13

DE

Rotary hammer

INTENDED USE

●

  This tool is intended for hammer drilling in concrete, 

brick and stone; for drilling in wood, metal and plas-
tic as well as for screwdriving (speci

fi

 c  accessories 

should be used)

●

  The hammering system in this tool outperforms any 

traditional ratcheting drill when drilling in concrete

●

  This tool is designed for use in combination with all 

standard SDS+ accessories

TECHNICAL SPECIFICATIONS   

 1 

PRODUCT ELEMENTS   

 2 

1 On/Off 

switch

2  Wheel for maximum speed control
3  Switch locking button
4  Switch for changing direction of rotation
5  Switch for selecting operating mode
6 Locking 

sleeve

7 Auxiliary 

handle

SAFETY

WARNING!  Read all instructions. Failure to follow all 
instructions listed below may result in electric shock, 

fi

 re 

and/or serious injury. 

●

  Wear ear protectors with hammer drills (exposure to 

noise can cause hearing loss)

●

  Use auxiliary handles supplied with the tool (loss of 

control can cause personal injury)

●

  Avoid damage that can be caused by screws, nails 

and other elements in your workpiece; remove them 
before you start working

●

  Always keep the cord away from moving parts of the 

tool

●

  When you put away the tool, switch off the motor and 

ensure that all moving parts have come to a complete 
standstill

●

  Use completely unrolled and safe extension cords 

with a capacity of 16 Amps (UK 13 Amps)

●

  In case of electrical or mechanical malfunction, im-

mediately switch off the tool and disconnect the plug

●

  SBM Group can assure 

fl

 awless functioning of the 

tool only when original accessories are used

●

  Use only accessories with an allowable speed match-

ing at least the highest no-load speed of the tool

●

  This tool should not be used by people under the age 

of 16 years

●

  Be careful not to drill or drive into areas where electri-

cal wires may be contacted

●

  If the cord is damaged or cut through while working, 

do not touch the cord, but immediately disconnect the 
plug

●

  Never use tool when cord is damaged; have it re-

placed by a quali

fi

 ed person

●

  Always check that the supply voltage is the same as 

the voltage indicated on the nameplate of the tool 
(tools with a rating of 230V or 240V can also be con-
nected to a 220V supply)

●

  If the drill bit becomes unexpectedly jammed (caus-

ing a sudden, dangerous reaction), immediately 
switch off the tool

●

  Be aware of the forces that occur as a result of jam-

ming (especially when drilling metals); always hold 
the tool 

fi

 rmly with both hands and take a secure 

stance

●

  Always disconnect plug from power source before 

making any adjustment or changing any accessory

●

  Holding the tool 

-  keep the ventilation slots uncovered
-  do not apply too much pressure on the tool; let the 

tool do the work for you

Your machine is double insulated in accord-
ance with  EN 50144; therefore no earthwire is 
required

MAINTENANCE

Make sure that the machine is not live when 
carrying out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, 
preferably after each use. Keep the ventilation slots free 
from dust and dirt.If the dirt does not come off use a soft 
cloth moistened with soapy water. Never use solvents 
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
Every six months it is recommended to take your ma-
chine to Service Center to change the grease.
Should a fault occur, e.g. after wear of a part, please 
contact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during 
transport, it is delivered in a sturdy packaging. Most of 
the packaging materials can be recycled. Take these 
materials to the appropriate recycling locations. Take 
your unwanted machines to your local SBM Group deal-
er. Here they will be disposed of in an environmentally 
safe way.

English