39 -  

Use the rotary switch if you want to switch over a VCR, DVD 
device or a Set Top Box.

Press the 

END

 and 

EPG

 buttons simultaneously for at least 

5 seconds. The upper left indicator on the remote control will 
blink twice.
Enter the four numbers in sequence that you found in the code 
list (e.g. 0539 for Loewe DVD player). 

After each number you enter, the indicator will blink once, after the last number 
it will blink twice. If the number was incorrect, the indicator will remain lit 
longer. The code number was not accepted. If the code was accepted with two 
blinks, you can test the functions of the device you just programmed.
If the device cannot be operated or can only be operated poorly, repeat the 
code entry with the next code from the list. If there are no other codes speci

fi

 ed 

for this manufacturer, try it using the code suggestions from the remote control. 

Setting the remote control using the suggestions from the 

remote control

Switch the device 

on

 that you want to switch over to the remote control. 

Standby mode is not enough.

Use the rotary switch if you want to switch over a VCR, DVD 
device or a Set Top Box.

Press the 

END

 and 

EPG

 buttons simultaneously for at least 

5 seconds. The upper left indicator on the remote control will 
blink twice.

Enter the the numbers 991 in sequence. The indicator will 
blink once after each number entered.

Press the 

# PIP

 button to select the 

fi

 rst code.

Point the remote control toward the device you want to switch over to the 
remote control. Observe that device. 

Now press the button   (Play) or 

On/Off

 on the remote 

control. 
Wait a moment for the device to react. If the device does not 
react, then that was not the right code. Press the 

# PIP

 button 

again to call the next code. 
Press the button   (Play) or 

On/Off

 again.

If the device reacts, press the 

EPG

 button to adopt the 

code.

Operating additional equipment

Operating other Loewe devices with the RC3 remote control

Using this remote control, you can operate additional devices from Loewe.

Use the rotary switch to select VCR, TV or a Set Top Box.
The following are preset at the factory: Loewe VCRs, Loewe TV 
sets and for STBs (Set Top Box) in Germany, the 
common d-box.

Use the driver buttons in the TV and STB position for VCR, 

DVD or Digital Recorder

You can switch over the six drive buttons 
( 

, 

, 

, 

, 

, 

 ), both for the TV and for 

the STB, to control a VCR or DVD player/recorder (the control of the integrated 
"Digital Recorder Plus" is preset at the factory):

First set the switch to the main function TV or STB.

Then press the 

END

 and 

EPG

 buttons simultaneously for at 

least 5 seconds. The upper left indicator on the remote control 
will blink twice.
Enter the the numbers 988 in sequence. The indicator will 
again blink two times.

Now set the switch to the desired function for the drive but-
tons:
to DVD, VCR or to TV, if the digital recorder is to be operated.
Press the 

# PIP

 button to complete the setting. The indicator 

will blink two times.

Setting the remote control to operate devices from other 

manufacturers

You can switch over the remote control for other VCRs, DVD players and Set Top 
Boxes if the infrared code for the device type is listed in the code list or if it is 
included in the code memory of the RC3.
Even if the manufacturer of the device is listed in the code list, it may not be 
possible to operate that device using the Loewe remote control. 

Setting the remote control using code entry

Search for the code number for your device in the code list (see as of pages 
49-53). The list is arranged according to device type – DVD, VCR, STB – and 
alphabetically according to manufacturer. Next to the manufacturer’s name, you 
will 

fi

 nd one or more code numbers. 

TV

DVD

STB

VCR

PIP

EPG

END

wxyz

wxyz

AV

jkl

def

wxyz

PIP

EPG

TV

DVD

STB

VCR

TV

DVD

STB

VCR

PIP

tuv

tuv

wxyz

TV

DVD

STB

VCR

TV

DVD

STB

VCR

EPG

END

EPG

END