4
XENYX Q1202USB/Q1002USB/Q802USB/Q502USB User Manual
1. Introduction
XENYX Mic Preamps
The microphone channels feature high-end XENYX Mic Preamps that
compare well with costly outboard preamps in terms of sound quality
and dynamics and boast the following features:
•
130 dB dynamic range for an incredible amount of headroom
•
A bandwidth ranging from below 10 Hz to over 200 kHz for crystal-clear
reproduction of even the finest nuances
•
The extremely low-noise and distortion-free circuitry guarantees absolutely
natural and transparent signal reproduction
•
They are perfectly matched to every conceivable microphone with up to
60 dB gain and +48 volt phantom power supply
•
They enable you to use the greatly extended dynamic range of your
24-bit/192-kHz HD recorder to the fullest, thereby maintaining optimal
audio quality
“British EQ”
The equalizers used for the XENYX Series are based on the legendary circuitry of
top-notch consoles made in Britain, which are renowned throughout the world
for their incredibly warm and musical sound character. Even with extreme gain
settings these equalizers ensure outstanding audio properties.
!
!
Caution!
◊
We should like to draw your attention to the fact that extreme volumes
may damage your hearing and/or your headphones or loudspeakers.
Turn the MAIN MIX control and PHONES control in the main section fully
counter-clockwise before you switch on the unit. Always be careful to
set appropriate volume levels.
Important notes concerning installation
◊
The sound quality may diminish within the range of powerful
broadcasting stations and high-frequency sources. Increase the
distance between the transmitter and the device and use shielded
cables for all connections.
1.1 General mixing console functions
A mixing console fulfils three main functions:
•
Signal processing
: Preamplification, level adjustment, mixing of effects,
frequency equalization.
•
Signal distribution
: Summing of signals to the aux sends for effects
processing and monitor mix, distribution to one or several recording tracks,
power amp(s), control room and 2-track outputs.
•
Mix
: Setting the volume level, frequency distribution and positioning of the
individual signals in the stereo field, level control of the total mix to match
the recording devices/crossover/power amplifier(s). All other mixer functions
can be included in this main function.
The interface of BEHRINGER mixing consoles is optimized for these tasks enabling
you to easily keep track of the signal path.
1.2 Before you get started
1.2.1 Shipment
Your mixing console was carefully packed in the factory to guarantee safe
transport. Nevertheless, we recommend that you carefully examine the
packaging and its contents for any signs of physical damage, which may have
occurred during transit.
◊
If the unit is damaged, please do NOT return it to us, but notify your
dealer and the shipping company immediately, otherwise claims for
damage or replacement may not be granted.
1.2.2 Initial operation
Be sure that there is enough space around the unit for cooling purposes and to
avoid over-heating please do not place your mixing console on high-temperature
devices such as radiators or power amps. The console is connected to the
mains via the supplied cable. The console meets the required safety standards.
Blown fuses must only be replaced by fuses of the same type and rating.
◊
Never connect the XENYX to the power supply unit when the latter is
connected to the mains! First connect the power supply unit to the
console, then connect the power supply unit to the mains.
◊
Please note that all units must be properly grounded. For your own
safety, you should never remove any ground connectors from electrical
devices or power cables, or render them inoperative.
◊
Please ensure that only qualified people install and operate the
mixing console. During installation and operation, the user must have
sufficient electrical contact to earth, otherwise electrostatic discharges
might affect the operation of the unit.
1.2.3 Online registration
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contact
the BEHRINGER retailer from whom the equipment was purchased. Should your
BEHRINGER dealer not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information is included in the
original equipment packaging (Global Contact Information/European Contact
Information). Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area of our website
(http://behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and efficiently.
Thank you for your cooperation!
