Инструкция для Ibanez Electric Basses (2013)

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

24

IT

ALIANO

MANICO

I modelli Ibanez che

montano corde in acciaio

sono dotati di truss rod

regolabili. Lo scopo di un

truss rod è di regolare il

manico per compensare la

tensione della corda. Vi

sono molte ragioni per

regolare il truss rod. Una

delle ragioni più frequenti è

il cambio delle scalature

delle corde o l’altezza dell’accordatura, che può influenzare la tensione della

corda. Le modifiche alla tensione possono influenzare l’altezza della corda,

producendo così ronzii nel tasto o note non intonate. Per regolare il truss rod,

individuare il relativo dado e regolarlo inserendo la brugola adeguata sul dado e

stringendo (in senso orario) o allentando (in senso antiorario) il perno. La tensione

del truss rod può essere misurata installando un capotasto mobile all’altezza

del primo tasto e tenendo premuta la corda all’altezza in cui il manico si congiunge

al corpo. Inserire un misuratore di spessore tra la corda e il tasto all’altezza

dell’ottavo tasto. Dovrebbe esserci una distanza da 0,3 mm a 0,5 mm. Questa

distanza è detta “neck relief” (tolleranza del manico). Una distanza eccessiva

può dare una action maggiore al centro del manico, provocando una cattiva

intonazione e un uso scomodo dello strumento. L’assenza completa di neck

relief può provocare un ronzio del tasto.

*Va prestata una cura adeguata nella regolazione del manico; consigliamo di fare eseguire questa procedura

solo a tecnici qualificati.

CORDE

Se le corde diventano sporche, scolorite o emettono un

suono sordo o un ronzio, sostituirle con delle corde

nuove. Per ottenere risultati migliori, consigliamo di

sostituire una corda alla volta, per evitare di modificare

la tensione dal manico. Se le nuove corde hanno una

scalatura diversa, può essere necessario regolare la

tensione del truss rod. (Consigliamo di fare svolgere

questa operazione solo a tecnici qualificati.) Le corde

dei bassi Ibanez sono dotate in fabbrica delle scalature

indicate di seguito. Seguire le istruzioni seguenti per il

proprio particolare modello. Le corde vanno strette

saldamente sulle meccaniche partendo da quella

superiore fino a quella inferiore, con 2 a 3 giri di corda

attorno al perno della meccanica. Nel caso di

meccaniche in cui le estremità delle corde siano inserite

nei perni, la corda può essere preventivamente tagliata alla lunghezza

appropriata, usando un tronchesino. Le meccaniche con ingranaggi ermetici

sono già lubrificate. Le viti di regolazione per la manopola di regolazione possono

essere serrate con un cacciavite a testa Phillips per aumentare la tensione.

*L’uso di corde usurate può produrre ronzio e distorsione nel suono. L’uso di corde attorcigliate può causare

ronzii o un sustain ridotto. Assicurarsi che le corde siano di forma regolare e prive di difetti prima di montarle.

Per installare la corda sul ponte,

infilare la nuova corda nei fori

appositi posti sul retro della cordiera

e farla scivolare verso l'alto, sopra

la selletta. Per ponti che richiedono

particolari istruzioni di installazione,

vedere l'appendice alla fine del manuale.

SERRA

ALLENTA

SERRA

ALLENTA

0,3 ~ 0,5 mm

8

°

 PIEDE

SERRA

ALLENTA

MODEL

4 String Basses

5 String Basses

6 String Basses

STRING GAUGE

.045, .065, .085, .105"

.045, .065, .085, .105, .130"

.032, .045, .065, .085, .105, .130"

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Оглавление инструкции
  • Страница 1 из 41
  • Страница 2 из 41
  • Страница 3 из 41
    9) If you use a strap, make sure it is completely and securely attached to the strap Our congratulations and deepest thanks on making Ibanez your choice of in- buttons before playing your bass. 10)“Don’t Try This At Home.” Doing tricks and gymnastics with your bass such as strument. Ibanez
  • Страница 4 из 41
    STRINGS NECK ENGLISH If strings become dirty, discolored, or produce a dull sound or buzz, replace the strings with new ones. For best results we recommend replacing one string at a Ibanez basses are equipped LOOSEN with adjustable truss rods. The purpose of a truss rod time, this will help to
  • Страница 5 из 41
    INTONATION Ibanez bass string action is set at the factory. However, Intonation adjustment is the operation there are many reasons that an instrument's string height can change. Instruments can be affected by changes in of adjusting the location of the string at the saddle to compensate for
  • Страница 6 из 41
    ENGLISH ACOUSTIC BRIDGE POSITION BASS CONTROLS On a full hollow bass, the entire bridge Pickup Balancer (on all two-pickup models.) The is moved forward or back to adjust intonation. Based on the 12th fret pickup balance control pot allows the user to blend between the front and rear pickups using
  • Страница 7 из 41
    !  !fÄ~åÉò= !"#$%&'()*+,-./01$234567 fÄ~åÉò= !"#$%&'()*+,-./!01234564789  !"#$%&'  !" #$ #%&'()*+,-./01234#356789:;  !"#$%&'()*+,-./01  !"#$%&'()**+,$+-' NF !"#$%  !"#$%&'($)*+,-.$%/01234-56789:;  !"#$%&'()*+,-./012-3-452678"9:/  !"#$%$&'$()*+,-./.0123!0 !"4 
  • Страница 8 из 41
                          !"  !"#$%&'()*+$,-./0,12 !"#$%&'()*+,-./0'!12 !"#$%&'()* +,-./()012 !"#$%!&'()*"++,-./0"1 !"#$%&'= !"#$%&"'() !"#$%&'()*+,-!./0123% !"#$%&'()*+,-./0(123% !"#$%&'()*+,$-./012%3 !"#$%&'()*+,-!./01$2 !"#$%&'()*+,"#'+-./01
  • Страница 9 из 41
                           !"#$%  &'()*+,-.)/01 !"#$%& '()*+,-.*/012!3 !"#$%&'()*+,-./0123456 !"#$%&'()*= !"NO !" !"#$OKMãã !"#$OKRãã ! !"#$"%&'()*+= !"#$% !"#$%&'()*+,-./0123$%4 !"#$%&'()*+, !"#$%&'()*"#$%&+,-./012/34 !5)
  • Страница 10 из 41
     !"#$%& !'()$*+,   !"#$%&'("#)*+  !"#$%&'()*+,-.  !"#$%&'() NO !"#$%&'()*+NO  !"#$%&'()* +,  !"#$%&'()*+,* !"#$%&  !"#$%&'()*+,-.  !"#$%&'()*+,-./+012314567"89M  !"#$N !"#$%&'()*"+,TTMããLPMKP? !  !"#$%&'()*+,-./012#345./6789:;  !"!#$%&'()*+,-./0123456789  
  • Страница 11 из 41
    9 
  • Страница 12 из 41
     10
  • Страница 13 из 41
    Herzlichen Glückwunsch und vielen Dank für Ihre Entscheidung für ein Instrument von Ibanez. Die Standards von Ibanez sind einzigartig. Alle Instrumente der Tonhöhe sind, ist es besser, die Saite erst wieder zu entspannen und sie dann auf die korrekte Höhe zu stimmen, als ein Überstimmen zu
  • Страница 14 из 41
    DEUTSCH SAITEN HALS Wenn die Saiten verschmutzt oder verfärbt sind, dumpf Ibanez-Instrumente für klingen oder schnarren, ersetzen Sie die Saiten durch neue. Für beste Ergebnisse empfehlen wir, eine Saite Stahlsaiten sind mit einem einstellbaren nach der anderen auszutauschen, so dass die Halsstab
  • Страница 15 из 41
    INTONATION Die Saitenlage oder “Action” von Ibanez-Basssaiten wird Die Einstellung der Intonation wird werksseitig eingestellt. Es gibt jedoch viele Anlässe, bei denen sich die Saitenlage des Instruments ändert. Die durchgeführt, indem die Position der Saite am Saitenreiter des Steges Instrumente
  • Страница 16 из 41
    POSITION DES STEGS BEIM AKUSTIKBASS Bei einem vollakustischen Bass wird der Alle Modelle mit 2 Pickups: Pickup-Balanceregler gesamte Steg vor- oder zurückgeschoben, um die Intonation zu steuern. Bewegen Der Pickup-Balanceregler blendet zwischen vorderem und hinterem Pickup hin und her mit einem Sie
  • Страница 17 из 41
    Nuestras más sinceras gracias y enhorabuena por adquirir un instrumento Ibanez. afine el instrumento. Si no está seguro de la afinación de una nota, es preferible volver a empezar, aflojar la cuerda y volver a afinar hasta el tono correcto, en lugar de arriesgarse a tensar la cuerda demasiado. Los
  • Страница 18 из 41
    CUERDAS MÁSTIL Si las cuerdas se ensucian, se decoloran o producen un sonido apagado o un zumbido, sustitúyelas por unas nuevas. Para lograr un resultado óptimo, recomendamos Los modelos Ibanez para AFLOJAR cuerdas de acero están provistos de un alma cambiar las cuerdas de una en una a fin de
  • Страница 19 из 41
    ACCIÓN OCTAVACIÓN La acción (distancia entre los trastes y la cuerda) del bajo La octavación es la operación de ajustar Ibanez se ajusta en fábrica. No obstante, la altura de las cuerdas de un instrumento puede variar por numerosas la posición de las cuerdas en la silleta del puente para compensar
  • Страница 20 из 41
    POSICIÓN DEL PUENTE PARA CAJA En un bajo de caja, el puente completo se Todos los modelos de 2 pastillas: mueve hacia delante o hacia atrás para ajustar la octavación. Basándonos en el Balance de pastillas El potenciómetro de control de balance de las armónico del 12.º traste, si la nota del
  • Страница 21 из 41
    Vous avez choisi un instrument Ibanez, nous vous remercions de ce choix et 6) Il est conseillé de remplacer régulièrement les cordes. Des cordes anciennes et sales produisent un son terne et vide et sont davantage sujettes à casser. Si les cordes sont trop tendues, vous risquez également de les
  • Страница 22 из 41
    FRANÇAIS CORDES MANCHE Si les cordes deviennent sales, changent de couleur, produisent un son terne ou des bourdonnements, remplacez-les. Pour éviter de fortes variations de tension du manche et pour obtenir de meilleurs résultats, nous vous recommandons de remplacer les cordes une à une. Lors du
  • Страница 23 из 41
    INTONATION La hauteur des cordes est réglée lors de la fabrication Le réglage de l’intonation consiste à des guitares basses Ibanez. Néanmoins, plusieurs facteurs peuvent provoquer la variation de hauteur des ajuster la position de la corde au niveau du sillet afin de compenser les cordes d’un
  • Страница 24 из 41
    FRANÇAIS POSITION DU CHEVALET ACOUSTIQUE RÉGLAGES DE LA GUITARE BASSE Sur une guitare basse creuse, l’ensemble Pour tous les modèles à deux micros : du chevalet est déplacé vers l’avant ou vers l’arrière pour régler l’intonation. En Compensateur de micro Le réglage de compensation de micro vous
  • Страница 25 из 41
    7) Non suonare il basso con corde arrugginite per evitare lesioni alle dita. Congratulazioni e grazie di cuore per avere scelto uno strumento Ibanez. Gli 8) L’estremità tagliata o spuntata di una corda di chitarra o di basso è molto aguzza; non toccarla direttamente con le dita. standard
  • Страница 26 из 41
    CORDE MANICO ITALIANO Se le corde diventano sporche, scolorite o emettono un suono sordo o un ronzio, sostituirle con delle corde nuove. Per ottenere risultati migliori, consigliamo di I modelli Ibanez che ALLENTA montano corde in acciaio sono dotati di truss rod sostituire una corda alla volta,
  • Страница 27 из 41
    INTONAZIONE L’action della corda del basso Ibanez è impostata in La regolazione dell’intonazione consiste fabbrica. Tuttavia, vi sono molte ragioni per le quali l’altezza della corda dello strumento può cambiare. Gli nel regolare la posizione della corda sulla selletta per compensare la diversa
  • Страница 28 из 41
    ITALIANO POSIZIONE DEL PONTE ACUSTICO COMANDI DEL BASSO In un basso di tipo hollow, l'intonazione Modelli con due pickup: bilanciamento dei pickup viene regolata spostando l'intero ponte in avanti o indietro. Se l'intonazione della Il controllo del bilanciamento dei pickup permette di miscelare il
  • Страница 29 из 41
    27
  • Страница 30 из 41
    0,3 ~ 0,5 mm MODEL 4 String Basses 5 String Basses 6 String Basses 28 STRING GAUGE .045, .065, .085, .105" .045, .065, .085, .105, .130" .032, .045, .065, .085, .105, .130"
  • Страница 31 из 41
    29
  • Страница 32 из 41
    30
  • Страница 33 из 41
    ATTACHMENTS  ZUBEHÖR ACCESORIOS ACCESSOIRES ACCESSORI Multi-Tool  !" Universalwerkzeug Herramienta multiusos Multi outils Strumento multiuso For PRESRIGE, PREMIUM and Grooveline • Please check the contents of the shipment first. The shipment includes Guitar, Case, Instruction Manual (this
  • Страница 34 из 41
    STRING REPLACEMENT  SAITEN ERSETZEN REMPLACEMENT DES CORDES CAMBIO DE CUERDAS SOSTITUZIONE DI UNA CORDA ATK Install the string from the back of the instrument through the string grommets or thread through the holes in the bridge. *Note; When replacing strings, check with the dealer to make sure
  • Страница 35 из 41
    B200, B205 (SRX) MR-4 (SR , BTB) The B200/B205 bridges allow two styles of string installation. • Slide the ball end into the ball end pocket. _OMML_OMR !"#$%&'( !)*+,-%O !"#$%& •  !"#$%&'()%*+,-./012  Bei den Stegen B200/B205 gibt es zwei Möglichkeiten, Saiten aufzuziehen. Les chevalets
  • Страница 36 из 41
    BASS BRIDGE  !"#$ _^ppJpqbd=E_ofadbF `ebs^ibq=ab=drfq^ob=_^ppb mrbkqb mlkqb=abi=_^ppl B120/B125/B126 (SR) B A A: Intonation adjustment screw B: Saddle height adjustment screw  !"#$%&!'  !"#$%& Intonations-Einstellschraube Reiterhöhen-Einstellschraube Écrou de réglage de l'intonation Vis
  • Страница 37 из 41
    B200 / B205 (MDB, SRX) MR-2 (BTB) B B A A Acoustic bridge (AFB) MR-4 (BTB, GVB, PIB, SDB, SR) B B C B A Standard bridge (K5, GWB, ATK) TIGHT END BASS BRIDGE (Grooveline) B B C A A A 35
  • Страница 38 из 41
    BASS CONTROLS  !"#$% KLANGREGLER AM BASS RÉGLAGES DE LA GUITARE BASSE CONTROLES DEL BAJO COMANDI DEL BASSO 2BAND EQ Passive BARTOLINI EQ 36 aguilar EQ
  • Страница 39 из 41
    3BAND EQ "VARI-MID"3BAND EQ PWC III EQ E4/E5/E6 PHAT EQ SR/BTB OTHERS 37
  • Страница 40 из 41
    The followings complies with the requirements of the EMC Directive 2004/108/EC of the European Union. No.22, 3-CHOME, SHUMOKU-CHO, HIGASHI-KU, NAGOYA, 461-8717, JAPAN AUTHORIZED REPRESENTATIVE : J.N.WAGENAARWEG 9, 1422 AK UITHOORN, NETHERLANDS 2012 Japan SEP12918
  • Страница 41 из 41