Colorfull Water tank 
Water   tank   can  change   the  color  against  the   different   soleplate  
temperature .There are five different water tank:Setting “0” blue setting 1 
green，setting 2 orange；III setting，purple；MAX setting  red.[Fig.7]

Renewable  anti-calc  system 
A special resin filter inside the water reservoir softens the water and prevents 
scale build-up in the plate. The anti-calc system can be changable，clockwise 
the anti-calc box out by using the icon or similar equipment,and couterwise the 
anti-calc box in by using the icon or similar equipment too. 

[Fig. 9]

Please note:
Use  tap  water only. Distilled and/demineralised water makes the anti-calc 
system ineffective by altering its physicochemical characteristics.
Do  not  use  chemical additives, scented substances or decalcifiers. Failure 
to  comply  with  the  above-mentioned  regulations  leads  to  the  loss of 
guarantee.

Anti-drip system
With  the  anti-drip  system,  you can perfectly iron even the most delicate 
fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to 
the  point  where  no  more  steam  comes out, but rather drops of boiling 
water  that can  leave marks or stains. In these cases, the Anti-drip system 
automatically  activates  to  prevent  vaporization, so that you can iron the 
most delicate fabrics without risk of spoiling or staining them.

Automatic shut off
The automatic shut off device trips after the iron has been left for approx. 
eight  minutes in the upright position or unused for approx. Thirty seconds in 
the  horizontal position. The light comes on to indicate that shut off has 
tripped.  As  soon  as  you move the iron, the device turns off and the iron 
starts working again.

General Instructions
When using the iron for the first time, you may notice a slight emission of 
smoke and hear some sounds made by the expanding plastics. This is quite 
normal  and it  stops  after  a  short time. We also recommend passing the 
iron over an ordinary cloth before using it for the first time.

GARMENT

 LABEL

FABRIC 

TYPE

THERMOSTAT 

REGULATION

synthetic

silk - wool

Cotton - linen

•

low temperature

••

medium temperature

Fabric not to be ironed

•••

high temperature

Preparations
Soft the laundry to be ironed according to the international symbols on the 
garment label, or if this is missing, according to the type of fabric.

Start ironing the garments requiring a low temperature.
This  reduces  the  waiting  times  (the  iron  takes  less  time  to  heat  up  than  to 
cool down) and eliminates the risk of scorching the fabric.

Steam ironing

Filling the reservoir
1.  

Check that the plug is disconnected from the socket.

2.   Move the steam selector H to “     ” [Fig. 5].
3.   Open the lid B.
4.   Raise  the  tip  of the iron to help the water enter the opening without
     overflowing [Fig. 1]. 
5.   Slowly  pour  the  water into the reservoir using the special measure M
     and  taking  care  not  to  go  over  the  maximum level (about 400ml)
     indicated by “MAX” on the reservoir.    
6.   Close the lid B.

Selecting the temperature.
1.   Put the iron in a vertical position.
2.   Put the plug in the socket.
3.   Adjust  the thermostat knob I according to the international symbol on
     the  garment  label  [Fig. 3].  The  plate  temperature  control  light E
     indicates  that  the  iron is heating up. Wait until the plate temperature
     control light goes off before ironing.

Warning:   during ironing,  the plate temperature control light E comes on at 
intervals, indicating  that  the selected temperature is maintained. If you 
lower  the  thermostat temperature after ironing at a high temperature, do not 
start ironing until the plate temperature control light comes on again.

P/3

P/4