[Страница 6/6] - Руководство пользователя: весы MyWeigh PALMSCALE 8

Инструкция для MyWeigh PALMSCALE 8

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

Remember: You can permanently damage the scale and void your warranty by
overloading it!

Negative Value

Any tared value or a value left in memory will be removed from the tray. Press

or cycle

the power to re-Zero the unit.

NOTE: The display will show

If a negative weight is lower than the negative

range of the scale.

TROUBLESHOOTING & OPERATION NOTES:

1) If the Display ever becomes locked on "unSt", this indicates that the scale is unstable, please
place it on a stable surface to use. If the Display ever becomes

locked on

this indicates that the following:

A) The weight on the pan is out of the range of Zero. please remove the weight then power OFF.

B) The scale was shocked, dropped or otherwise damaged and the delicate weighing sensors
have been damaged. You can try recalibrating the scale (If the sensor has not been hurt too badly
it will work again after recalibration). Otherwise you will have to follow the warranty
instructions that came with your scale.

2) If the display is faint or the scale won't power on, This often indicates low batteries. If new
batteries do not fix this error the scale will have to be sent to us for replacement under our
Warranty.

For more information or more troubleshooting visit

WWW.MYWEIGH.COM

Оглавление инструкции

Страница 1 из 7
Palmscale® 8.0 User Manual Precautions Before Using The Scale The scale should always be used in an environment which is free from excessive air currents, corrosives. vibration, and temperature or humidity extremes. These factors will affect 5he displayed weight reading. Please check
Страница 2 из 7
Turn on The Scale Press to turn on the scale. The scale will go through a quick warm up procedure. then be ready for use. Display Window Current reading is stable. Scale is in TARE made. Scale is in ZERO made. Battery is at low voltage. Minus The weight can't be displayed "OVER LOAD" The weight is
Страница 3 из 7
tare indicator will appear and the display will show "0". Auto Power Off setting key Mode Press and release the key once to change weight unit. The PS7-700/800/1000 reads in g(grams), oz(ounces), 1/4oz, 1/8oz, ozt (tray ounces), dwt(pennyweight), or cf (carats). The PS7-200/300 reads in g. 1/4oz,
Страница 4 из 7
a) Release the battery cover by sliding out-wards. b) Place batteries into the battery compartment aligned correctly. When replacing batteries, use a tool if necessary to help facilitate their removal and replacement. c) Replace battery cover. 3) The scale is now ready for battery operation. AUTO
Страница 5 из 7
4) Press and Hold the key until the cal-weight reading flashes on the screen (ie 200.00 for PS7-200/300. 500.0 for PS7-700/800/1000). Then release. 5) The display will show "PASS". Calibration is complete. After a few seconds, the scale will return to normal weighing mode. Remove the weight from
Страница 6 из 7
Remember: You can permanently damage the scale and void your warranty by overloading it! Negative Value Any tared value or a value left in memory will be removed from the tray. Press the power to re-Zero the unit. NOTE: The display will show range of the scale. or cycle If a negative weight is
Страница 7 из 7

Инструкция для MyWeigh PALMSCALE 8

Инструкции и руководства похожие на MyWeigh PALMSCALE 8

Другие инструкции и руководства из категории весы