![background image](/i/karcher/166833/karcher-kmr-1700-b-lpg/h/karcher-kmr-1700-b-lpg-028.png)
28
English
– Parts (cans, etc.) with max. 70 mm
height can be swept in; place larger ob-
jects directly in the waste container.
Lock the sweep roller to "Fine tuning" mode
Î
Press the button downward and to-
wards the rear.
Lock the roller brush to "store in floating
mode" mode
Î
Press the button downward and to-
wards the front
In this mode, the contact pressure of the
roller brush can be increased as follows.
Î
Press the "forward" accelerator pedal
and the "Increase roller brush contact
pressure" pedal simultaneously.
Î
Lower the roller brush while cleaning
surfaces.
Î
Lower side brush when cleaning along
edges.
Î
Switch on dust suction while cleaning
dusty surfaces.
Î
Switch off the suction blower to protect
the dust filter against humidity.
Danger
Risk of injury! When emptying the waste
container, care should be taken to ensure
that no persons or animals are within its
swivelling range.
Danger
Danger of crushing. Never reach into the
rod assembly for the drainage mechanism.
Stay away from the area under the raised
container.
Danger
Danger of tipping. Place the machine on an
even surface during emptying.
Î
Stop the machine.
Î
Raise roller brush.
Î
The side-brushes lift up.
Î
Switch off suction blower.
Î
Raise waste container.
Î
Slowly drive towards the collection con-
tainer.
Î
Lock parking brake.
Î
Tip waste container out.
Note
A green indicator lamp indicates when the
waste container can be tilted.
Î
Tilt the waste container up to the end-
position.
Î
Release parking brake.
Î
Drive away the collection container
slowly.
Î
Lower the waste container up to the
end-position.
Î
Push in the engine speed adjustment
completely,
Î
Press brake pedal and keep it de-
pressed.
Î
Lock parking brake.
Î
Raise roller brush.
Î
The side-brushes lift up.
Î
Turn ignition key to "0" and remove it.
Note
Once the machine has been switched off,
the dust filter is shaked automatically for ap-
prox. 10 seconds.
몇
Warning
The appliance must be secured against
slippage during transport.
Î
Turn ignition key to "0" and remove it.
Î
Lock parking brake.
Î
Secure the appliance at the transport
eyelets using tension belts, ropes or
chains.
Î
Secure the wheels of the machine with
wheel chocks.
If the sweeper is going to be out of service
for a longer time period, observe the follow-
ing points:
Î
Park the sweeper on an even surface.
Î
Raise the roller brush and the side-
brushes to prevent the bristles from be-
ing damaged.
Î
Turn ignition key to "0" and remove it.
Î
Lock parking brake.
Î
Lock the sweeper to ensure that it does
not roll off.
Î
Fill fuel tank and close fuel cock.
Î
Close the gas cylinder valve.
Î
Change engine oil.
Î
Drain off the cooling water if frost is ex-
pected and check whether there is ade-
quate anti-frosting agent.
Î
Unscrew spark plugs and pour approx.
3 cm
3
of oil into the spark plug holes.
Crank the engine several times before
replacing the spark plugs. Screw in
spark plugs.
Î
Clean the inside and outside of the
sweeper.
Î
Charge the battery and clamp it off.
– Maintenance work may only be carried
out by approved customer service out-
lets or experts in this field who are famil-
iar with the respective safety
regulations.
– Mobile appliances used for commercial
purposes aer subject to safety inspec-
tions according to VDE 0701.
Î
Park the sweeper on an even surface.
Î
Turn ignition key to "0" and remove it.
Î
Lock parking brake.
몇
Warning
Risk of damage! Do not clean the appliance
with a water hose or high-pressure water jet
(danger of short circuits or other damage).
Danger
Risk of injury! Wear dust mask and protec-
tive goggles.
Î
Clean machine with a cloth.
Î
Blow through machine with compressed
air.
Î
Clean the machine with a damp cloth
which has been soaked in mild deter-
gent.
Note
Do not use aggressive cleaning agents.
Note
The elapsed-time counter shows the timing
of the maintenance intervals.
Daily maintenance:
Î
Check engine oil level.
Î
Check cooler water level.
Î
Check tyre pressure.
Î
Check the sweeping roller and the side
brush for wear and wrapped belts.
Î
Check gas pipes and connecting
screws.
Î
Check gas filter in the screw to the gas
cylinder to see if it is dirty, clean it if re-
quired (every time you change the cylin-
der).
Weekly maintenance:
Î
Clean the water cooler.
Î
Check the hydraulic oil level.
Sweeping even surfaces
Sweeping uneven surfaces
Sweeping dry floors
Sweeping damp or wet floors
Emptying waste container
Turn off the appliance.
Transport
Shutdown
Maintenance and care
General notes
Cleaning
Cleaning the inside of the machine
External cleaning of the appliance
Maintenance intervals
Maintenance by the customer