[Страница 12/20] - Руководство: аудиосистема Line 6 StageSource L2t, StageSource L2m

Инструкция для Line 6 StageSource L2t, StageSource L2m

(скачивание инструкции бесплатно)

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

Bout

L6 Link

L6 LINK is a proprietary digital networking protocol developed by Line 6 to enable easy, reliable, one-cable connectivity between various Line 6 products.

Up to nine StageSource speakers (L2t, L2m, L3t, and L3m) and nine L3s subwoofers can be connected via L6 LINK, and channel assignment is automatic,

with the first speaker in the chain (master) providing the digital audio channels distributed to all other speakers in the network. All L3s and vertically-

oriented StageSource speakers (L3t/m and L2t/m) follow channel assignment shown in the table below. For example, connecting two upright L2t or L2m

speakers together automatically configures them as left and right. Connecting three upright L2t/L2m speakers together configures them as left, mono

center (left + right), and right. Placing any L2t/L2m in the L6 LINK network on its side assumes it will be used as a floor monitor, configures it as left +

right, and the remaining speakers follow the behavior in the table below. Each speaker’s rear panel L6 LINK display will indicate the current assignment:

Left (“L”), right (“r”), or L + R (“b” for both).

When connecting one or more L3s subs with StageSource speakers, crossover points are selected automatically.

When used in conjunction with a StageScape M20d mixer, channel assignments behave as above, except any StageSource L3t/m and L2t/m speakers laid

on their side are, by default, fed by monitor feed A, B, C, and D, respectively. Furthermore, any speaker on the network can have its channel assignment

changed manually from the StageScape M20d touch screen interface. In this case, each speaker’s rear panel L6 LINK display will indicate its sequential

number in the network. All speakers are numbered independently.

We strongly recommend the use of 110-ohm AES/EBU digital cables for use with Line 6 LINK connections for StageScape and StageSource. The use of

standard XLR cables may yield inconsistent results because of the varying quality of commercially-available XLR cables. Cables longer than 50 feet are

not recommended for L6 LINK.

Number of L3s or Vertical

L2t/L2m speakers

Default Audio Channel Assignment

Spkr 1

Spkr 2

Spkr 3

Spkr 4

Spkr 5

Spkr 6

Spkr 7

Spkr 8

Spkr 9

L + R

Оглавление инструкции

Страница 1 из 21
® StageSource L2t / L2m Pilot’s Guide Guide de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto 取扱説明書 40-00-0338 Pilot’s Handbook available @ www.line6.com/manuals Rev F
Страница 2 из 21
Important Safety Instructions C AU T IO N R ISK O F E LE C TR IC SH O C K DO NOT O PE N WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
Страница 3 из 21
You should read these Important Safety Instructions. Keep these instructions in a safe place • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any
Страница 4 из 21
Welcome! StageSource L2t / L2m Speaker For the solo performer or duo, the StageSource L2t is a simple, powerful, and compact integrated live sound solution. Used as a standalone PA system, performers can benefit from a feature set designed to cover all their needs, including a built-in mixer with
Страница 5 из 21
StageSource L2t / L2m Height 23-3/4” / 603 mm Width 12-1/4” / 312 mm Depth 12-1/4” / 312 mm Weight 39.1 lbs / 17.7 kg
Страница 6 из 21
L2t / L2m Callouts 1. LED – The front-panel LED glows white when the speaker is powered, flashes red when the limiter circuit is active, and glows blue when receiving communication from StageScape M20d. 2. Logo – The Line 6 logo badge can be rotated 90°. Gently pull outward, rotate to match the
Страница 7 из 21
StageSource L2t
Страница 8 из 21
L2t Side Panel 1. Input Jack – Connect microphones or line-level equipment to the combi (XLR or 1/4-inch) inputs. The 1/4-inch input can accept unbalanced (Tip-Sleeve) or balanced (Tip-Ring-Sleeve) cables. When connecting an acoustic guitar, use Channel 1. 2. Pad Switch – If the input source is
Страница 9 из 21
StageSource L2t / L2m
Страница 10 из 21
L2t / L2m Back Panel 10. Line Input – Connect the line-level output of your mixer to the combi (XLR or 1/4-inch) Line input. The 1/4-inch input can accept unbalanced (Tip-Sleeve) or balanced (Tip-Ring-Sleeve) cables. The Signal LED lights green when a signal is present and may flash red if the
Страница 11 из 21
L3s sub with one L2t speaker (on stage) L3s sub with one L2t speaker (on floor or low stage) Use one short speaker pole (not included) Use one long speaker pole (not included); never use any pole longer than 24-3/4” (626 mm) in this configuration L3s sub with two L2t speakers Use two short speaker
Страница 12 из 21
About L6 LINKTM L6 LINK is a proprietary digital networking protocol developed by Line 6 to enable easy, reliable, one-cable connectivity between various Line 6 products. Up to nine StageSource speakers (L2t, L2m, L3t, and L3m) and nine L3s subwoofers can be connected via L6 LINK, and channel
Страница 13 из 21
Suspending the L2t / L2m The L2t and L2m provide four threaded M10 attachment points for suspension and one threaded M10 attachment point for pull-back and aiming the speaker. These are designed to allow for suspending the loudspeaker only by a qualified professional familiar with safe rigging
Страница 14 из 21
Traditional Applications AUX INPUT L/R INPUT CHANNEL 1 Solo Artist INPUT CHANNEL 2 L2t can provide portable amplification for singer-songwriters, complete with EQ, reverb and modulation for each channel. Connect your acoustic guitar to the side panel Channel 1, which features Acoustic Modeling.
Страница 15 из 21
Applications with L6 LINKTM AUX INPUT L/R INPUT CHANNEL 1 Small Club Duet L6 LINK provides an easy way for two artists—each with an L2t—to blend their signals together without the need for an external mixer. Connect the guitars to each speaker’s Channel 1, which features Acoustic Modeling. Connect
Страница 16 из 21
Small PA with Subs When using a traditional mixer with one or more L2t/L2m speakers and one or more L3s subs connected via L6 LINK, connect both the Main Left and Main Right outputs of the mixer to one L3s’s Left and Right inputs. L6 LINK IN L6 LINK IN L6 LINK OUT/THRU L6 LINK OUT/THRU Connect the
Страница 17 из 21
Large PA with Subs and L2m Monitors When using a traditional mixer with one or more L3/L2 speakers and one or more L3s subs connected via L6 LINK, connect both the Main Left and Main Right outputs of the mixer to one L2 or L3s’s Left and Right inputs. Continue daisy-chaining speakers via L6 LINK.
Страница 18 из 21
StageScape M20d—Small PA Connect the L6 LINK out from a StageScape M20d mixer to the rear panel L6 LINK In on any speaker in the network. Any L2t/L2m speakers and L3s subs on an L6 LINK network are numbered independently. In this illustration, the two L3s subs (labeled SUB 1 and 2) will, by
Страница 19 из 21
StageScape M20d—Large PA In the illustration below, four L3s subs (labeled SUB 1-4), four L3t/L3m speakers, and three L2t/L2m speakers (independently numbered 1-7) are daisychained from an M20d mixer. The subs and upright speakers automatically configure themselves to be a powerful stereo mains
Страница 20 из 21
Страница 21 из 21

Инструкция для Line 6 StageSource L2t, StageSource L2m

Инструкции и руководства похожие на Line 6 StageSource L2t, StageSource L2m

Другие инструкции и руководства из категории аудиосистема