Инструкция для President GEORGE ASC

(скачивание инструкции бесплатно)
Формат файла: PDF
Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.
Дополнительно: Чтение инструкции онлайн
background image

8

* Using an external SWR meter (e.g. SWR 1 or SWR 2 PRESIDENT):

a)

To connect the SWR meter:

- Connect the SWR meter between the CB radio and the antenna as close as

possible to the CB (use a maximum of 40 cm cable, type CA 2C PRESIDENT).

b)

To adjust the SWR meter:

- Set the CB to channel 20.
- Put the switch on the SWR meter to position «CAL» (= calibrate).
- Press the «push-to-talk» switch on the microphone.
- Bring the index needle to 

 by using the calibration key.

- Change the switch to position SWR (reading of the SWR level). The reading on

the V.U. meter should be as near as possible to 1. If this is not the case, re-adjust
your antenna to obtain a reading as close as possible to 1. (An SWR reading
between 1 and 1.8 is acceptable).

- It will be necessary to re-calibrate after each adjustment of the an-tenna.

Your CB is now ready for use.

B) HOW TO USE YOUR  CB:

1) POWER:

a)

One quick press on this key turns your CB on and off.

b)

A longer depression (about three seconds) activates the protection by code
procedure. The code must be re-entered to put the set on.

NOTE

 :

 As soon as your set goes off, the last configuration is memorised ready

for the next time.

2) DIMMER:

a)

Set turned off (but with power supply connected):  by pressing the DIMMER key

the message 

 flashes indicating clearly and permanently the code

protection in your absence. You should not leave this function on for more
than three days without starting your vehicle's engine (risk of flat battery).

b)

With the set turned on: This key allows you to adjust the luminosity of the display.

3) DC (Double Colour):

With this key you can change the colour of the digital display to either amber
or green, so that your set is in harmony with the interior of your vehicle.

4) VOLUME:

To increase the volume, turn this knob clockwise.

5) SQUELCH:

Suppresses undesirable back-ground noise when there are no
communications. Turn the squelch knob clockwise to the exact point where
all background noise disappears. This adjustment should be done with precision
as, if set to maximum, only the strongest of signals can be received. Squelch
does not effect either sound or transmission power, but allows for considerable
improvement in listening comfort.

6) CHANNEL SELECTOR KEYS «CH 

», «CH 

» AND/OR

ROTARY KNOB:

The two keys, «CH 

» and «CH 

» on the microphone and on the front panel,

allow you to go up and down the channels. This can also be done with the
channel rotary knob.

«CH 

» key : one quick press allows you to go down by 

one

 channel,

continued pression allows you to descend five channels per second.

«CH 

» key : one quick press allows you to go up by one channel, continued

pression allows you to ascend five channels per second.

7) MODE:

Use this key to select AM, FM, LSB or  USB.
The mode must correspond with that of the person with whom you
communicate.
Amplitude Modulation (AM) is for communications in areas where there are
obstacles and over medium distances.
Frequency Modulation (FM) is for nearby communications in flat, open areas.
It gives better quality of communication (squelch adjustment needs more
finesse).
Lower and Upper Side Band is used for prompt communications over long
distances (depends very much on atmospheric conditions).
A long press on the «MODE» key allows you to change from AM/FM/ to LSB/USB
and vice versa. A short press on the same key allows you to change from AM
to FM or from LSB to USB and vice versa

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Оглавление инструкции
  • Страница 1 из 21
    GEORGE Owner's manual
  • Страница 2 из 21
    Your PRESIDENT GEORGE at a glance 2
  • Страница 3 из 21
    SUMMARY INSTALLATION HOW TO USE YOUR CB 5 8 PROTECTION BY SECURITY CODE SYSTEM 14 TECHNICAL CHARACTERISTICS 16 TROUBLE SHOOTING 16 HOW TO TRANSMIT OR RECEIVE A MESSAGE 16 GLOSSARY 17 FREQUENCY TABLES 21 3
  • Страница 4 из 21
    WARNING ! Before using, be careful never to transmit without first having connected the antenna (connection B situated on the back panel of the equipment) or without having set the SWR (Standing Wave Ratio) ! Failure to do so may result in destruction of the power amplifier, which is not covered by
  • Страница 5 из 21
    Welcome to the world of the 3rd generation of CB radios. The new PRESIDENT INTERACTIVE range gives you access to top performance CB equipment. With the use of upto-date technology, which guarantees unprecedented quality, your PRESIDENT GEORGE is a new step in personal communications and is the
  • Страница 6 из 21
    2) ANTENNA INSTALLATION: 3) POWER CONNECTION: a) Choosing your antenna: - For CB radios, the longer the antenna, the better its results. Your dealer will be able to help you with your choice of antenna. Your PRESIDENT GEORGE is protected against an inversion of polarities. However, before switching
  • Страница 7 из 21
    e) Press the «METER» key, with the «push-to-talk» switch pressed down, so that the equipment is in S/RF mode. 4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING YOUR SET FOR THE FIRST TIME (without trans-mitting and without using the «push-to-talk» switch on the microphone): DISPLAY a) Connect the
  • Страница 8 из 21
    * Using an external SWR meter (e.g. SWR 1 or SWR 2 PRESIDENT): 4) VOLUME: a) To connect the SWR meter: - Connect the SWR meter between the CB radio and the antenna as close as possible to the CB (use a maximum of 40 cm cable, type CA 2C PRESIDENT). b) To adjust the SWR meter: - Set the CB to
  • Страница 9 из 21
    Example: 8) RF POWER: When you turn this knob fully clockwise the RF power (norm peak 4 watts) is at maximum. You should reduce transmission power when the communication is close to someone who does not have RF GAIN. Configuration You are in Channel 22, FM. The normal setting of this knob is on
  • Страница 10 из 21
    else disappears. Hold the microphone far enough away from this loud speaker so as to avoid the Larsen effect. 14)NB/ANL: Noise Blanker/ Automatic Noise Limiter. These filters allow the reduction of back ground noise, and some reception interference. The PA volume is regulated by the MIC GAIN knob.
  • Страница 11 из 21
    - Press «CH ▲» (+ 10 channels): Set goes to the channel 32 FM. 20)CH 19 (Channel 19 AM): Channel 19 AM is automatically selected when you depress this key. Configuration You are in Channel 22 FM. - Press «CH ▲» (+ 10 channels): Set goes to the channel 2 FM. - Press «CH19»: Frequency disappears to
  • Страница 12 из 21
    - - If a signal is detected on Channel 22 your CB listens to the channel and stays there until the end of the signal. Press «CH19» Set goes directly to Channel «CH19». - End of signal on Channel 22 FM. 21)DW (Dual Watch): This function lets you watch over Channel 19 AM and the channel you are
  • Страница 13 из 21
    By immediately pressing one of the memory keys (M1 - M4) the channel and the modulation mode currently in use will be stored in the memory. The operation is validated with a long beep. (See example after paragraph 23) - Depression of «M1»: stops flashing, appears, long beep sounds to indicate that
  • Страница 14 из 21
    b) Direct access to one of the memories, Initial configuration Channel 3 LSB. 24)SCAN: This function allows you to “scan” all the memorised channels (16). Scanning stops when a signal is detected on one of the memorised channels. At the end of the signal, scanning continues. By going into
  • Страница 15 из 21
    - if the 12 volt power supply is deconnected and/or - after a long depression (more than four seconds) of the POWER key (radio on or off). In these two cases, the CB is blocked and it is necessary to enter the correct access code. The access code, established by PRESIDENT in the factory or after
  • Страница 16 из 21
    D) TECHNICAL CHARACTERISTICS: E) TROUBLE SHOOTING: 1) GENERAL: - Channels - Modulation modes - Frequency ranges - Antenna impedance - Power supply - Dimensions (en mm) - Weight - Accessories supplied : : : : : : : : 40 AM/FM/LSB/USB from 26.965 MHz à 27.405 MHz 50 ohms 13.2 V 200 (L) x 207.5 (H) x
  • Страница 17 из 21
    Press the «push-to-talk» switch and announce your message «Attention stations, transmission testing» which will allow you to check the clearness and the power of your signal. Release the switch and wait for a reply. You should receive a reply like, «Strong and clear». If you use a calling channel
  • Страница 18 из 21
    FREQUENCY TABLES CERTIFICATE OF CONFORMITY Channel Kanal Frequency Frequenzens Channel Kanal Frequency Frequenzens 1 26,965 MHz 21 27,215 MHz 2 26,975 MHz 22 27,225 MHz 3 26,985 MHz 23 27,255 MHz 4 27,005 MHz 24 27,235 MHz 5 27,015 MHz 25 27,245 MHz 6 27,025 MHz 26 27,265 MHz 7 27,035 MHz 27 27,275
  • Страница 19 из 21
    Pays dans lesquels il existe des limitations particulières (Licence1 / Registre2 / seulement du canal 4 à 123) Countries in which there are particular restrictions Países en los cuales existe algún tipo de limitación (Licencia1 / Registro2 / solo del canal 4 a 123) Länder mit besonderen
  • Страница 20 из 21
    0233/03-01 SIEGE SOCIAL/HEAD OFFICE - FRANCE Route de Sète - BP 100 - 34540 BALARUC Site Internet : http://www.president-electronics.com E-mail : groupe@president-electronics.com
  • Страница 21 из 21