Руководство пользователя: световой пульт, контроллер DMX Involight DD6

Инструкция для Involight DD6

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

1 of 1 pages

6CH LCD DIMMER PACK WITH SHUCKO

Thanks for purchasing 6CH LCD dimmer pack. This controller is 6-channel
dimmer pack with shucko socket. It can work alone or used as a DMX pack, as
well controlled by analog signal. When it works stand alone, there are 12
built-in program can be chosen, the speed can be adjusted When work as DMX
pack, it can be controlled by 1 to 6 channels, by address is between 001 to 512.
When it is under analog signal, it can be controlled by 6 channels signal in DC
0-10V The dimming is various in SWITCH, LINEAR, SQUARE As well, it has
the function of pre-heating, circuit brake protection, phase compensation, DMX

M/S, etc…Before operation, please carefully read this manual first. Thanks!

Parameter

：

POWER SUPPLY----------------------------- SINGLE PHASE AC 220V 50-60HZ

3-PHASEAC 220V 50-60HZ

LOAD-------------------------------------------------------------------MAX

：

6*10A/CH

DMX OUTPUT------------------------------------------------3PIN female XLR socket

DMX INPUT-----------------------------------------------------3PIN male XLR socket

ANALOGUE INPUTS----------------------------------------DC 0-10V 8PIN D socket

DIMENSIONS------------------------------------------------------482mmX40mmX90mm

THE POWER SUPPLY ON-LINE DIAGRAM

：

SINGLE PHASE AC220V 50-60HZ

：

E L N

E E L3 L2 L1 N N N

3-PHASE AC220V 50-60HZ

：

E L3 L2 L1 N

E E L3 L2 L1 N N N

Оглавление инструкции

Страница 1 из 12
6CH LCD DIMMER PACK WITH SHUCKO Thanks for purchasing 6CH LCD dimmer pack. This controller is 6-channel dimmer pack with shucko socket. It can work alone or used as a DMX pack, as well controlled by analog signal. When it works stand alone, there are 12 built-in program can be chosen, the speed can
Страница 2 из 12
Operating instructions： 1,START MENU： Connect to switch on power supply, first the LCD shows the edition number and start the automatic check in alternate current, and then, The this time DMX instructions the light flash is slow. After completes. Enter to start menu. (Meet the plank show the
Страница 3 из 12
stop the channel’s value add. Reduce：While starting the menu, it is each to press once DOWN key all channels reduce 1, be some the channel reduces to 0 hours then stops the channel’s value reduces. Keep on pressing down over two second, then reduce quickly 1, be some a the channel reduces to 0
Страница 4 из 12
Dmx fail Prog08 The movable light marks the Place Position, below the type is together。 B. Press UP/DOWN once to circularly choose：Hold/ Analog/ Prog01-12。 [Hold]：The last-received DMX signal will be kept。 [Analog]：suffer the DC0-10V analogue input. When there is the DMX signal, analogue will
Страница 5 из 12
Press ESC to exit DMX FAIL second-class function menu, enter the first-class function menu. 3.2.2：PHA CORR Menu. A. Under the first-class function in PHA CORR menu, press MENU to enter the second-class function menu, it shows the current mutual compensation status; it runs Pha corr as following if
Страница 6 из 12
by one, can pass the Single function checking [Single]: Establishing address for single channel, it does not affect the other addresses. C. In the second-class function in DMX ADDR menu, press ESC to exit the second-class function menu, enter the first-class function menu. Press MENU to enter the
Страница 7 из 12
1, The second line shows the channel address, press and hold it more then two seconds, the channel sequence number quickly increases/decreases by 1, the second line will shows the relevant channel address accordingly. Channel sequence number circulates from Chan [1] to Chan[12]. Press MENU, the
Страница 8 из 12
channels, can pass the singled function checking. C. Under the second-class function PREHEATING menu, press ESC to exit second-class function menu, enter the first-class function menu。Press MENU to enter third-class function menu D. 1. Setup ALL for the third-class function in PREHEATING menu, If
Страница 9 из 12
the channel sequence number will adds/reduce 1 quickly, preheating value one the second line varies accordingly, the channel sequence number circulates from Chan[1] to Chan[12]. Press the key of MENU, the movable light mark transfer to the line of channel sequence number, then press the UP/DOWN
Страница 10 из 12
B. Press once UP/DOWN then circulates to choose b：Linear/Switch/Square。 [Linear]：The line adjusts the movable light. [Switch]：The switch type adjusts the movable light, 50% below for 0 output,50% is above to output with 100%. [Square]：The curve adjusts the movable light。 C. Press MENU/ESC withdraw
Страница 11 из 12
PROG08：100000、110000、111000、111100、111110、111111、 000000 PROG09：100001、110011、111111、110011、100001、000000 PROG10：100000、110000、111000、111100、111110、111111 111110、111100、111000、110000、100000、000000 PROG11：110000、001100、000011 PROG12：001100、010010、100001、000000 3．CONNECT THE LINE DIAGRAM： SINGLE
Страница 12 из 12

Инструкция для Involight DD6

Инструкции и руководства похожие на Involight DD6

Другие инструкции и руководства из категории световой пульт, контроллер DMX