“Time” button
•
Enables quicker washing by shortening the
programme duration.
•
Recommendable for small loads or only lightly soiled
laundry.
“Cold wash” button
•
Saves energy used for water heating while
maintaining good wash result.
•
Recommendable for lightly soiled laundry without stains.
•
Make sure that your detergent is suitable for cold
wash temperatures (15 or 20 °C).
•
Mainly selectable on the lowest temperature step of
the programmes
“Extra water” button
•
More water is added and rinse cycle is prolonged.
•
This option is particularly suitable for areas with very
soft water, washing baby linen and helping people
with allergies.
“Rinse Hold” button
•
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•
This option is particularly recommended for the
“Synthetic”, “Mix” and “Sensitive” programmes.
•
It is useful if you want to postpone spinning to a later
time, or if you want to drain out only.
•
If you select “Rinse Hold”, do not leave items to soak
for too long.
•
As soon as the appliance stops in the rinse hold, the
“Rinse hold” lamp of the sequence indicator lights up and
the lamp next to the
“Start/Pause”
button flashes.
Terminate the “Rinse Hold” option:
•
Press the
“Start/Pause”
button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
•
If you do not wish to spin the clothes, turn
the programme selector knob to the “Drain”
programme and press the
“Start/Pause”
button.
“Spin” button
•
Every programme has a predefined spin speed.
•
Press the button to set another spin speed.
•
If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.
START DELAY
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
•
Do not use liquid detergent when activating this
function.
•
Select programme, spin speed and options.
•
Press the “Start delay” button several times to select
a delay time by 1 to 23 hours.
•
Start the programme (see “Programme Start”). The
indication next to the “Start delay” button lights up
and goes off when the programme starts.
•
Once having pressed the
“Start/Pause”
button,
the countdown of the time delay begins. When the
programme starts, the start delay indicator light
goes off and is replaced by the programme sequence
indication.
•
After the
“Start/Pause”
button has been pressed,
the number of hours preselected can be changed by
pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
•
Turn the programme selector to another position or
press the
“Reset”
button.
..after having pressed the “Start/Pause” button:
•
Press the
“Reset”
button for at least 3 second. The
start delay indicator light goes off.
PROGRAMME START
Open the tap and press the
“Start/Pause”
button.
The blinking light next to the
“Start/Pause”
button
becomes constant. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain. When
the programme phrase is finised, the corresponding
indication goes out.
1.
PREPARATION OF WASH CYCLE
Load the laundry, close the door and add detergents
as indicated on the front page and as described
in the chapter “Detergent and Additives” in your
Instructions for Use.
2. Turn the
programme selector
to the desired
programme and temperature.
3. The display shows the programme duration and the
predefined spin speed. The indication lamp next to
the “
Start/Pause
” button blinks.
4. If you do not start the programme soon after having
made your choice, the washing machine will switch
off automatically after about a quarter of an hour.
To switch the washing machine on again, turn the
programme selector to “O” and afterwards to the
desired programme again.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Prewash” button
•
Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 15 min.
•
Do not use liquid detergent for the main wash when
activating the Prewash option.
“LID OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel a running programme before the end”.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”
No or not sufficient inlet water.
“Service”
Failure or malfunction of an electrical component.
“Clean pump”
Waste water is not pumped out.
Spin speed on display blinks:
unbalance during
spinning
•
PROGRAMME END
The “Lid open” indication lights up and the display
shows “End”. After about a quarter of an hour, the
washing machine will switch off completely to save
energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the interior
of the machine to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the
“Start/Pause”
button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE THE
END
The
“Reset”
button cancels a programme before the
end.
•
Press the
“Reset”
button for at least 3 seconds. The
water is drained out; it may last a while until you can
open the lid.
Programme
Tempe-
rature
(°C)
Load
(kg)
Water
(l)
Energy
without “Time”
(kWh)
Approx. Programme Duration (hrs : min)
%
without “Time”
with “Time”
Cotton
95
6.0
53*
1.91
2:05
1:55
64
Cotton
60
6.0
48
1.14
2:30
1:45
Cotton
40
6.0
48
0.75
2:15
1:30
Baby
40
4.0
41
0.58
1:44
-
Synthetic
60
3.0
50*
0.90
2:05
1:14
47
Synthetic
40
3.0
40
0.50
1:50
0:59
Sport
30
3.0
50
0.45
2:05
1:14
Sensitive
40
1.5
50
0.55
0:45
-
Sensitive
30
1.5
50
0.50
0:41
-
Mix
40
3.0
40
0.45
1:00
-
68
Quick wash 15’
30
3.0
30
0.15
0:15
-
Wool
40
1.0
40
0.55
0:35
-
Hand wash
20
1.0
40
0.40
0:30
-
Eco Cotton
60°
**
60
6.0
48
1.02
4:00
-
62
Eco Cotton
60°
**
60
3.0
35
0.76
2:10
-
Eco Cotton
40°
**
40
3.0
35
0.57
2:00
-
CONSUMPTION DATA
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer to the
default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximete remaining moisture content (%). After programme end and spinning with maximum selectable spin speed, in default programme setting.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Reference Programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
