2 01 4   N A V I G A T O R

10

11

Second-Row Heated Seats

 

The rear heated seat controls are 
on the rear of the center console.

 

Press 

 for maximum heat  

 

or 

 for minimum heat. 

 

Press again to switch off.

Note: 

The heated seats reset at 

every ignition run cycle. They will 
turn off automatically when you 
switch off the engine. 

Memory Seat Feature

 

The memory function will save 
and recall the positions of the 
driver seat, power mirrors, 
adjustable pedals and steering 
column. Use the control located 
on the side of the driver’s seat 

 

 to program and then 

recall saved memory positions.

To program position 

1

, switch the 

ignition on. Move the memory 
features to your preferred 
position. Press and hold the 

1

 button 

 for about two 

seconds until you hear a tone. 
Use this same procedure to set 
the second position by using the 

2

 button 

. You can now use 

these controls to recall the set 
memory positions.

Auto-Leveling Suspension* 

The system helps keep the rear 
of your vehicle at a constant 
level, thanks to a hydraulic pump 
inside of each rear shock. The 
feature helps improve ride, 
handling and general vehicle 
performance during certain road 
conditions, steering maneuvers, 
braking and acceleration, and 
towing. See the 

Driving Aids

 

section of your 

Owner's Manual

 

for details. 

Convenience

Autowipers

 

If you switch on this feature, your 
wipers will automatically turn on 
when moisture is present on the 
windshield. The wiper speed 
will vary based on the amount 
of moisture detected on the 
windshield and the sensitivity 
setting. The wipers will continue 
to wipe as long as moisture is 
detected. To deactivate, turn  
your wiper controls off. 

Note:

 Make sure you switch this 

feature off before entering a  
car wash. 

MyKey® 

MyKey allows you to program 
certain driving restrictions in 
order to promote good driving 
habits. You can set speed 
restrictions and limit volume 
levels. For complete information, 
refer to the 

MyKey

 chapter in 

your 

Owner’s Manual

. 

Power Liftgate

 

Press 

 on the instrument 

panel to open or close the power 
liftgate. For added convenience, 
there are three more ways  
to activate your power  
liftgate’s capabilities: 
1.   On your remote entry 

transmitter, press 

 twice 

within three seconds to open 
or close your power liftgate.

2.   To open using the liftgate 

control button in the liftgate 
handle: Unlock the doors 
using either the remote entry 
transmitter or the power door 
unlock control, and press  
the control.

3.   To close using the rear 

cargo area button: Press and 
release the 

 control 

located on the left rear 
quarter panel. This button is 
automatically disabled when 
the liftgate is latched. 

Note:

 Keep clear of the liftgate 

when operating the rear switch. 
Your power liftgate is equipped 
with an obstacle detection 
feature which will either stop or 
revert to a full open position if 
it encounters a solid object. For 
complete information, see the 

Liftgate

 section within the 

Locks

 

chapter of your 

Owner’s Manual

. 

Power-Adjustable  
Foot Pedals

 

Located to the left of your 
steering column, your power-
adjustable pedal control lets you 
move your brake and accelerator 
pedals closer. Press the   arrow 
to move the pedals closer to 
you or the   arrow to move 

the pedals further away from 
you. The pedals should only be 
adjusted when the vehicle is 
stopped and in park (P). 

SecuriCode

TM

 Keyless  

Entry Keypad

 

Lock or unlock the doors or 
release the liftgate glass without 
using a key. The keypad can be 
operated with the factory-set, 
5-digit entry code; this code is 
located on the owner’s wallet 
card in the glove box. You can 
also create up to five of your own 
5-digit personal entry codes. To 
lock all of the doors and liftgate, 
press and hold 

7•8

 and 

9•0

 at 

the same time. For complete 
information, refer to the 

Locks

 

chapter of your 

Owner’s Manual

.

*if equipped

Comfort

PowerFold® Third-Row Seat

*

 

60/40 split-folding bench seat 
uses a power-activated seatback 
release. Fold one side or both 
down for more flexibility.

The controls are located on  
the right-hand rear quarter trim  
panel that is accessible from  
the liftgate area.

Note: 

Make sure you unfasten all 

safety belts before lowering seats.

To lower:

1. 

 

Make sure that the head 
restraints are folded down first.

2.   Press  “

FOLD

” on the button.

3.   To return the seatback to its 

original position, press “

UP

”  

on the button.

Note: 

The power-folding seats  

will operate for 10 minutes after 
the ignition switch is turned off. 
The transmission must be in  
park (P) and the liftgate or  
liftgate glass must be open.

Front Climate Controlled Seats

 

Press the heated seat symbol 

 

or the cooled seat symbol 

 to 

cycle through the various settings 
and off. More indicator lights show 
warmer or cooler settings.