURIDAD Instrucciones de seguridad comunes para
Страница 10 из 42 Ello puede hacerle perder el control sobre la herramienta eléctrica y hacer que ésta salga impulsada en dirección opuesta al sentido de giro que tenía el útil. En el caso, p. ej., de que un disco amolador se atasque o bloquee en la pieza de trabajo, puede suceder que el canto del útil que penetra
Страница 11 из 42 proyectados a gran velocidad pequeñas partículas o fragmentos de alambre capaces de traspasar la piel. Instrucciones de seguridad adicionales Utilice unos aparatos de exploración adecuados para detectar posibles tuberías de agua y gas o cables eléctricos ocultos, o consulte a la compañía local que
Страница 12 из 42 CARACTERÍSTICAS TÉCNICAS Amoladoras rectas Potencia absorbida Velocidad en vacío Diámetro máx. muela/disco Diámetro pinza Peso según EPTA-Procedure 01/2003 Respetar escrupulosamente las instrucciones contenidas en este manual, leerlo con atención y tenerlo a mano para eventuales controles de las
Страница 13 из 42 Blanda: Materiales duros, superficies lisas, mayor desbaste, pulido fino. Dura: Materiales blandos, superficies ásperas y aristas, menos desbaste y mayor duración, alta calidad de superficie. Fresa metal duro (B) Dentado basto: Acero inoxidable, aceros aleados, metales ligeros. Dentado fino: Aceros
Страница 14 из 42 NORMES GÉNÉRALES DE SÉCURITÉ ATTENTION! Lire toutes les instructions. Ne pas se conformer à toutes les instructions énumérées ci-dessous peut donner lieu à des secousses électriques, des incendies et/ou des lésions sérieuses. Le terme «outil électrique» de tous les avertissement énumérés ci-dessous
Страница 15 из 42 dans la Mode d’emploi. CONSIGNES SPÉCIFIQUES DE SÉCURITÉ Avertissements de sécurité communs pour les opérations de meulage, de brossage métallique, de lustrage ou de façonnage: Cet appareil électrique est à utiliser en tant que meuleuse, modeleuse, outil à façonner et en tant que brosse métallique.
Страница 16 из 42 en rotation qui, à son tour, contraint l’outil électrique hors de contrôle dans le sens opposé de rotation de l’accessoire au point du grippage. Par exemple, si une meule abrasive est accrochée ou pincée par la pièce à usiner, le bord de la meule qui entre dans le point de pincement peut creuser la
Страница 17 из 42 dans la position d’arrêt, si l’alimentation en courant est interrompue, par ex. par une panne de courant ou quand la fiche du secteur est débranchée. Ceci permet d’éviter un redémarrage incontrôlé. Bloquer la pièce à travailler. Une pièce à travailler serrée par des dispositifs de serrage
Страница 18 из 42 CARACTÉRISTIQUES TECHNIQUES Meuleuses droites Puissance absorbée Vitesse à vide Diamètre maximal meule/disque Diamètre de la pince Poids suivant EPTA-Procédure 01/2003 Respecter strictement les instructions contenues dans ce manuel qu’il convient de lire attentivement et de conserver à portée de
Страница 19 из 42 ébauchage, polissage fin. Dure : Matériaux tendres, surfaces rugueuses et arêtes, moins d’ébauchage et plus longue durée, haute qualité de surface. Fraise métal dur (B) Denture grosse : Acier inoxydable, aciers a alliages, métaux légers. Denture fine : Aciers durs, aciers trempes. Roue a feutre (C)
Страница 20 из 42 NORME DI SICUREZZA GENERALE ATTENZIONE! Leggere tutte le istruzioni. La mancata ottemperanza a tutte le istruzioni sotto elencate può dare luogo a scosse elettriche, incendi e/o lesioni serie. Il termine “utensile elettrico” di tutte le avvertenze elencate qui sotto si riferisce agli utensili
Страница 21 из 42 raccomandato per questo elettroutensile. Il semplice fatto che un accessorio possa essere fissato al Vostro elettroutensile non è una garanzia per un impiego sicuro. Il numero di giri ammesso dell’accessorio impiegato deve essere almeno tanto alto quanto il numero massimo di giri riportato
Страница 22 из 42 dall’operatore a seconda della direzione di rotazione che ha nel momento in cui si blocca. In tali situazioni è possibile che le mole abrasive possano anche rompersi. Un contraccolpo è la conseguenza di un utilizzo non appropriato oppure non corretto dell’elettroutensile. Esso può essere evitato
Страница 23 из 42 dell’acqua si provocano seri danni materiali oppure vi è il pericolo di provocare una scossa elettrica. Se l’alimentazione di corrente viene interrotta p. es. a causa di mancanza di corrente oppure di estrazione della spina di rete, sbloccare l’interruttore di avvio/arresto e posizionarlo su
Страница 24 из 42 CARATTERISTICHE TECNICHE Molatrici rettilinee SG6/750 SG6/1000CE Potenza nominale W 750 1000 Velocità a vuoto 27000 12000-27000 min-1 Diametro max. mola/disco mm 25 25 Diametro pinza mm 6 6 Peso in funzione della EPTA-Procedure 01/2003 kg 1.4 1.5 Rispettare scrupolosamente le istruzioni contenute
Страница 25 из 42 Dura: Materiali morbidi, superfici rozze e spigoli, minor digrossamento e maggior durata, alta qualità du superficie. Fresa Metallo duro (B) Dentatura rozza: Acciaio inossidabile, acciai allegati, metalli leggeri. Dentatura fine: Acciai duri, acciai temperati. Mole di feltro (C) Abbisognano pasta
Страница 26 из 42 ALLGEMEINE SICHERHEITSBESTIMMUNGEN ACHTUNG! Es sind alle Anweisungen zu lesen. Bei Nichtbeachtung nachstehender Anweisungen kann es zu Stromschlägen, Bränden und/oder schweren Verletzungen kommen. Der Begriff „Elektrowerkzeug“ in allen untenstehenden Hinweisen bezieht sich auf die netz- (mit Kabel)
Страница 27 из 42 SPEZIELLE SICHERHEITSWARNUNGEN Gemeinsame Sicherheitshinweise zum Schleifen, Arbeiten mit Drahtbürsten, Polieren und Modellieren: Dieses Elektrowerkzeug ist zu verwenden als Schleifer, Modelliermaschine, Polierer und Drahtbürste. Beachten Sie alle Sicherheitshinweise, Anweisungen, Darstellungen und
Страница 28 из 42 unkontrolliertes Elektrowerkzeug gegen die Drehrichtung des Einsatzwerkzeugs an der Blockierstelle beschleunigt. Wenn z. B. eine Schleifscheibe im Werkstück hakt oder blockiert, kann sich die Kante der Schleifscheibe, die in das Werkstück eintaucht, verfangen und dadurch die Schleifscheibe
Страница 29 из 42 des Netzsteckers. Dadurch wird ein unkontrollierter Wiederanlauf verhindert. Sichern Sie das Werkstück. Ein mit Spannvorrichtungen oder Schraubstock festgehaltenes Werkstück ist sicherer gehalten als mit Ihrer Hand. KONFORMITÄTSERKLÄRUNG Wir erklären unter unserer eigenen Verantwortung, dass die in
Страница 30 из 42 TECHNISCHE DATEN Geradschleifer SG6/750 SG6/1000CE Aufnahmeleistung W 750 1000 Leerlaufgeschwindigkit 27000 12000-27000 min-1 Max. Durchmesser Schleifscheibe/Stein mm 25 25 Durchmesser Spannzange mm 6 6 Gewicht entsprechend EPTA-Procedure 01/2003 kg 1.4 1.5 Die in diesem Handbuch enthaltenen
Страница 31 из 42 SPEZIFIKATIONEN UND ANWENDUNGEN DER TAFEL 1 Schleifscheibe (A) Schleifmittel: Korondum: Für Kohlenstoff und legierte Stähle geeignet. Siliziumkarbid: Für Gusseisen, Leichtmetalle, Hartmetall, Baustoffe. Härte: Weich: Für harte Werkstoffe, glatte Oberflächen, stärkere Schrupparbeit und feine
Страница 32 из 42 ОБЩИЕ УКАЗАНИЯ ПО БЕЗОПАСНОСТИ ВНИМАНИЕ! Прочтите все предупреждения и указания мер безопасности и все инструкции. Невыполнение предупреждений и инструкций может привести к поражению электрическим током, пожару и (или) серьезным повреждениям. Сохраните все предупреждения и инструкции для того,
Страница 33 из 42 ровок, технического обслуживания, замены принадлежностей или помещением её на хранение. Подобные превентивные меры безопасности уменьшают риск случайного включения машин. d) Храните неработающую машину в месте, недоступном для детей, и не разрешайте лицам, не знакомым с машиной или данной
Страница 34 из 42 металлические части электроинструмента и приводить к удару электрическим током. Всегда крепко держите электроинструмент при запуске. При достижении полной скорости реактивный момент двигателя может привести к смещению электроинструмента. По возможности используйте для фиксации заготовки тиски.
Страница 35 из 42 спокойно и неподвижно до остановки круга. Никогда не пытайтесь вынуть еще вращающийся отрезной круг из разреза, так как это может привести к обратному удару. Установите и устраните причину заклинивания. Не включайте повторно электроинструмент, пока абразивный инструмент находится в заготовке. Дайте
Страница 36 из 42 ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ Машина ручная электрическая прямая шлифовальная SG6/750 SG6/1000CE Входная мощность Вт 750 1000 Скорость на холостом ходу 27000 12000-27000 мин-1 Максимальный диаметр шлифовального/точильного круга мм 25 25 Диаметр зажима мм 6 6 Вес согласно процедуре EPTA 01/2003 кг 1.4
Страница 37 из 42 сти. Электронный блок контроля скорости позволяет устанавливать предопределенный уровень скорости вращения вала двигателя и соответственную частоту ударов при отбойных работах. Двигатель вращается на скорости, которая устанавливается оператором в зависимости от типа выполняемой работы. Скорость
Страница 38 из 42 УТИЛИЗАЦИЯ Электроинструмент, отслуживший свой срок и не подлежащий восстановлению, должен утилизироваться согласно нормам, действующим в стране эксплуатации. В других обстоятельствах: – не выбрасывайте электроинструмент вместе с бытовым мусором; – рекомендуется обращаться в специализированные