6

Rotary hammer

INTENDED USE

●

 This tool is intended for hammer drilling in concrete, brick 

and stone; for drilling in wood, metal and plastic as well as for 
screwdriving (speci

fi

 c accessories should be used)

●

 The hammering system in this tool outperforms any tradi-

tional ratcheting drill when drilling in concrete

●

 This tool is designed for use in combination with all stand-

ard SDS+ accessories

TECHNICAL SPECIFICATIONS 

 1 

PRODUCT ELEMENTS 

 2 

1 

On/Off switch

2

 Switch locking button

3 

Switch for changing direction of rotation

4 

Switch for selecting operating mode

5 

Locking sleeve

6 

Auxiliary handle

SAFETY

WARNING!  Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, 

fi

 re 

and/or serious injury. 

●

 Wear ear protectors with hammer drills (exposure to 

noise can cause hearing loss)

●

 Use auxiliary handles supplied with the tool (loss of con-

trol can cause personal injury)

●

 Avoid damage that can be caused by screws, nails and 

other elements in your workpiece; remove them before 
you start working

●

 Always keep the cord away from moving parts of the 

tool

●

 When you put away the tool, switch off the motor and 

ensure that all moving parts have come to a complete 
standstill

●

 Use completely unrolled and safe extension cords with 

a capacity of 16 Amps (UK 13 Amps)

●

 In case of electrical or mechanical malfunction, immedi-

ately switch off the tool and disconnect the plug

●

 SBM Group can assure 

fl

 awless functioning of the tool 

only when original accessories are used

●

 Use only accessories with an allowable speed matching 

at least the highest no-load speed of the tool

●

 This tool should not be used by people under the age 

of 16 years

●

 Be careful not to drill or drive into areas where electrical 

wires may be contacted

●

 If the cord is damaged or cut through while working, do 

not touch the cord, but immediately disconnect the plug

●

 Never use tool when cord is damaged; have it replaced 

by a quali

fi

 ed person

●

 Always check that the supply voltage is the same as 

the voltage indicated on the nameplate of the tool (tools 
with a rating of 230V or 240V can also be connected to a 
220V supply)

●

 If the drill bit becomes unexpectedly jammed (causing 

a sudden, dangerous reaction), immediately switch off the 
tool

●

 Be aware of the forces that occur as a result of jamming 

(especially when drilling metals); always hold the tool 

fi

 rmly with both hands and take a secure stance

●

 Always disconnect plug from power source before mak-

ing any adjustment or changing any accessory

●

 Holding the tool 

- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the tool 
do the work for you

Your machine is double insulated in accord-
ance with  EN 50144; therefore no earthwire 
is required

MAINTENANCE

Make sure that the machine is not live when 
carrying out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, 
preferably after each use. Keep the ventilation slots free 
from dust and dirt.If the dirt does not come off use a soft 
cloth moistened with soapy water. Never use solvents 
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
Every six months it is recommended to take your machine 
to Service Center to change the grease.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during 
transport, it is delivered in a sturdy packaging. Most of the 
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here 
they will be disposed of in an environmentally safe way.

English