Parts identification

Before use

To make kubbe

Jamming

© Switch(es)

© Locking knob

 

© Motor housing

 

© Opening

 

© Food pusher

 

© Hopper plate

 

© Head

 

© Feed screw

 

© Cutting blade

 

©~© Attachments

© Cutting plate (fine)

© Cutting plate (medium)

 

© Cutting plate (coarse)

 

(m) Kubbe attachment A

 

@ Kubbe attachment B

 

@ Cap

Cautions

Unplug when assembling or disassembling the unit.

Close  supervision  is  necessary  when  any  appli­
ance is used near children.

When carrying the unit, be sure to hold Motor Housing

 

with both hands, not to hold only Hopper Plate.

Do  not  fix  Cutting  Blade  and  Cutting  Plate  when

 

using Kubbe Attachments.

Never feed food with hand. Use Food Pusher.

Do not grind hard foods such as bones and nuts.

Do not grind ginger and other materials with hard fiber.

To  avoid  jamming,  do  not  force  to  operate  the

 

unit with excessive pressure.

If  the  unit  jams  due  to  hard  materials  lodged  on

 

to  Feed  Screw  or  Cutting  Blade,  switch  off  imme­
diately and clean the unit.

(See "Jamming" on page 4.")

When the circuit breaker activates, do not switch on.

Never  try  to  undo  the  parts  or  to  repair  the  unit

 

by yourself.

This product is intended for household use only.

Make  sure  that  the  voltage  and  frequency  indi­
cated  on  the  bottom  plate  are  the  same  as  your

 

local supply.

Wash all the parts (except those that do not

 

touch foods ©,©,(^and ©) in warm soapy

 

water.

Before plugging in, ensure Switch is off.

To mince meat

(Assembling)

I  1  I  Place  Head  tightly  onto  Opening  of  Motor

 

Housing.  Holding  Head  with  one  hand,  place

 

Locking  Knob  into  the  hole  on  the  side  of  Motor

 

Housing and tighten it clockwise.

Place  Feed  Screw  into  Head,  long  end  first,  by

 

turning Feed Screw slightly until it is set into Motor

 

Housing.

Place  Cutting  Blade  onto  Feed  Screw  shaft  with

 

the blade facing the front as illustrated.

•  If  it  is  not  fitted  properly,  meat  will  not  be

 

ground.

4 

Place desired Cutting Plate next to Cutting Blade,

 

fitting protrusions in the slots.

Screw Cap into place until tight.
• Do not over tighten.

Place Hopper Plate on Head and fix into position.

Locate the unit on a firm place.
•  The  air  passage  at  the  bottom  and  the  side  of

 

Motor  Housing  should  be  kept  free  and  not

 

blocked.

(Mincing meat)

Cut all foods into pieces so that they fit easily into

 

Hopper opening.

Plug in, then switch on.

0 Feed foods into Hopper Plate.

 

— • Use Food Pusher.

—Recipe—

(Stuffing)

100 g
1 1/2 tablespoons

 

1 1 / 2  tablespoons

 

1/3 teaspoon

 

1/2 teaspoon

 

1 1 / 2  tablespoons

mutton

 

olive oil
onion (cut finely)
all spice
salt
flour

Mince mutton once or twice.

Fry onion until brown and add minced mutton, all

 

spice, salt and flour.

(Outer cover)

 

450 g

150  -  200  g

 

1  teaspoon

 

1

a pinch

 

dash

lean meat

 

flour

 

all spice

 

nutmeg
powdered red pepper

 

pepper

Mince meat three times and mix all ingredients

 

together in a bowl.
• More meat and less flour for outer cover creates

 

better consistency and taste.

Grind the mixture three times.

Disassemble by reversing the steps from [^] - [3j to

 

remove Cutting Plate and Cutting Blade.

I 7 I 

Place Kubbe Attachments A and B onto Feed

 

Screw shaft together, fitting protrusions in the slots.

8 

Screw Cap into place until tight.

 

• Do not over tighten.

9 

Following the same steps as in 15j - ( 6 j ,  make the

 

cylindrical outer cover.

Form kubbe as illustrated below and deep fry.

m   r—di

d::>

# %

When  the  circuit  breaker  automatically  stops  the

 

motor,  or  when  the  motor  continues  to  function

 

but  no  meat  comes  out  of  Cutting  Plate,  due  to

 

jamming of bone or other materials, switch off.

• Do not switch on.

Clean the unit. (See "To clean" below.)

To clean

(Disassembling)

Make  sure  that  the  motor  has  stopped  completely.

 

Disconnect the plug from the power outlet.

Disassemble by reversing the steps from S - [U .

10 

Cap has pins for easy unscrewing.

To remove Cutting Plate easily,

[Tl] place a screwdriver between Cutting Plate and

 

— Head as illustrated and lift up.

(Cleaning)

Remove meat, etc.

Wash each part in warm soapy water.

• A bleaching solution containing chlorine will dis­

color aluminum surfaces.

• Do not immerse Motor Housing in water, but only

 

wipe it with a damp cloth.

• Thinners and benzines will crack or change the

 

color of the unit.

A little salad oil on ® ~ © after washing and drying

 

will keep them lubricated.

Caution:
Do not wash washable parts in a dishwasher.

After use, switch off and unplug.

-3-

-4-