GB

7

Front

Hooking position 

Back

for top 

H=40mm

!

 Use the hooks contained in the “accessory pack”.

•  Where  the  hob  is  not  installed  over  a  built-in  oven,  a 

wooden panel must be installed as insulation. This must 

be placed at a minimum distance of 20 mm from the lower 

part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet 

must be removed. It is advisable to install the oven so that it 

rests on two strips of wood, or on a completely flat surface 

with an opening of at least 45 x 560 mm (see diagrams).

560 mm

.

45 mm.

!

 The hob can only be installed above built-in ovens with a 

cooling ventilation system.

Electrical connection

Hobs equipped with a three-pole power supply cable are 

designed to operate with alternating current at the voltage 

and frequency indicated on the data plate (this is located 

on the lower part of the appliance). The earth wire in the 

cable has a green and yellow cover. If the appliance is to 

be installed above a built-in electric oven, the electrical 

connection of the hob and the oven must be carried out 

separately, both for electrical safety purposes and to make 

extracting the oven easier. 

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load 

indicated on the data plate. 

The appliance must be directly connected to the mains 

using an omnipolar circuit-breaker with a minimum contact 

opening of 3 mm installed between the appliance and the 

mains.  The circuit-breaker must be suitable for the charge 

indicated and must comply with current electrical regulations 

(the earthing wire must not be interrupted by the circuit-

breaker). The supply cable must not come into contact with 

surfaces with temperatures higher than 50°C.

!

 The installer must ensure that the correct electrical 

connection has been made and that it is compliant with 

safety regulations.

Before connecting to the power supply, make sure that:

•  The appliance is earthed and the plug is compliant with 

the law.

•  The socket can withstand the maximum power of the 

appliance, which is indicated on the data plate.

•  The voltage is in the range between the values indicated 

on the data plate.

•  The socket is compatible with the plug of the appliance. 

If the socket is incompatible with the plug, ask an 

authorised technician to replace it. Do not use extension 

cords or multiple sockets.

!

 Once the appliance has been installed, the power supply 

cable and the electrical socket must be easily accessible.

!

 The cable must not be bent or compressed.

!

 The cable must be checked regularly and replaced by 

authorised technicians only (see Assistance).

!

 The manufacturer declines any liability should these safety 

measures not be observed.

Gas connection

The appliance should be connected to the main gas supply 

or to a gas cylinder in compliance with current national 

regulations. Before carrying out the connection, make sure 

the cooker is compatible with the gas supply you wish to 

use. If this is not the case, follow the instructions indicated 

in the paragraph “Adapting to different types of gas.”

When using liquid gas from a cylinder, install a pressure 

regulator which complies with current national regulations.

!

 Check that the pressure of the gas supply is consistent 

with the values indicated in Table 1 (“Burner and nozzle 

specifications”). This  will  ensure  the  safe  operation  and 

longevity  of  your  appliance  while  maintaining  efficient 

energy consumption.

Connection with a rigid pipe (copper or steel)

!

 Connection to the gas system must be carried out in such a 

way as not to place any strain of any kind on the appliance.

There is an adjustable L-shaped pipe fitting on the appliance 

supply ramp and this is fitted with a seal in order to prevent 

leaks. The seal must always be replaced after rotating the 

pipe fitting (seal provided with appliance). The gas supply 

pipe fitting is a threaded 1/2 gas cylindrical male attachment.

Connecting a flexible jointless stainless steel pipe to a 

threaded attachment

The gas supply pipe fitting is a threaded 1/2 gas cylindrical 

male attachment.

These pipes must be installed so that they are never longer 

than 2000 mm when fully extended. Once connection has 

been carried out, make sure that the flexible metal pipe 

does not touch any moving parts and is not compressed.

!

 Only use pipes and seals that comply with current national 

regulations.