6

GB

Installation

!

 Please keep this instruction booklet in a safe place for future reference. If 

the appliance is sold, given away or moved, please make sure the booklet is 

also passed on to the new owners so that they may benefit from the advice 

contained within it.

!

 Please read this instruction manual carefully: it contains important information 

concerning the safe operation, installation and maintenance of the appliance.

Positioning

!

 Do not let children play with the packaging material; it should be disposed 

of in accordance with local separated waste collection standards (see 

Precautions and tips).

!

 The appliance must be installed by a qualified professional in accordance 

with the instructions provided. Incorrect installation may damage property or 

cause harm to people or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance operates properly:

•  the panels adjacent to the oven must be made of heat-resistant material.

•  cabinets with a veneer exterior must be assembled with glues which can 

withstand temperatures of up to 100°C.

•  to install the oven 

under the counter

 (see diagram) or in a 

kitchen unit

, 

the cabinet must have the following dimensions:

590 mm.

595 mm.

22,5 mm.*

20,5 mm

.

550 mm

.

570 mm.

20 mm

.

575-585 mm

.

45 mm

.

560 mm

.

550 mm.

min.

!

 The appliance must not come into contact with electrical parts once it has 

been installed. 

The indications for consumption given on the data plate have been calculated 

for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be 

removed. It is advisable to install the oven so that it rests on two strips of 

wood, or on a completely flat surface with an opening of at least 45 x 560 

mm (see diagrams).

560 mm

.

45 mm.

Centring and fixing

Secure the appliance to the cabinet:

•  Open the oven door.

•  Remove the 2 rubber plugs covering the fixing holes on the perimeter 

frame.

•  Fix the oven to the cabinet using the 2 wood screws.

•  Replace the rubber plugs.

!

 All parts which ensure the safe operation of the appliance must not be 

removable without the aid of a tool.

Electrical connection

Ovens equipped with a three-pole power supply cable are designed to operate 

with alternating current at the voltage and frequency indicated on the data 

plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by 

inserting a screwdriver into the side 

tabs of the cover. Use the screwdriver 

as a lever by pushing it down to open 

the cover (see diagram).

2. Install the power supply cable by 

loosening the cable clamp screw 

and the three wire contact screws  
L-N-

.

Connect the wires to the 

corresponding terminals: the Blue 

wire to the terminal marked (N), the 

Brown wire to the terminal marked 

(L) and the Yellow/Green wire to the 
terminal marked 

 (see diagram).

3. Secure the cable by fastening the 

clamp screw.

4. Close the cover of the terminal 

board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data 

plate (see table). 

The appliance must be directly connected to the mains using an omnipolar 

switch with a minimum contact opening of 3 mm installed between the 

appliance and the mains.  The switch must be suitable for the charge indicated 

and must comply with current electrical regulations (the earthing wire must not 

be interrupted by the switch). The supply cable must be positioned so that it 

does not come into contact with temperatures higher than 50°C at any point 

(the back panel of the oven, for example).

!

 The installer must ensure that the correct electrical connection has been 

performed and that it is fully compliant with safety regulations.

N

L