Страница 2 из 16 Introduction Thank you for choosing the Studiophile Series LX4-2.1 / 5.1 studio nearfield monitor speakers. M-Audio is well known for digital audio interface technology, digital converters, audio preamps and mixers. Now, born from extensive research and development, the Studiophile LX4-2.1 System
Страница 3 из 16 Studiophile LX4 Surround System Features 1. Satellite Woofer - the Satellite Speaker’s woofer units are 4 inches in diameter with a magnetically shielded mineral-filled polypropylene cone, hightemperature voice coil and damped closed cell foam surround. It is designed to deliver balanced mid- and
Страница 4 из 16 Speaker Enclosure Front and Rear Panel Features LX4-2.1 Subwoofer, Rear 1. TRS Inputs: These jacks accept 1/4” connections with either balanced or unbalanced wiring. For balanced wiring, a three-conductor TRS plug is necessary.The input wiring of a TRS connector should be as follows: TRS TIP -
Страница 5 из 16 2. Sub Volume: Use the Sub Volume to set the Subwoofer output sound pressure level relative to other output channels as required. Once the subwoofer to satellite balance is achieved, use the Master Volume to control overall listening levels. 3. Power / Protect. LED: When the power switch is
Страница 6 из 16 LX4 Satellite Speaker, Rear The rear panel of each Satellite Speaker houses a single pair of spring-type speaker terminals. LX4 Satellite Speaker, Front The front panel of each LX4 Satellite Speaker houses single Woofer and Tweeter drivers. Installation - LX4-2.1 System For optimal performance of
Страница 7 из 16 Speaker Wire Connections Use speaker wires included in LX5-2.1 package to connect the Left and Right Speaker output terminals, found on the Subwoofer’s rear panel, to the Left and Right Speakers. TRS Balanced/Unbalanced Connections Assure that the LX4’s power switch is turned to the off position
Страница 8 из 16 Connecting to Preamp, Computer or Game Console Outputs Before connecting, make sure the output device’s power has been turned off. Plug the TRS balanced or TS unbalanced cable to the corresponding output connectors of a pre-amplifier, computer or game console. Installation - LX4-5.1 Expander For
Страница 9 из 16 Speaker Wire Connections Use speaker wires included in LX4-5.1 Expander package to connect the SL (Surround Left), SR (Surround Right) and C (Center) Speaker output terminals, found on the Subwoofer’s rear panel, to the SL, SR and C Speakers. Placing the Speakers - LX4-2.1 System Placing the
Страница 10 из 16 2. The two Left and Right speaker units and the listener should basically align to form a regular, or equilateral triangle. Refer to the following diagram. 3. Position the monitors so that the tops of the woofers are level with your ears in a normal listening environment. Refer to the following
Страница 11 из 16 Placing the Speakers - LX4-5.1 Expander Placing the speakers is one of the most important procedures in order to monitor sound accurately. To monitor with the LX4s performing to their maximum capability, an appropriate listening environment and correct placement are required. Please refer to the
Страница 12 из 16 Technical Support & Contact Information For additonal help, contact M-Audio Technical Support by telephone (626-445-8495, 9-5 PST M-F), by fax (626-445-7564) or by e-mail (techsupt@m-audio.com). If you have any questions, comments or suggestions about this or any M-Audio product, we invite you to
Страница 13 из 16 Warranty Terms M-Audio warrants products to be free from defects in materials and workmanship, under normal use and provided that the product is owned by the original, registered user. Visit www.m-audio.com/warranty for terms and limitations applying to your specific product. Warranty Registration
Страница 14 из 16 Appendix A - Technical Specifications Type: 3-way studio reference with subwoofer (2.1 System), expandable to 5.1 Subwoofer Driver: 8 inch diameter, specially-developed curved-profile pulp cone, high-temperature voice coil and damped closed cell foam surround designed for sub-frequency pressure