![background image](/i/loewe/156614/loewe-blutech-vision-3d/h/loewe-blutech-vision-3d-004.png)
BluTechVision 3D
- 4 -
Instructions for Use
Deutsch
English
Français
Italiano
Español
Nederlands
Português
Magyar
Polski
Č
eština
For your safety, and to avoid unnecessary damage to your unit,
please read and follow the safety advice below:
Intended Use and ambient conditions
This Set is intended exclusively for rendering video and audio signals
and is designed for use in residential apartments or office premises.
It must not be used in rooms with a high level of
humidity
(e.g. bath-
room, sauna) or a high
dust concentration
(e.g. workshops). The
manufacturer‘s warranty is only valid for use in the specified permis-
sible environment.
If the unit is used outdoors, make sure that it is protected from
moisture
(rain, dripping water and splashing water or dew). High humidity and
dust concentrations lead to leakage currents in the device. This can
result in a shock hazard by touching it or even fire.
If you have moved the unit out of the
cold
into a warm environment,
leave it switched off for about an hour because of a possible formation
of
condensation
.
Do not place
objects
containing
liquids
on top of the unit. Protect the
device against dripping and splash-
ing water.
Candles
or
naked flames
must be
kept away from the unit at all times
to prevent it from catching fire.
Never place the Set in a location
where it is exposed to
vibrations
.
This can lead to material overload.
Power supply:
Incorrect voltages
can damage the unit. This device may only be con-
nected to a power supply with the voltage and frequency indicated on the
type plate using the supplied mains cable. The
mains plug
of the unit
must be easily accessible so that the device can be disconnected from
the mains at any time. When unplugging the unit from the mains, pull at
the connector body and not at the
cable
. The cables in the mains plug
could otherwise be damaged and could cause a
short-circuit
when
plugged in again.
Lay the
mains cable
so that it cannot be damaged. The power cable
may not be kinked or laid over sharp edges, stood on or exposed to
chemicals
; the latter also applies to the unit as a whole. A power
cable with damaged insulation can cause
electric shocks
and poses
a
fire risk
.
Air circulation and high temperatures
Ensure that there is at least 3 cm free space on the sides and above
the set for air circulation, if the set is placed in a
cabinet
or on a
shelf
or is hung up.
Like any electronic device, your unit requires
air for cooling
. Obstruc-
tion of the air circulation can cause fires.
Prevent
metal items
, needles, paper clips, liquids, wax, or similar
items, from getting into the interior of the device through the
vent
slots
in the rear panel. Such objects can cause
short circuits
in the
unit, which could possibly cause a fire.
If something should get into the
interior of the set
then immediate-
ly unplug the mains plug of the device and contact the
field service
for more information.
Set-up
Place the unit on an
even, firm, horizontal surface
. Particularly
ensure that the set does not protrude to the front when placed in or
on pieces of furniture.
Set up the device where it is not exposed to direct
sunlight
and where
it is not exposed to additional heating by
radiators
.
The picture and sound of a TV set, a player or a radio in the vicinity
can be distorted. If this is the case, do not place the unit in the direct
vicinity of these devices.
Set up the device so that the infrared signal of the remote control can
reach the display of the player without hindrance (or if this is not
possible, see "Digital Link HD (HDMI CEC)" page 10).
Do not place any strong artificial light source in front of the unit. This
could have a detrimental effect on the infrared reception.
n
For your safety