14
15
...........................10 mm
...........................16 mm
.............................6 mm
......................0-500 min
-1
...........................10 Nm
...........................19 Nm
...........................15 Nm
.............................120
..............................45
...........................12 V
.........................960 g
........................58,5 dB (A)
.......................< 2,5 m/s
2
..........................1,5 m/s
2
ENGLISH
ENGLISH
BATTERIES
New battery packs reach full loading capacity after 4 - 5
chargings and dischargings. Battery packs which have not
been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will vibrate
for about 5 seconds, the fuel gauge will flash,and then the
tool will turn OFF. To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the
battery could become to high. If this happens, the fuel
gauge will flash and the battery pack cool and then continue
work.
MAINTENANCE
If the supply cord of this appliance is damaged, it must only
be replaced by a repair shop appointed by the manufacturer,
because special purpose tools are required
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Milwaukee Electric Tool,
Max-Eyth-Straße 10, D-71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before
starting the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Remove the battery pack before starting any
work on the machine.
TECHNICAL DATA
Drilling capacity in steel ...........................................................
Drilling capacity in wood ..........................................................
Wood screws (without pre-drilling) ..........................................
No-load speed .........................................................................
Torque *1
Low torque max. ...................................................................
High torque max. ..................................................................
Static jamming moment .......................................................
Screwing capacity with one fully charged battery (1,5 Ah) : *2
5x60 Soft wood .....................................................................
6x80 Soft wood .....................................................................
Battery voltage ........................................................................
Weight with battery ..................................................................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) .......................................
The noise level when working can exceed 80 dB (A).
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value a
h
..................................................
Uncertainty K ........................................................................
*1Measured according to Milwaukee norm N 877318
*2 The values stated are reference values.
Actual values might differ, depending on the material and
quality of the screws.
WARNING! Read all safety warnings and all
instructions, including those given in the accompanying
brochure.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Wear ear protectors.
Exposure to noise can cause hearing
loss.
Sawdust and splinters must not be removed while the
machine is running.
When working in walls ceiling, or floor, take care to avoid
electric cables and gas or waterpipes.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. Milwaukee Distributors offer to
retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System C12 chargers for charging System C12
battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
SPECIFIED CONDITIONS OF USE
The battery screwdriver is designed for drilling and
screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. EN 60745, EN 55014-1, EN 55014-2, in
accordance with the regulations 98/37/EC, 2004/108/EC
Rainer Kumpf
Manager Product Development
Winnenden, 2007-10-09
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
...........................10 mm
...........................16 mm
.............................6 mm
......................0-500 min
-1
...........................10 Nm
...........................19 Nm
...........................15 Nm
.............................120
..............................45
...........................12 V
.........................960 g
........................58.5 dB (A)
.......................< 2.5 m/s
2
..........................1.5 m/s
2
