Инструкция для GIGABYTE GA-790XT-USB3 (REV.1)

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

BIOS Setup

- 40 -

  CPU Host Clock Control, CPU Frequency (MHz), Set Memory Clock, Memory Clock

 

The settings under the four items above are synchronous to those under the same items on the MB In-
telligent Tweaker(M.I.T.)
 main menu.

  DCTs Mode

 

Allows you to set memory control mode.

 

Ganged   

Sets memory control mode to single dual-channel.

 

Unganged   

Sets memory control mode to two single-channel. (Default)

  DDR3 Timing Items

 

Manual allows all DDR3 Timing items below to be configurable.

 

Options are: Auto (default), Manual.

  DRAM Configuration

CMOS Setup Utility-Copyright (C) 1984-2009 Award Software

DRAM Configuration

  CPU Host Clock Control 

[Auto]

x  CPU Frequency(MHz)   

 200

  Set Memory Clock 

 

[Auto]

x  Memory Clock   

 

 x6.66 

1333Mhz

  DCTs Mode 

 

 

[Unganged]

  DDR3 Timing Items   

[Auto] 

SPD 

Auto

x  CAS# latency   

 

Auto 

  9T 

  9T

x  RAS to CAS R/W Delay 

Auto 

  9T 

  9T

x  Row Precharge Time   

Auto 

  9T 

  9T

x  Minimum RAS Active Time 

Auto 

24T 

24T

x  1T/2T Command Timing 

Auto 

   -- 

   --

x  TwTr Command Delay   

Auto 

  5T 

  5T

x  Trfc0 for DIMM1 

 

Auto 

110ns 

110ns

x  Trfc2 for DIMM2 

 

Auto 

-- 

--

x  Trfc1 for DIMM3 

 

Auto 

-- 

--

x  Trfc3 for DIMM4 

 

Auto 

-- 

--

x  Write Recovery Time   

Auto 

10T 

10T

x  Precharge Time   

 

Auto 

  5T 

  5T

x  Row Cycle Time  

 

Auto 

33T 

33T

higf

: Move 

Enter: Select 

+/-/PU/PD: Value 

F10: Save 

ESC: Exit 

F1: General Help

 

F5: Previous Values 

F6: Fail-Safe Defaults   

F7: Optimized Defaults

Item Help

Menu Level 

CMOS Setup Utility-Copyright (C) 1984-2009 Award Software

DRAM Configuration

higf

: Move 

Enter: Select 

+/-/PU/PD: Value 

F10: Save 

ESC: Exit 

F1: General Help

 

F5: Previous Values 

F6: Fail-Safe Defaults   

F7: Optimized Defaults

Item Help

Menu Level 

x  RAS to RAS Delay 

 

Auto 

  4T 

  4T

  **DCTs Drive Strength** 

        DCT0                   DCT1

  ProcOdt(ohms)   

[Auto]

 

   60 

[Auto] 

 

240

  DQS drive Strength 

[Auto]

 

1.0x 

[Auto] 

1.5x

  Data drive Strength 

[Auto]

 

1.0x 

[Auto] 

1.5x

  MEMCLK drive Strength 

[Auto]

 

1.25x 

[Auto] 

1.5x

  Addr/Cmd drive Strength 

[Auto]

 

1.5x 

[Auto] 

2.0x

  CS/ODT drive Strength 

[Auto]

 

1.5x 

[Auto] 

2.0x

  CKE drive Strength 

[Auto]

 

1.5x 

[Auto] 

2.0x

  Bank Interleaving 

 

[Enabled]

  Channel interleave 

 

[Enabled]

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
Оглавление инструкции

Document Outline