Инструкция для BMW K1100RS (1999), K1100LT (1999)

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

34.16

[ABS II] Bleeding pressure modulator

Remove the left battery cover.

Connect a vessel to the brake caliper bleed 
screws to trap escaping brake fluid, then open 
the bleed screw by half a turn.

Maintain pressue at the handbrake lever and 
open the bleed screw, at the same time pulling 
the hand brake lever in firmly.

e

 Caution:

Do not release the handbrake lever until the bleed 
screw has been closed.

Allow the brake fluid to emerge from both brake 
calipers until it is clear and free from bubbles.

Close the bleed screw while keeping the hand 
brake lever pulled in.

Bleeding the handlebar fitting

Remove combined switch (1) from the right han-
dlebar fitting.

Remove clamping screw from handlebar fitting.

Turn the brake flulid reservoir up round the han-
dle bar (arrow) until the air escapes from the 
brake line.

Turn the reservoir back down.

Tighten the clamping screw on the handlebar fit 
ting.

L

 Note:

When adding brake fluid, note the thickness of the 
brake pads. Add brake fluid up to the -MAX“ mark if 
the pads are new.

Add brake fluide.

L

 Note:

When checking front brake fluid level, the brake fluid 
reservoir must always be in a horizontal posi tion.

Replace the diaphragm and reservoir cover in po 
sition.

Tighten the retaining screws without using force.

Check brake operation.

Install the combined switch.

Bleeding rear brake

Bleeding brake caliper

The rear brake caliper does not have to be remo 
ved, nor the pistions pressed back.

The remaining procedure is the same as when 
bleeding the front brake circuit.

X

 Tightening torque:

Brake caliper to rear wheel drive .................. 40 Nm

[ABS II] Bleeding pressure modulator

Follow the same procedure as when bleeding the 
front brake circuit.

L

 Note:

When adding brake fluid, note brake pad thickness. 
Add brake fluid up to the „MAX“ mark with new pads.

Add brake fluid.

Replace the diaphragm and reservoir cover in 
position.

Check that the brake is operating correctly.

LT340310

1

LT340260

MAX

MIN

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
Оглавление инструкции

Document Outline