![background image](/i/hotpoint-ariston/145105/hotpoint-ariston-hnp-65s-cd/h/hotpoint-ariston-hnp-65s-cd-036.png)
36
GB
PYRAMID controls
Models with mechanical keypad
HNP 6.5 CM X/HA
HYM 60 IX/HA
HPM 61 IX/HA
HRP 9.8 CM (OW)/HA
HRP 9.8 CM (AN)/HA
HRP 6.5 CM (OW)/HA
HRP 6.5 CM (AN)/HA
HRP 6.5S CM (OW)/HA
HRP 6.5S CM (AN)/HA
HNP6.5SCM(W)/HA
HNP6.5SCM(K)/HA
HNP9.5SCMX/HA
HNP6.5SCMX/HA
T1
T2
T3
T4
T5
T1 Motor reset
Pressing the button while the hood is in operation turns it
OFF.
T2 Speed 1
Pressing the button sets the hood to speed 1.
T3 Speed 2
Pressing the button sets the hood to speed 2.
T4 Speed 3
Pressing the button sets the hood to speed 3.
T5 Lights ON/OFF
Models with soft button keypad
HNP 9.8 AB X/HA
T1 Motor reset
Press the button with the hood off to set speed 1. Pressing
the button while the hood is in operation turns it OFF.
T2 Speed 1
Pressing the button sets the hood to speed 1.
T3 Speed 2
Pressing the button sets the hood to speed 2.
T4 Speed 3
Pressing the button sets the hood to speed 3.
T5 Booster
Pressing the button sets the hood to high speed. After 5
minutes, the hood returns to the previous speed; pressing
a speed button (
T2
,
T3
or
T4
) quits booster mode and sets
the selected speed.
T6 Lights ON/OFF
Grease/odour
fi
lter warnings
The
T2
icon
fl
ashes to indicate that the grease
fi
lter is
saturated, while
T3
fl
ashes to indicate that the odour
fi
lter
is saturated, and if both are
fl
ashing then both
fi
lters are
saturated. You must then clean/replace the grease
fi
lter (
A
)
or odour
fi
lter (
B
) or both, accordingly (see “Maintenance
and care”).
To reset the
fi
lter counter:
Hold down
T5
for three seconds while the hood is on.
The warning led
fl
ashes three times, then returns to its
normal mode If both
fi
lter warnings are active at the same
time, you must reset each separately.
The
fi
rst sequence resets the grease
fi
lter, while the second
sequence resets the odour
fi
lter.
Hood con
fi
guration:
To set the operating mode of the hood, hold down T5 for 6
seconds while the product is off. Icons T2 or T3 will light up
to show the type of installation: T2 ventilation, T3
fi
ltering.
You can change the type of installation by pressing T4
cyclically.
To save the new con
fi
guration press T1 individually.
Models with soft button keypad and display
HNP 6.5S CD X/HA
HPS 60 IX/HA
1 Motor ON/OFF
Press the button with the hood off to set speed 1. Pressing
the button while the hood is in operation turns it OFF.
T2 Speed -
Pressing the button returns the hood to the previous speed.
T3 Speed +
Pressing the button returns the hood to the next speed.
T4 Booster
Pressing this button sets the hood to high speed; the letter
"
b
"
fl
ashes slowly on the display. After 5 minutes, the hood
returns to its previous speed; this can also be done while
booster mode is on by pressing either speed button (
T2
or
T3
).
*
Only available in certain models
T1
T2
T3
T4
T5
B
T6
T1 T2 T3
T4 T5 T6
B
HNP94.5SCMX/HA