7

GB

Cordless drill/driver

INTENDED USE

This tool is intended for drilling in wood, metal, ceramic and 
plastic; tools with electronic speed control and left/right rotation 
are also suitable for screwdriving and thread cutting

TECHNICAL SPECIFICATIONS  

 1 

PRODUCT ELEMENTS  

 2 

1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control

SAFETY

WARNING!  Read all instructions. Failure to follow all instructions 
listed below may result in electric shock, 

fi

 re and/or serious 

injury. 

•  Ensure the switch is in the off position before inserting battery 

pack. Inserting the battery pack into power tools that have the 
switch on invites accidents.

•  Recharge only with the charger speci

fi

 ed by the manufacturer. 

A charger that is suitable for one type of battery pack may 
create a risk of 

fi

 re when used with another battery pack.

•  Use power tools only with speci

fi

 cally designated battery 

packs. Use of any other battery packs may create a risk of 
injury and 

fi

 re.

•  Avoid damage that can be caused by screws, nails and other 

elements in your workpiece; remove them before you start 
working

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the charger (chargers 
with a rating of 230V or 240V can also be connected to a 
220V supply)

•  In case of electrical or mechanical malfunction, immediately 

switch off the tool or unplug charger from power source

•  SBM Group can assure 

fl

 awless functioning of the tool only 

when original accessories are used

•  Use only accessories with an allowable speed matching at 

least the highest no-load speed of the tool

•  This tool should not be used by people under the age of 16 

years

•  Be careful not to drill or drive into areas where electrical wires 

may be contacted

•  Ensure that switch (2) is in the middle (locking) position 

before making any adjustments or changing accessories as 
well as when carrying or storing the tool

•  Do not touch the contacts in the charger
•  Do not expose tool/charger/battery to rain
•  Never charge battery outdoors
•  Store tool/charger/battery in locations where temperature will 

not exceed 40° C or drop below 0° C

•  Batteries will explode in 

fi

 re, so do not burn battery for any 

reason

•  When damaged, and under extreme usage and temperature 

conditions, batteries may start to leak

-  if liquid comes into contact with the skin, wash quickly with 

soap and water, then with lemon juice or vinegar

-  if liquid gets into the eyes, 

fl

 ush eyes with clean water for 

a minimum of 10 minutes and seek immediately medical 
attention

•  When battery is not in tool or charger, it should be kept away 

from metal objects such as nails, screws, keys etc. to prevent 
short-circuit

•  Do not use charger when damaged; take it to one of the 

of

fi

 cially registered SBM Group Service Stations for a safety 

check

•  Do not use battery when damaged; it should be replaced 

immediately

•  Do not disassemble charger or battery
•  Do not attempt to recharge non-rechargeable batteries with 

the charger

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•  Do not connect the blue (= neutral) or brown (= live) wire in 

the cord of the charger to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of the charger, 

it must be disposed of safely and not left unattended

To ensure longer service life and proper performance 
of the battery, take the following actions when you 
start using new battery: 

1. Use the new battery, without recharging it, till its complete 
discharge. 
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to reach 
the nominal battery capacity.

MAINTENANCE

Make sure that the machine is not live when carrying 
out maintenance work on the motor. 

Regularly clean the machine housing with a soft cloth, preferably 
after each use. Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy 
water. Never use solvents such as petrol, alcohol, ammonia 
water, etc. These solvents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please contact 
your local SBM Group dealer.

ENVIRONMENT

In order to prevent the machine from damage during transport, 
it is delivered in a sturdy packaging. Most of the packaging 
materials can be recycled. Take these materials to the 
appropriate recycling locations. Take your unwanted machines 
to your local SBM Group dealer. Here they will be disposed of in 
an environmentally safe way.
NiCd batteries can be recycled. Deliver them to a disposal site 
for chemical waste so that they can be recycled or disposed of 
in an environmentally friendly manner.