19

Absaugen und
Aufrichten

Arbeitsrichtung

Einsprühen

Saugr

ohr

Dr

uc

kleitung

Lösen und Auswaschen

Suction tube

Releasing and washing out

 Spraying

Sucking up and 
straightening

Pressur

e line

Working direction

Spray extraction system

• 

Spray the cleaning agent deep into the carpet under pressure

• 

This releases the dirt and washes out deep down into the fibres

• 

Suck up the dirty water at full power and straighten up the 
carpet pile again.

This should be always carried out in a single operation.

 Press the lever on the shut-off valve (24) until the cleaning 

agent escapes. Draw the nozzle straight over the carpet and 
press it down at the same time. The spraying volume can be 
set as required by means of the setting wheel on the handle. 
Release the valve lever to stop spraying at the end of one run 
or if stopping work. If the sprayed liquid has been sucked up, 
lift the nozzle and begin a new run but overlap slightly. In this 
way you can clean the entire area section by section.

Should there still be traces of liquid remaining on the cleaned 
areas this liquid can be sucked up without spraying again.

Make sure that the mechanical suction controller (25) is 
completely closed.

In the case of very stubborn dirt you can apply the cleaning 
agent while moving the carpet spraying nozzle forwards. The 
same treatment can also be applied by just putting the pump 
into operation.

Ensure that you do not spread too much liquid over the carpeting 
since this may cause waves or bumps in the carpet. However, these 
will disappear again after being allowed to dry for a longer period 
of time.

   Empty the waste water tank after you have used up all the 

cleaning agent from the fresh water tank to prevent the 
appliance being switched off automatically.

Should you not observe the above-mentioned instructions the 
float will automatically switch off the appliance as soon as the 
waste water tank is full. (You will clearly hear the motor be 
running at a higher speed.)

Switch off appliance, disconnect the mains plug and empty the 
waste water tank.

Hard floor cleaning

Drop the hard floor adapter over 
the carpet spraying nozzle and 
lock by means of the slide. 

By using this system you can clean 
and dry your hard floor coverings 
such as tiles, stone floors and PVC 
at one and the same time.

See carpet cleaning for 
procedure.

We recommend 

THOMAS ProFloor cleaning agent

 for hard 

floor cleaning.

Only use 

THOMAS

original products and parts

 to ensure 

perfect cleaning results.
You can get 

further supplies of the cleaning agent

 from 

your specialist dealer or the THOMAS Customer Service Department.

Before cleaning carpets

• 

Make sure that everything you want to wet clean is also suitable 
for wet cleaning. Do not wet clean your sensitive, hand-woven or 
non-fast dyed carpets, for example.

  To check this put a little cleaning agent on a white cloth and rub on 

the carpet at a not too obvious spot. It can be assumed that the dye 
is colourfast should no traces of dye appear on the cloth.

  Should this not be the case do not wet clean the carpet.
  Please consult your specialist carpet dealer should you have any 

doubts.

  Should the carpet have been shampooed earlier on it may well 

be that increased foaming will occur in the waste water tank when 
using the THOMAS HYGIENE PLUS T2 for the first time. Add half 
a cup of vinegar to the waste water tank to prevent any further 
foaming.

  Immediately switch off the appliance and empty the waste water 

tank should foam escape from the air outlet.

  When using the THOMAS cleaning concentrate for thorough 

cleaning there will be no increased foaming because this cleaning 
detergent contains a special anti-foaming agent.

  You should not walk over your cleaned carpet as long as it is wet.
  The room should be well ventilated both while cleaning and after-

wards to ensure quick drying.

Carpet cleaning

Take the hygiene box out of the appliance resp. pull the 
AQUA-filter by its handle out of the waste water tank, and 
insert the anti-splash grid. Also take the HEPA filter out of the 
appliance.

Close intake opening of the hygiene box with the hinged cap.

Fit the anti-splash grid and waste water tank on the appliance. 
Make sure that both the wet filter (13a) and the motor protection 
filter (15) are fitted.

Remove the fresh water tank for filling (draw tank straight 
upwards and out of the cleaner) or fill up directly in the 
appliance. In this case you have to lift up fresh water tank cover.

When filling make sure that no impurities get 
into the fresh water tank which will prevent the 
closing valve from functioning properly. 

Fill up with cleaning agent and water through the grip lug 
(max. 2.4 litres).

   We recommend 

THOMAS ProTex original cleaning 

detergent

 for cleaning carpets.

See label on the cleaning agent bottle for application and 
dosage.

Use hand warm water (max. 30°C).

Connect up suction hose and fit telescopic suction tube.

 Fit carpet spray nozzle, spray hose to the suction tube with 
fast coupling and move upwards and place on the shut-out 
valve and lock by turning. Afterwards fasten the spray hose 
by means of the two tube clips on the suction tube.

Pull out the mains power supply plug and cable from the 
appliance and connect up.

Switch on the appliance and set for maximum suction power. Switch 
on pump. Control lamp comes on.

2.

1.