Страница 2 из 12 Two Sections Linear Beam Bar, CREE 4-in-1 10W User Manual Please read the manual before operation A. SPECIFICATION 1. Power input: AC 100V-240V, 60Hz/50Hz 2. Wattage: 110W 3. LEDs: 8*10W CREE 4-in-1 4. Beam angle: 3 degrees 5. Selectable 1,36, 40 DMX channels 6. Weight: 8.7 kg 7. Size:
Страница 3 из 12 1. Auto running When the display shows: The light will run as the program which had been set. Press “SETUP” button to enter into the optional menu. Press “UP” and DOWN” to choose the optional which need to set the parameter as below : 1) LED function
Страница 4 из 12 When choose “led”, and press “SETUP” enter to LED auto running parameter setting. The option with black marks is selected. You could choose e-Auto（LED auto running ）or e-Manul (manual adjust the LED) When choose “e-Auto”, press “SETUP” button enter the menu Press “UP” and “DOWN” to select the
Страница 5 из 12 Press “SETUP” to enter the build-in programs. There are 10 programs inside. Press “UP” and “DOWN” to choose the built-in program from Show1 –Show10(the built-in program is pre-set and can not be reset) 3. Sound-active Mode When display shows this menu, enter the sound-active mode. Press “SETUP”
Страница 6 из 12 100-109 Built-in program Show9 110-119 Built-in program Show10 120-139 LED close, electronic machine return to the horizontal position 140-255 Sound active, the sensitivity will be higher when the value is larger. DMX Mode 2: 36-ch 36-ch Channel Value Function 1 0--180 Left BAR 0-180°(90°
Страница 7 из 12 33 0-255 LED8 R 0-100% 34 0-255 LED8 G 0-100% 35 0-255 LED8 B 0-100% 36 0-255 LED8 W 0-100% DMX Mode 3: 40-ch 40channel mode Channel Value Function 1 0--180 Left BAR 0-180°(90°horizontal) 180-255 Left BAR 180° 0-255 Left BAR speed, the speed is faster when the No. is larger. 0-180 Right BAR
Страница 8 из 12 12 0-255 LED1 W 0-100% 13 0-255 LED2 R 0-100% 14 0-255 LED2 G 0-100% 15 0-255 LED2 B 0-100% 16 0-255 LED2 W 0-100% 17 0-255 LED3 R 0-100% 18 0-255 LED3 G 0-100% 19 0-255 LED3 B 0-100% 20 0-255 LED3 W 0-100% 21 0-255 LED4 R 0-100% 22 0-255 LED4 G 0-100% 23 0-255 LED4 B 0-100% 24 0-255 LED4 W 0-100%
Страница 9 из 12 As the above picture, if you choose 10s. After you restore factory settings, the time will keep 10s. Choose the “Adjust”, press the “SETUP” to set the position of electronic motor. When it shows 90°but the bar is not in horizontal position, you could adjust it through this function. It will be ok
Страница 10 из 12 G. Restore factory setting Operate in the setup menu, please refer to the operation Press “MODE”, “SETUP” at the same time, then power on. When the LCD prompts the process as below, release the button and restore factory settings.
Страница 11 из 12 ООО «ИНВАСК» Адрес: 143406, Московская область, Красногорск, ул. Ленина, дом 3-Б Тел. (495) 565-0161 (многоканальный) Факс (495) 565-0161, доб. 105 http://www.invask.ru e-mail: invask@invask.ru Сервис-центр «ИНВАСК» Адрес: 143400, Московская область, Красногорск, Коммунальный квартал, дом. 20 Тел.
