[Страница 6/12] - Инструкция: студийный монитор M-AUDIO SP-5B

Инструкция для M-AUDIO SP-5B

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

Installation

For optimal performance of the SP-5B, please read the following thoroughly and
carefully prior to installation.

Precautions

Handling: Please do not grab the speaker driver units: the SP-5B set is packaged
in the box tightly, so your attention is required when taking the speakers out of
the box. To avoid possible damage to the speaker units, hold both sides of the
speaker in order to pull them out of the box. The speaker units should not be
touched in order to avoid damage even after they are out of the box.

Connections: Connect the XLR balanced or TRS balanced / unbalanced input of
each SP-5B to the corresponding pre-amp, computer or game console outputs.
We recommend that you use high-quality balanced or unbalanced cables for
input connections. Also, turn off the power of the SP-5B and turn the Volume
Control of the SP-5B down to a minimum before making the necessary
connections.

Correct Power Operation: Since the SP-5B contains its own amplifier, it must
be connected to a power outlet using the detachable AC cable provided. Before
connecting power, please make sure that the Voltage-Select Switch, located on
the the speakers rear panel is set to the appropriate position, as described in the
rear-panel features list appearing earlier in this manual.

Note: - WARNING! - Use of improper voltage/selector-switch
combinations may result in hazardous conditions and/or damage
to speaker components not covered by speaker warranty.

XLR Balanced Connection

Assure that the power switch of the SP-5B is turned off and that the Volume
Control of the SP-5B is turned down to a minimum. Connect the male end of an
XLR balanced cable to the balanced input of the SP-5B (refer to the following
diagram for balanced connection).

TRS Balanced/Unbalanced Connection

Assure that the power switch of the SP-5B is turned to off and that the Volume
Control of the SP-5B is turned down to a minimum. Connect the male end of a
TRS balanced or unbalanced cable to the TRS input of the SP-5B (refer to the
following diagram for TRS connection).

Оглавление инструкции

Страница 1 из 13
Studiophile SP-5B Users Manual Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 What’s in the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Studiophile SP-5B
Страница 2 из 13
Introduction Thank you for choosing the SP-5B Studiophile Series pair of bi-amplified powered near field reference monitor speakers. M-Audio is well known for their digital audio interface technology, digital converters, audio pre amps and mixers. Now, after long research and development, the
Страница 3 из 13
2. Tweeter By employing a specially developed 1" silk dome with magnetic shielding, the tweeter can deliver distortion-free original sound and offer extremely natural sound. It minimizes reaction time by using fabric silk for excellent delivery, and also minimizes resonance by adapting a unique
Страница 4 из 13
Rear Panel: 1. XLR INPUT: This jack accepts XLR input connections, with either balanced or unbalanced wiring. The signal of the XLR INPUT is summed together with the TRS INPUT through a balanced input amplifier. So, either may be used as an input or mixed together. Input specifications apply to
Страница 5 из 13
3. PRODUCT LABEL: This label contains the model and serial number information. 4. VENT PORT: This port aids in reproduction of very low frequencies by discharging frequencies below 30 Hz.. 5. VOLUME CONTROL: Use the Volume Control to set the output sound pressure from the SP-5B to proper levels as
Страница 6 из 13
Installation For optimal performance of the SP-5B, please read the following thoroughly and carefully prior to installation. Precautions Handling: Please do not grab the speaker driver units: the SP-5B set is packaged in the box tightly, so your attention is required when taking the speakers out of
Страница 7 из 13
1 2 e lum Vo 2 3 1 1 2 S TR 3 XL R Inpu XL t R Inpu XL 1 2 Vo e lum t TR R S 1 2 3 wer Po N IOOCK T SH U TRICEN A ELECT OP NO CK OF DO RIS ! 3 wer Po N IOOCK T SH U TRICEN A ELECT OP NO CK OF DO 1 o wer Po RIS ! l.• ba Un ms k oh W• l./10 0mV• er: 30 Ba w ms ty: 20p. Po k oh itivi Am p: 20t Sens /
Страница 8 из 13
Placing the SP-5Bs Placing the speakers is one of the most important procedures in order to monitor sound accurately. To monitor with the SP-5Bs at their maximum capability, an appropriate listening environment and correct placement is required. Please, refer to the following in order to place the
Страница 9 из 13
3. Place the SP-5Bs vertically. Placing the SP-5Bs horizontally is not recommended. Remarks: DO NOT place any obstacles that may block the flow of air in front or between the SP-5Bs (which are a medium of sound, or create reflected sound, especially materials of high reflective tendencies including
Страница 10 из 13
Appendix A - Technical Specs Type: 2-Way Near Field LF Driver: 5 1/4" magnetically-shield mineral-filled polypropylene curved cone with high temperature voice coil and damped rubber surround HF Driver: 1" magnetically-shield natural Silk Dome Frequency Response: 33Hz - 22kHz Crossover Frequency:
Страница 11 из 13
Appendix B - Block Diagram 11
Страница 12 из 13
One Year Warranty MIDIMAN warrants that this product is free of defects in materials and workmanship under normal use for a period of one year from purchase date, so long as the product is: owned by the original purchaser; the original purchaser has proof of purchase from an authorized MIDIMAN
Страница 13 из 13

Инструкция для M-AUDIO SP-5B

Инструкции и руководства похожие на M-AUDIO SP-5B

Другие инструкции и руководства из категории студийный монитор