14
English
SPECIFICATIONS
Model
CS30Y
CS35Y
CS40Y
CS45Y
Guide bar length (Max. cutting length)
300 mm
350 mm
400 mm
450 mm
Guide bar Type
P012-50CR
P014-50CR
P016-50CR
P0H18-50CR
Voltage (by areas)*
1
(110 V, 220 V, 230 V, 240 V)
Power Input*
1
110 V: 1560 W
220 V, 230 V, 240 V: 2000 W
No-load chain speed
14.5 m/s
Type of chain
91PX-45
(Oregon)
91PX-52
(Oregon)
91PX-57
(Oregon)
91PX-64
(Oregon)
Chain pitch/Gauge
9.53 mm (3/8") / 1.27 mm (0.05")
Sprocket
Number of teeth: 6
Oil pump
Automatic
Chain oil tank capacity
150 ml
Overload protection
Electrical
Chain brake
Manually actuated
Weight*
2
5.2 kg
5.4 kg
5.4 kg
5.5 kg
*
1
Be sure to check the nameplate on product as it is subject to change by areas.
*
2
Weight: According to EPTA-Procedure 01/2003
STANDARD
ACCESSORIES
(1) Chain case .................................................................. 1
(2) Guide bar ..................................................................... 1
(3) Chain ........................................................................... 1
(4) Plug clip*...................................................................... 1
* Not supplied in certain sales areas.
Standard accessories are subject to change without notice.
OPTIONAL
ACCESSORIES
(sold
separately)
(1) Chain Saw Oil
(2) Round File
(3) Depth Gauge Jointer
Round File and Depth Gauge Jointer are to be used
for sharpening of chain blades. As to its application,
please refer to the item titled “Sharpening of the Chain
Blade”.
(4) Chain Case
Always keep the chain cover on the chain while carrying
the chain saw or while storing it.
Optional accessories are subject to change without notice.
APPLICATIONS
◯
General wood cutting.
PRIOR
TO
OPERATION
1.
Power
source
Ensure that the power source to be utilized conforms
to the power requirements speci
fi
ed on the product
nameplate.
2.
Power
switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3.
Extension
cord
When the work area is remote from the power source,
use an extension cord of su
ffi
cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4.
Con
fi
rm
the
chain
tension
Improper chain tension may result in damage to the
chain and the guide bar, and could cause a serious
accident. Always con
fi
rm that there is proper tension on
the chain prior to operation.
5.
Fill
the
oil
tank
with
oil
This unit is shipped without oil in the oil tank.
Prior to operation, remove the oil cap and
fi
ll the tank
with accessory oil.
This unit is shipped without oil in the oil tank.
Prior to operation, remove the oil cap and
fi
ll the tank
with chain saw oil (sold separately), or SAE 20 or 30
motor oil. Do not use stained or degraded motor oil.
Check oil reservoir periodically and keep it
fi
lled while
running saw.
6.
It is recommended to use an earth-leakage circuit
breaker or a residual current device.
SAW
CHAIN
AND
GUIDE
BAR
ASSEMBLY
WARNING
◯
Don’t use the saw chain or the guide bar other than
those speci
fi
ed in “SPECIFICATIONS”.
◯
Make sure the switch is turned o
ff
and the plug
disconnected from the socket.
◯
Always wear gloves when handling the saw chain.
◯
The tightening tension for the special nut has been
adjusted to the optimal level. Do not loosen it or tighten
it under any circumstances.
1.
Removing
the
Saw
Chain
(1) Check to make sure the chain brake has been released
before removing the side cover. (
Fig.
2
)
(2) Loosen the knob slightly and then loosen the tension
dial to release the tension on the saw chain. (
Fig.
3
)
(3) Completely loosen the knob and gently remove the side
cover.
(4) Gently remove the guide bar and saw chain.