4
ENGLISH
given all the necessary instructions on safety
measures and information about danger, that
can be caused by improper usage of the unit.
•
Keep the unit out of reach of children.
•
Never allow children to use the unit as a toy.
•
The unit is intended for household usage
only.
Power connection
–
To connect the unit to the mains insert the
plug of power cord (18) into the socket. Make
sure that unit operating voltage corresponds
to voltage of your mains.
–
The unit is equipped with an integrated bat-
tery reserve supply system, that allows to
save settings of current time, timer, alarm and
recorded radio stations in case of AC supply
voltage interruption. Once the voltage gets
normal, the unit switches to supply from the
net adapter.
–
Open the battery compartment lid (19) hav-
ing preliminary unscrewed the fixing screw.
Insert a CR2032 battery (not included), fol-
lowing the polarity.
–
Close the battery compartment lid (19) and
tighten up the screw.
Attention!
Batteries leakage can cause injuries or unit dam-
age. In order to avoid unit damage, follow these
instructions:
–
insert the battery following the polarity (“plus”
upward);
–
remove the battery if you are not planning to
use the unit for a long time;
–
do not dismantle the battery, do not subject it
to high temperatures; and
–
replace the battery in time.
Date and time setting
1.
Connect the unit to the mains.
2.
Press and hold the «CLK.ADJ.» button (7).
The year digits will start flashing on the dis-
play.
3.
Use the buttons (8) and (9) to select the nec-
essary year.
4.
Press the «CLK.ADJ.» button (7)
.
The month
digits will start flashing on the display.
5.
Use the buttons (8) and (9) to select the nec-
essary month.
6.
Press the «CLK.ADJ.» button (7)
.
The day
digits will start flashing on the display.
7.
Use the buttons (8) and (9) to select the nec-
essary day.
8.
Press and hold the “CLK.ADJ.” button (7),
time format symbols will start flashing on the
display: 24 hours (24 Hr) or 12 hours (12 Hr).
9.
Use the buttons (8) and (9) to select the time
format (12 Нr or 24 Нr).
10.
Press the «CLK.ADJ.» button (7).
The hour
digits will start flashing on the display.
11.
Use the buttons (8) and (9) to select the
necessary hour.
Note: To set the afternoon time in 12 hours
format (12 Hr) consequently press the buttons
(8) and (9) until the indicator (26) «PM» appears.
12.
Press the «CLK.ADJ.» button (7). The minute
digits will start flashing on the display.
13.
Use the buttons (8) and (9) to select the nec-
essary minutes.
14.
To finish the setup procedure press the “CLK.
ADJ.” button (7).
Note
:
If buttons (8) and (9) are not pressed
within 30 seconds during setup process, the unit
will switch to the current time mode.
Current date view
1.
To view the date in the current time mode
(radio is off) press the «Y-M-D» button (8).
2.
To view the year, current date and time con-
sequently press the «Y-M-D» button (8).
Setting a clock to summer/winter time
1.
Connect the unit to the mains.
2.
Press and hold the “DST/C-F” button (9) until
the time digits change.
Alarm setup (ALARM 1 and ALARM 2)
1.
To view the settings of the first alarm in the
current time mode press the «ALARM 1»
button (4).
2.
Press again and hold the «ALARM 1» button
(4) in the mode of alarm settings. The hour
digits will start flashing on the display.
3.
Use the buttons (8) and (9) to select the
necessary hour.
4.
Press the “ALARM 1” button (4). The minute
digits will start flashing on the display.
5.
Use the buttons (8) and (9) to select the nec-
essary minutes.
6.
Press the “ALARM 1” button (4).
Symbols of
alarm signal repeating mode will appear on
the display . Use the buttons (8) and (9) to
select the necessary mode.
1-1 without repeat,
1-5 alarm signal repeating from Monday to
Friday,
1-7 alarm signal repeating seven days a week,
6-7 alarm signal repeating on Saturday and
Sunday.
VT-3516 IM.indd 4
26.01.2012 12:48:27
