[Страница 4/11] - Мануал: вращающаяся голова Involight MINIBEAM30

Инструкция для Involight MINIBEAM30

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

2. Safety Instructions

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.

►If the device has been exposed to temperature changes due to environmental changes, do not
switch it on immediately. The arising condensation could damage the device. Leave the device
switched off until it has reached room temperature.

►Please make sure that the device be earthed.

►Please replace housing if it is broken. This fixture can be using after finished installed.

►The electric connection must carry out by qualified person.

►Make sure that the available voltage is not higher than stated at the end of this manual.

►Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.

►If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

►Please cut off the power if don't use the fixture or want to clean, maintenance.

Please be aware that damages caused by manual modifications to the device are not subject to
warranty. Keep away from non-professionals.

CAUTION!

Be careful with your operations. With a dangerous voltage you can suffer a
dangerous electric shock when touching wires!

Warning!

Damages caused by the disregard of this user manual are not subject to warranty. The
dealer will not accept liability for any resulting defects or problems.

Оглавление инструкции

Страница 1 из 12
Mini 30W White LED Beam Moving Head Light User Manual Please keep the manual carefully for future reference.
Страница 2 из 12
Thank you for your patronage. We are confident that our excellent products and service can satisfy you. For your own safety, please read this user manual carefully before installing the device. In order to install , operate, and maintain the lighting safety and correctly. We suggest that the
Страница 3 из 12
1. Description of the Device ●1*30W high power white LED; ●Power supply: 100~240VAC 50~60Hz ●Rated power: 37W ●Average of 50,000 hours of super-long LED life, low energy consumption, energy conservation and environmental protection LED; ●Quickly scan speed, Pan scanning 630 degree only 1.2 seconds,
Страница 4 из 12
2. Safety Instructions CAUTION! Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching wires! This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely
Страница 5 из 12
General Guidelines ►This device is a lighting effect for professional use on stages, in discotheques, theaters, etc., the device was designed for indoor use only. ►This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last
Страница 6 из 12
►The installation must always be secured with a secondary safety attachment, e.g. an appropriate safety rope.Never stand directly below the device when mounting, removing or servicing the fixture. ►The operator has to make sure the safety relating and machine technical installations are approved by
Страница 7 из 12
XLR Mounting socket XLR Mounting plug DMX-512 connection with DMX terminator For installations where has it has too much lines or lights environment it is recommended to use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator
Страница 8 из 12
6. Menu map and operation Display AddreSet MotorSet AutoProg MIC Cont MIC Sensy ChanTest NoSigSet Mode Set UserMode ResetDef Versions Data 1-512 PanRev TiltRev PanAdj Encoder PanMode Master/Slave Master/Slave 0-100% Set DMX channel and testing channel Close/Scene/Auto/Music Standard/Basic/User Mode
Страница 9 из 12
Channel Instruction 8 channels (Standard) Channel Value Function Display 1 2 3 4 000-255 000-255 000-255 000-255 Pan: 5 000-255 6 000-255 Pan Pan fine Tilt Tilt fine Pan/Tilt movement speed(from fast to slow;226-235 off; more than 225, the quickest speed) White Strobe 0-16 Close 16-95 Strobe from
Страница 10 из 12
Spectral wavelength analysis system Spectral wavelength analysis system Sample Item: MINIBEAM30 Testing Date: Dec.19,2013 Sample Number: Testing Time: 08:40:27 Color Technical Parameter Main Wavelength: 470.5 nm Color Temperature: 12370K 70.5 56.5 Environment Temperature: 25.0 ºC Environment
Страница 11 из 12
Cleaning and maintenance The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test. The operator has to make sure that safety-relating and machine-technical installations are inspected
Страница 12 из 12

Инструкция для Involight MINIBEAM30

Инструкции и руководства похожие на Involight MINIBEAM30

Другие инструкции и руководства из категории вращающаяся голова