“Roger” in order to prevent his correspondent that it was his turn to talk. The
word “Roger” has been replaced by a significant beep. There comes
“Roger
beep”
from.
Note:
the
Roger beep
also sounds in the loudspeaker if the
Beep
function is
active. If the
Beep
function is not active, only the correspondent can hear
the
Roger Beep
.
M2
See § 14
MEM
.
11) MIC GAIN
Adjustment of the sensitivity level of the microphone.
The normal position of this function is set to maximum clockwise.
12) HI-CUT ~ DW ~ M6
HI-CUT
(short press)
Eliminates high frequency interferences. Has to be used in accordance with
the reception conditions. A short press activates the
HI-Cut
filter and
«HIC»
appears on the display. A new press disables the function and
«HIC»
disap-
pears.
DW
(long press)
A longer press (1 second) allows activating the
DW
(Dual Watch).This func-
tion lets you watch over channel 19 or 9 and the channel you are using. The
first long press activates the
DW
function between channel
19
and the busy
channel. A new press activates the function between channel
9
and the
busy channel.
«DW»
is displayed. The number of the selected channel, the
memorized channel included, and channel 19 or 9 are alternately displayed.
«EMG»
is also displayed at the same time as channel 19 or 9. The selected
channel can be modified during the dual watch. A new long press on
DW
disables the
DW
function.
M6
See § 14
MEM
.
13) VOX ~ VOX SET
VOX
(short press)
Can be used in mode
CB
or
PA
. The
VOX
function allows transmitting by
speaking into the original microphone (or in the optional vox microphone)
without pressing the
PTT
switch. The use of an optional vox mike connected
to the rear panel of the transceiver (
C
) disables the original microphone.
Press shortly the
VOX
key in order to activate the
VOX
function.
«VOX»
appears on the display. A new press on the
VOX
key disables the function
«VOX»
disappears.
VOX SET
(long press)
Press during 1 second the
VOX
key in order to activate the function.
Vox adjustment
.
Three adjustments are possible: Sensitivity / Anti-vox level
/ Vox delay time . Press shortly the
VOX
key in order to go to the following
adjustment (looping , , ).
The display shows the type of adjustment followed by its level.
-
Sensitivity
: allows the adjustment of the microphone (original one or
optional vox) for an optimum transmission quality. Adjustable level from 1
(high level) to 9 (low level) by rotating the channel knob or with the
UP/DN
keys of the original microphone. corresponds to the
S
ensitivity
L
evel.
-
Anti-Vox
: allows disabling the transmission generated by the surrounding
noise. The level is adjustable from 0 (Off) to 9 (low level) by rotating the chan-
nel knob or with the
UP/DN
keys of the original microphone. corresponds
to
A
nti-vox
L
evel.
-
Delay time
: allows avoiding the sudden cut of the transmission by adding
a delay at the end of speaking. The level is adjustable from 1 (short delay)
to 9 (long delay) by rotating the channel selector or with the
UP/DN
keys of
the original microphone. corresponds to
D
elay
T
ime.
Once the adjustments are done, press during 1 second the
VOX
key in order
to quit the
Vox Adjustment
mode.
14) MEM ~ F
MEM
(short press)
6 channels can be memorized (
M1
to
M6
) with following parameters: AM
(except for
EC
and
U
configurations) or FM; NB/ANL; HI-CUT (and CEPT/ENG
in
U
configuration).
To memorize:
- press
MEM
shortly;
«MEM»
is blinking.
English
33