Инструкция для Loewe Digital TV retrofit kit 2 T-CI

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

9

Initial start-up

Digital radio stations
search and store

Your receiver can receive and play radio
programs in high quality as well as TV
programs.

Note:

 Digital radio programs are not

broadcasted in the DVB-T standard in all
regions at present.

Radio stations are stored in a separate station
table.

You can search for and store digital radio
stations in ”Radio-menu”.
1. Select radio mode.
2. Call the Radio menu with the 

M

 button and

select the ”Radio stations” line.

3. Confirm with 

OK

.

4. You can have the radio stations searched for

automatically or manually.

Radio menu

Sound

Time and date

OK

M

i

E

Back

Info

End

Timer functions

Radio stations

M

Radio mode:  1 

BBC

Station 
Station table
Volume

OK

i

Info
Menu
TV mode
EPG

Screen shutdown in 06 seconds

OK

OK

E

Screen shutdown off
Previous station
Scan stations
Language/sound selection

In the ”Manual adjustment” menu you can
decide whether to search for an store ”all”
digital radio stations or ”Only new radio
stations”.

You can search for channels or frequencies.
Follow the wizard.

5. Finally enter from which program place the

found stations are to be stored.

6. Press the 

OK

 button.

You now get a summary of the settings you
have made.

7. Select the line ”Start search”.
8. Start the search with 

OK

.

If radio stations have been found and stored
you get a station table at the end.

Manual
station setting

You can also search for and store stations
manually. However, detailed knowledge is
necessary for manual programming.

1. Activate the appropriate menu – depending

on whether you want to set TV or radio
stations – in the respective mode (TV or
Radio) with the 

M

 button.

2. Select ”Settings – Stations” in the TV-menu

or ”Radio Stations” in the Radio menu.

3. Select the item

”Manual adjustment”.

4. Then enter the necessary setting parameters

for every menu item. You can get
explanations of the individual menu items
when the 

i

 button is shown in the menu

and you press this button on the remote
control.

Note

Several radio and TV stations can be broadcast
on every channel.

31789_001 DVB_T_V3_GB

13.11.2003, 15:27 Uhr

9

1
2
3
4
5
6
7
8
9
10
11
12
13
14
Оглавление инструкции
  • Страница 1 из 15
    Operating instructions. Digital TV retrofit kit 2 T-CI Accessories. 233-31789.001 ■ 1 31789_001 DVB_T_V3_GB 1 13.11.2003, 15:27 Uhr
  • Страница 2 из 15
    Contents Welcome 3 General information 3 Connecting antenna 4 Determining antenna position/aligning the antenna 4 Connections on rear of unit Manufactured under license from Dolby Laboratories. „Dolby“ and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works. ©
  • Страница 3 из 15
    Welcome Thank you General information for and congratulations on choosing the Loewe Digital-TV upgrade kit 2 T-CI. Range of stations This integrated digital receiver module with two slots for Common-Interface modules (CI) enable you to receive a number of free digital and coded TV stations which
  • Страница 4 из 15
    Connecting antenna Connect the antenna cable from the roof antenna to the antenna socket ”VHF/UHF IN” on the back of your TV set to receive digitally broadcast programs. Determining antenna position and aligning the antenna An indoor antenna can also be used under good reception conditions. Passive
  • Страница 5 из 15
    Connections on rear of unit Signal Box Spheros 42 HD C R Y SAT Antenna socket terrestrial (DVB-T) CR/ PR UHF/VHF CB/ PB COMPONENT IN AV 1 PIP UHF/VHF L AUDIO IN 3 R R L L AUDIO IN 1 AV 3 AV 2 (RGB) (RGB/YUV) S U R SUB DIGITAL RC5/ IR- AUDIO IN 2 SYSTEM VGA TV set DIG IN 1 RC5/RC6 SERVICE IR COMMON
  • Страница 6 из 15
    Connections on rear of unit Articos 55 Slots for Common Interface modules Digital sound output 1 C R S U R DIG OUT COMMON INTERFACE DIGITAL-TV SUB CRTL L DVI IN VHF/UHF COMPONENT IN COM DIGITAL-TV OUT AUDIO IN 3 R L Y PIP VHF/UHF AV 1 AV 2 (RGB) Connect antenna/ cable system (analog) This
  • Страница 7 из 15
    Initial start-up Preparing for initial installation Pressing the M button returns you to ”Settings”. • Make sure an antenna for the VHF/UHF range is connected to the ”IN VHF/UHF” antenna socket. With this antenna you can receive both digital and analog stations providing they are broadcasted in
  • Страница 8 из 15
    Initial start-up Inserting the CommonInterface module 1. Switch off your TV set with the On-Off switch on the TV. 2. First push the Smartcard into the CI module as far as possible. The side with the golden contact chip neeeds to face the side of the module printed with the provider’s logo. Printed
  • Страница 9 из 15
    Initial start-up Digital radio stations search and store Your receiver can receive and play radio programs in high quality as well as TV programs. Note: Digital radio programs are not broadcasted in the DVB-T standard in all regions at present. Radio stations are stored in a separate station table.
  • Страница 10 из 15
    Daily handling Changing stations with the station table The station table shows the currently stored stations in numerical order: Channel overview: TV AVS AV3 AV2 AV1 0 1 EURONEWS 2 EURONEWS D D 3 TVC INT. D 4 ANDALUC D 5 CANAL CA D 6 ETB SAT Numerical 7 RADIO 8 RADIOS E 9 TM SAT/L 10 CNN INT. 11
  • Страница 11 из 15
    Daily handling Notes: Picture in picture (PIP) • Selection menus are only available as long as the status bar is displayed. However, you can call it again at any time by pressing the E button on your remote control. You can watch two analog or one digital and one analog program on your screen at
  • Страница 12 из 15
    What to do when... Malfunctions, their causes and remedies Problem Possible cause and remedy No reception with active antenna Activate the supply voltage, see page 4 chapter ”Connecting antennae”. Picture and sound interference (block formation) Optimize the position or alignment of the reception
  • Страница 13 из 15
    Problem Possible cause and remedy No coded programs are shown in the station table although the CI module and the Smartcard of the provider are used. CI module and/or Smartcard are possibly not inserted correctly (see the section ”Connection and initial start-up”). You can check whether the module
  • Страница 14 из 15
    Index CI module (Common Interface) EPG A CI module is a decoder module for digital TV and radio programs according to the CI standard. Electronic Program Guide: your TV“s electronic program guide To show the coded programs a released Smartcard of the program provider is required in addition to a CI
  • Страница 15 из 15