4

Switch back to the upper holes as soon as the shoulder straps do no longer fit over the child´s 

shoulders.

7. REMOVING THE HEADHUGGER AND SHOULDER PADS

a)  Remove the headhugger as soon as the headhugger does no longer fit over the child´s 

shoulders.

b)  Remove the velcros of the headhugger on the top left and right side on the back of the 

seat cover. Release the loops at the end of the shoulder straps from the triangle in the belt 

system, situated at the bottom of the backrest under the seat cover.

– Completely pull the shoulder straps out of the holes in the backrest.

c)  pull the shoulder straps through the shoulder pads and the headhugger. make sure to 

feed the straps back through the holes in the backrest mechanism and attach them to the 

triangle.

You can use the haedhugger and the shoulder pads separately.

8. ATTACHING THE BUMPER BAR

a)  Slide in latches on left and right side into gadgets sewn into the seat fabric.

b)  press buttons on left and right end of the bumper bar to take it off.

9. RECLINING THE LEG REST

a)  press the leg rest on both front edges and push down.

b)  Simply lift the leg rest to put it back to the starting position.

10. RECLINING THE BACKREST

a)  pull the recline lever on the back of the seat to recline the backrest.

b)  to raise it again just lift the backrest of the seat. the backrest can be engaged in 5 different 

positions.

a)  b) push button underneath the handle bar and slide up upper part of handle bar to extend 

it until it clicks in place. Shorten the handle bar by pushing the button again.

11. ADjUSTING HEIGHT OF THE HANDLE

– Remove all contents from the basket. if attached, ensure the canopy is folded back.

a)  lift the central lever located at the back of the shopping basket.

b)  push down the lock lever (extended bar on the right side of the locking system).

c)  d) press the button at the handle bar and fold the buggy by pushing it slightly forward. 

please note: Keep the button pushed the whole time.

 to make folding easier lift 

the locking lever with your foot. Fold the buggy together carefully until the safety clip is 

securely locked.

12. FOLDING THE STROLLER

– pull the flexible carring handle on right rear tube and lift the stroller.

13. CARRYING THE STROLLER

14. REMOVING THE SEAT COVER

– Slightly fold the stroller to reduce tension. 

– Remove the canopy from the stroller, if attached.

a)  take the seat cover’s hooks (3) off the frame on left and right side

– open the press buttons (4) of the straps connected to the seat side panels and the basket 

rear tube.

– open the flaps (5) which are fixed with velcro over the tubes, one on each side.

– Feed the strap with the slider (6) of the central harness buckle through the hole in the seat 

fabric. 

b)  Feed the loops on the end of the shoulder straps through the triangle in the backrest (7).

c)  Feed the shoulder straps through the holes in the seat fabric (8).

– open the press buttons which are on the left and the right side from the seat on the bottom 

from the fabric.

– pull the seat cover over the belt shifting button on the seat.

– Slide the fabrics from the seat base tubes.

– Reverse this procedure to refit the seat cover and the harness. make sure that the seat 

tubes slide back into the pockets inside the seat cover.

a)  attach the canopy adaptor on to the inside of the frame tubes of the buggy.

b)  to remove the canopy reverse procedure.

c)  d) e) Extend the canopy and place canopy rear flap behind the seat.

f) 

lie-flat position: put the rear flap over the seat’s back rest and fixate it with the two velcros 

underneath.

g)  h) i) the canopy is adjustable to various positions. the Canopy has a height adjustment 

and a forward rotation function. to rotate open the zip located at the top of the canopy.

the canopy has a fully ratcheting function to create complete coverage. Simply pull on the 

front of the canopy to the desired position. the height can be easily adjusted by simply sliding 

the canopy up or down the frame. the entire canopy can also be tilted forward. For maximum 

coverage, unzip the extra panel on top of canopy and pull forward.

j)  the canopy flap at the rear of the stroller can be rolled up and fixed with a velcro fastener, 

if required.

15. ATTACHING THE CANOPY

– Remove the canopy

a)  undo the press buttons that attach the seatcover with the rear frame.

b)  unhook the side panels at the left and right upper end out of the adaptor. 

c)  open the adaptor on the left and the right side under the seat unit.

d)  pull out the complete sub seat towards the front of the buggy.

e)  to attach the subseat reverse this procedure. Ensure that the buggy is not completely 

unfolded.

16. TO REMOVE THE COMPLETE SUB SEAT

6. ADjUSTING THE HARNESS SYSTEM FOR NEWBORNS

– Release the loops at the end of the shoulder straps from the triangle in the belt system, 

situated at the bottom of the backrest under the seat cover.

– Completely pull the shoulder straps out of the holes in the backrest.

– Feed the shoulder straps through the two bottom holes. make sure to feed the straps back 

through the holes in the backrest mechanism and re-attach them to the triangle.

– to adjust the length of the shoulder straps to newborns please attach the inner loop of the 

shoulder strap ends to the triangular ring.

e)  the brake can be used even with a folded buggy. with a locked brake the folded buggy 

can rest against a wall to prevent inadvertent rolling.