![background image](/i/karcher/165568/karcher-ic-15-240-w-adv/h/karcher-ic-15-240-w-adv-019.png)
-
6
1 Stopper
Loosen the fastening screws of the
stopper.
Insert the waste container with open lid
into the device.
Tilt down the suction head.
Align the waste container in such a way
that the suction head seals off from all
direction.
Move the stoppers to touch the contain-
er and tighten the fastening screws.
1 Fastening screw of suction head
Loosen the fastening screws of the suc-
tion head on both the sides.
Press the suction head on to the waste
container and tighten the fastening
screws at the same time.
Lock the parking brakes by releasing
the drawbar.
Turn ignition key to "0" and remove it.
Danger
Risk of injury and damage! Observe the weight
of the appliance when you transport it.
Danger
In general, when shipping the machine, the
freewheel lever must be engaged in the up-
per position. Only once this has been done,
will the travel drive be ready for operation.
The machine must always be moved up or
down slopes by engaging self-propulsion.
Lock the parking brakes by releasing
the drawbar.
Turn ignition key to "0" and remove it.
Empty tank. Draw off fuel using suitable
pump.
Secure the wheels of the machine with
wheel chocks.
Secure the machine with tensioning
straps or cables.
When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.
Note:
Observe markings for fixing points on
base frame (chain symbols). When loading
or unloading the machine, it may only be
operated on gradients of max. 18%.
Danger
Risk of injury and damage! Note the weight
of the appliance in case of storage.
If the device is going to be out of service for a
longer time period, observe the following points:
Park the machine on an even surface.
Lock the parking brakes by releasing the
drawbar.
Fill fuel tank and close fuel cock.
Change engine oil.
Turn ignition key to "0" and remove it.
Unscrew spark plugs and pour approx. 3
cm³ of oil into the spark plug hole. Crank the
engine several times before replacing the
spark plug. Screw in the spark plug.
Clean the inside and outside of the ma-
chine.
Park the machine in a safe and dry place.
Disconnect battery.
Charge battery approx. every 2 months.
Open the device hood and secure it us-
ing the hood support.
1 Fuel tap
Push lever in "OFF" direction.
First switch off the appliance, remove the
key and disconnect the battery before per-
forming any cleaning or maintenance tasks
on the appliance, replacing parts or switch-
ing over to another function.
Always disconnect the battery when
working on the electrics.
– Maintenance work may only be carried
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety
regulations.
– Mobile appliances used for commercial
purposes are subject to safety inspec-
tions according to VDE 0701.
Caution
Risk of damage! Do not clean the appliance
with a water hose or high-pressure water jet
(danger of short circuits or other damage).
Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
Open the device hood and secure it us-
ing the hood support.
Clean machine with a cloth.
Blow through machine with com-
pressed air.
Close cover.
Clean the machine with a damp cloth which
has been soaked in mild detergent.
Note:
Do not use aggressive cleaning
agents.
Note:
The elapsed-time counter shows the
timing of the maintenance intervals.
Daily maintenance:
Check engine oil level.
Check axle drive oil level.
Check tyre pressure.
Check function of all operator control el-
ements.
Clean seal on suction head and large
dirt flap.
Weekly maintenance:
Check fuel pipes for leaks.
Check air filter.
Check moving parts for freedom of
movement.
Maintenance to be carried out every 100
operating hours:
Check fuel pipes for leaks.
Change engine oil (initial change after
20 operating hours).
Check spark plug.
Check battery acid level.
Check status of the brake springs and
ensure that they are fitting properly.
Check tension, wear and function of
drive belts (V-belt and circular belt).
Check the tension of the drive chains.
Note:
For description, see section on Main-
tenance work.
Note:
Where maintenance is carried out by
the customer, all service and maintenance
work must be undertaken by a qualified
specialist. If required, a specialised Archer
dealer may be contacted at any time.
Maintenance to be carried out after 20 op-
erating hours:
Carry out initial inspection.
Maintenance to be carried out every 100
operating hours
Maintenance to be carried out every 200
operating hours
Maintenance to be carried out every 300
operating hours
Turn off the appliance.
Transport
Storage
Shutdown
Close fuel cock
Maintenance and care
General notes
Cleaning
Cleaning the inside of the machine
External cleaning of the appliance
Maintenance intervals
Maintenance by the customer
Maintenance by Customer Service
19
EN