3
SeRviCe engine
Soon Light
illuminates briefly when the ignition
is turned on. if it remains on or is blinking
after the engine is started, the on-board
diagnostics system (obD-ii) has detected
a malfunction. Drive in a moderate
fashion and contact your authorized
dealer as soon as possible.
4
PoweR tiLt/
teLeSCoPing
SteeRing CoLumn*
Your power tilt steering column has a
four-way rocker control that allows you
to adjust the steering wheel to your
desired position.
5
SteeRing wheeL
Audio ContRoLS*
Press
VOL +
or
VOL -
to increase or
decrease volume levels.
Press
to access the next/
previous radio station preset, CD
track or preset satellite radio channel*.
Press
to access voice recognition.
Press to access SYnC®
phone features.
6
Right vehiCLe
inFoRmAtion diSPLAy
Displays information about
entertainment, Phone, navigation*
and Climate. Use the right, 5-way
control located on your steering wheel
to scroll through, highlight and make
minor adjustments within a selected
menu. Refer to the
MyLincoln Touch™
chapter in your
Owner’s Manual
for
more information.
7
PuSh Button StARt
You can start your vehicle while your
keys remain in your pocket, purse
or back pack. With your vehicle in P
(Park), fully press the brake pedal and
press the
ENGINE START STOP
button.
Press the button again to turn the
engine off.
Note:
Your intelligent access key must
be inside the vehicle for the ignition
to start.
8
PuSh Button
ShiFt tRAnSmiSSion
Your vehicle is equipped with an
electronic transmission. The shift buttons
are located on the center stack next the
MyLincoln Touch™ system.
Putting your vehicle in gear:
1. Fully press down the brake pedal.
2. Press and release one of the
PRNDS
buttons to select your gear.
3. The gear shift button you select will
illuminate and the instrument cluster
will show a telltale of the selected gear.
4. Release the brake pedal and your
transmission will remain in the
selected gear.
Note:
When entering an automatic car
wash,
always
put your vehicle into
Stay
in Neutral
mode. To put your vehicle in
Stay in Neutral
mode, make sure your
vehicle is stationary first, and then:
1. Press the
N
(neutral) button on the
shifter assembly once. The information
display screen will read “Press
N
to
enter
Stay in Neutral
mode”.
2. Press
N
on the shifter assembly
again. The message
“Stay in Neutral
mode engaged”
will appear in the
instrument cluster and the n button
will flash continuously to confirm
your selection.
3. To exit
Stay in Neutral
, select another gear.
1
LeFt vehiCLe
inFoRmAtion diSPLAy
Provides information about various
systems on your vehicle. Use the left,
5-way control located on the steering
wheel to choose and confirm settings
and messages. Refer to the
Information
Displays
chapter in your
Owner’s Manual
for more information.
2
AdAPtive
CRuiSe ContRoL*
Automatically adjusts your speed to
maintain a set distance between you
and the vehicle in front of you in the
same lane. You can set the gap distance
between yourself and the vehicle in front
by pressing the and buttons on the
steering wheel.
Note:
Driving aids do not replace the
need to watch where the vehicle is
moving and brake where necessary.
Refer to your the
Cruise Control
chapter
of your
Owner’s Manual
for safety
information, more detail and limitations.
5
1
1
4
3
2
8
5
7
6
inSTRUMenT
PAneL
4
* if equipped
* if equipped
Preproduction model shown.
1090211_13_MKZ_QRG_LE_081412.indd 4-5
8/14/12 1:49 PM